Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Instructions
You will need a craft knife or other sharp knife, a pair of scissors, some glue and a glue spreader. The best type of glue to use is white school glue (PVA.) Print out the parts sheets onto thin cardboard. Photocopier card is ideal. Notice that the parts pages are marked front and back. Print out a front page, flip it over, then print the back onto the same sheet. Allow the ink to dry completely before continuing. Before cutting anything out, score along all the dotted lines and cut out any holes with a craft knife. Both these jobs are easier to do on full sheets of card. Dashed lines are hill folds, dotted lines are valley folds. Cut along the solid lines. Grey areas show where to glue Youll need four coins about this size Dashed lines are hill folds Dotted lines are valley folds
Cut out
1
Glue the flaps 1&2 down.
2
Fold round and glue the four coin holders to make little packets. These provide weight to help the goat move more positively. Glue Glue together the two push buttons (14-25) as shown. Glue a coin holder into each push button.
Fold over the two flaps (1&2) so that they are at ninety degrees as shown above and glue them into place. Glue the box together as shown in the picture. Assemble and glue on the box stiffener. (3-13)
Assemble the lower push rods and glue them into place on the push buttons. (26-29) Be careful with the next bit!
and-goat Instructions 1
an
d-
go
at
an
d-g
t oa
Before you glue the push buttons into place make sure that you thread the two push rods up through the hole in the top of the box. Now glue the push buttons into place (30-31). Make sure that they move freely.
5
lift link
6
Glue together the neck (38)
hinge
Glue the hinge to the neck (39) Glue the two remaining coins onto the lift links so that the coin lines up with the circle sector. coin
pivot
Assemble the push rods (41) and glue them into place (42-43) pivot lift link
Glue together the pivot and the two lift links (32-34) Glue the hinge into place on the pivot (35) Glue the two lift links onto the other side of the pivot. (36-37) neck
hinge
push rod
Make sure that the alignment piece is glued into place inside the body lining it up with the two creases. (40) Make the two body inners by folding them round and gluing them. (44 - 45)
Glue the two sides into the body carefully lining up the curved edges. (46 - 47) Assemble the four legs. (48) Glue the four legs to the body making sure you match the orange and green circles (49)
and-goat Instructions 2
8
Assemble the head and horns. (50-53) Glue the pivot into place on the inside of the body. (54) Glue the head to the neck (55-56) Glue on top flap of the back piece. (57) Glue the left side feet to the box (58) Tricky, fiddly job next. Join the two halves of the two pushrods. (59) Assemble and glue on the tail. Glue down the last two flaps of the back piece. (60) Glue the right side feet to the box. (60) Finally, glue the ears and the eyes into place. Your and-goat is now compete!
and-goat
0 0
1 0
and-goat Instructions 3
Coin Holder
Box 3
9 58 61 Cut out 61 58
and-goat
61
13
8 5 Cut out 6
58
Coin Holder
and-goat
12
and-goat
61
13
58
11 6 5
9 2 8 31 11 30
10 4 12 1
49
49
45
44
49
Body Inner
Back
21
Coin Holder
Push Button
31
18
16
28
46 49 24 15
17
47
30
29
44
45
25
21
coin
14
16
19
20
22
23 coin 20
15
25 24 14
17 19 18
Eyes
34
Horn
Horn
Head
Coin 43
52
52
53
53
Ears
50
Lift Link 37
51
Pivot
37
54 36
32
51
35
50
55 34
53
53
56 52
50
33
50
27 39 35
26
28
59
29
52
59 42 32
51
51
38 41 43 41
56
49
49
Body
Legs
Legs
48 49 48
48 49 48
Tail
60
54 Alignment Piece
60
48
48
48
48
47 58 58 58 58
40
40
46
60
61 Front 57
61
61
61
60