Sei sulla pagina 1di 1

+650/+655V R7 121k/1W R6 100k/1W 218V RCA XLR G 1 3 + 2 R1 100k R2 511R VT1a 6SL7 R3 2k R4 127k/1W R24 127k/1W NE-2H R21

100k SW3 R22 511R R23 2k R5 127k/1W R8 1k -255/-260V R11 33.2k/2W R31 33.2k/2W R10 38.3k/2W R9 2k VT2a 6SN7 VT3a 6SN7 C1 0.22u 650V C7 20u/1200V

+545/+550V C9 20u/630V * Kiwame 2W / 1000V

445V R12 1k

VT4 KT88 R36 1k R37 100k/1W

R40 330R*

R41 1k

R45 330R* VT5 KT88

Bartolluci Model 555 Primary; 300H, 3800ohm P-P

+212V

R38 30.9R

R39 10k

R44 10k

R43 30.9R

BIAS TEST POINTS (2.01V = 65mA) R48 30.9R R46 1k VT6 KT88 R47 100k/1W R56 32.4k VR1 25k R58 100k C3 0.22u 200V VR2 25k R59 100k C4 0.22u 200V -102V Rev. C 6/7/2001 330R* R50 R51 1k R53 30.9R VT7 KT88 330R* R55

R25 127k/1W C5

R30 38.3k/2W R29 2k VT2b 6SN7 C2 0.22u 650V

R49 10k

R54 10k

OUT (8ohm SHOWN)

VT1b 6SL7

20u/630V R28 1k

For unbalanced input (RCA) close SW3. R26 100k/1W R27 121k/1W

R32 1k

VT3b 6SN7 SET-UP: 1/ Each bias potentiometer should be set initially at the most negative end of the range. After 5 minutes warm-up adjust each bias setting to 1.62V+/-0.01V (50mA). 2/ After 20 minutes warm-up with the amplifier 'right side up' supply voltages should be adjusted to within the values shown Re-adjust after a further hour. 3/ Now adjust each bias setting to 2.01V +/-0.01V for 65mA (or to a value corresponding with the intended bias current.) Note: With new tubes, the bias current can be expected to drift significantly for the first 24-48 hours. 4/ Node voltages are given for diagnostic purposes only and will vary with the individual tubes used. +650/+655V

RECOMMENDED COMPONENTS: Resistors, Holco metal film; H4 (1/2W, 1%) and H2 (1W, 1%) Roerderstein Metal Film MK8 (2W, 2%) unless stated otherwise. Large capacitors, Solen or AEON film. Small capacitors, Multicap PPFX. Coupling capacitors, VTV "Ultra-Tone". This document & the information herein is the sole property of Richard F. Sears and shall not be used for commercial purposes without the express written permission of Richard F. Sears. (richard@triodeguy.com)

R57 17.8k C11 5u 200V

KT88 (TRIODE) - 60W


PARALLEL PUSH-PULL AMPLIFIER DRIVE & OUTPUT STAGE (Pg 1 of 3) PROGRAM FILES\DATA\KT88_AUD RICHARD F. SEARS 12/3/2000

Potrebbero piacerti anche