Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Jenkins Valves
254 Henry Street
Brantford, Ontario N3T 5T7
Tel: 519-759-3911
Tel: 800-563-6302
Fax: 519-759-7970
www.cranevalve.com
SINCE 1864
JENKINS
®
General Index
Jenkins Valve also manufactures bronze ball valves, iron wafer and lug butterfly valves, bronze and
iron gate globe and check valves, and alloy valves. Brochures and catalogs are available on request.
-1-
SINCE 1864
JENKINS
®
Jenkins valves are universally accepted by industry for virtually every application ranging from vacuum pres-
sures and cryogenic temperatures to elevated pressures and temperatures.
Since Jenkins valves are used in a variety of applications, the following descriptions may provide a basic guide-
line in the selection of steel valves.
Gate Valves
Gate valves serve as efficient stop valves with flow in either direction. They are commonly used where a mini-
mum pressure drop is important. Throttling is not recommended because partially open gate valves exhibit flow
characteristics not conducive to accurate and consistent flow control. Also, the valves may be damaged by the
high velocity across the seats. They function best fully open or fully closed.
Globe Valves
Globe valves are ideal for throttling service. Their flow characteristics permit accurate and repeatable flow
control. However, caution must be exercised to avoid extremely close throttling when pressure drop exceeds
20%. This creates excessive noise, vibration and possible damage to valves and piping. When these conditions
are anticipated, consult Jenkins for recommendations.
CAUTION: When servicing, disassembling or disposing of valves containing asbestos gaskets or packing, avoid breathing dust or fibers from these parts.
Disposal of asbestos and asbestos related products should comply with local, state and federal laws and regulations.
-2-
SINCE 1864
Marking and identification of Jenkins steel valves conforms to the Manufacturer's Standardization Society (MSS) Standard Marking System
for Valves, Fittings, Flanges and Unions (MSS SP-25) as well as the appropriate BS valve standard.
It is important to properly identify valves in service to allow for the ordering of replacement parts or address questions or concerns relating
to our products. Body markings and information shown on the identification plate helps to properly identify valves, allowing timely and accurate
responses to such inquiries.
Integrally cast body marking data includes the following information and helps to provide traceability:
• Jenkins logo
• Pressure class
• Valve size
• “Steel” symbol for the grade of material (i.e. WCB for carbon steel)
• Heat number – on body and bonnet (cast or stamped)
The body markings are supplemented by an identification plate which, depending on valve type and size, is mounted in the most practicable
position. Tag location for gate and globe valves is typically on the valve yoke. Check valve tags are typically mounted on the rim cap.
When purchasing valves, reference should also be made to MSS 6683 “Guide to the Installation and Use of Valves” as well as to MSS SP-
92 “Valve User Guide.” Inquires relating specifically to Jenkins products may be referred to our factory or customer service department.
JENKINS
STEEL
PSI/ °F MAX STEM
(MATERIAL) XXXXXX
(CLASS)
XXXXX (ID) YY
Cast or Stamped
on raised pad
Product Marking
-3-
SINCE 1864
JENKINS
®
Cast Steel Gate Valves
General Information • Class 150, 300 and 600 Valves
Features
Flexible Wedge
• Compensates for deformation of body due to pipe stresses
• Will not stick when valve is closed hot and allowed to cool
Standards
These valves comply with the applicable requirements of the following standards:
• API 600
• API 598
• ANSI B16.34
• ANSI B16.10
• ANSIB16.5
Notes
• Standard material is ASTM A216 Grade WCB.
• Standard trim is XU (13% Cr to hardface) which is suitable for a wide range of applications.
• See Engineering Data section for end flange dimensions and drilling templates.
-4-
SINCE 1864
Jenkins gate valves offer the ultimate in dependable service for steam, air, gas, oil, oil vapor, and high pressure installations. All have
straight-through ports to assure minimum turbulence, erosion, and resistance to flow. They are available in a wide variety of trims.
-5-
SINCE 1864
JENKINS
®
Cast Steel Gate Valves Figure J1009B8F
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
C Flange Dimensions ANSI B16.5
Basic Design API 600
Testing API 598
-6-
SINCE 1864
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
Flange Dimensions ANSI B16.5
Basic Design API 600 C
Testing API 598
-7-
SINCE 1864
JENKINS
®
Cast Steel Gate Valves Figure J1012B8F
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
C Flange Dimensions ANSI B16.5
Basic Design API 600
Testing API 598
-8-
SINCE 1864
Features
Disc Type
• Plug type disc is standard for Class 150 valves, sizes 2"-10"; Class 300 valves, sizes 2"-8";
and Class 600 valves, sizes 2"-4"
• Equilibrated type disc is standard for Class 150 valves, sizes 12" and larger; Class 300 valves, sizes 10"
and larger; and Class 600 valves, sizes 6" and larger
Standards
These valves comply with the applicable requirements of the following standards:
• API 598
• ANSI B16.34
• ANSI B16.10
• ANSIB16.5
Notes
• Standard material is ASTM A216 Grade WCB.
• Standard trim is XU (13% Cr to hardface) which is suitable for a wide range of applications.
• See Engineering Data section for end flange dimensions and drilling templates.
-9-
SINCE 1864
JENKINS
®
Cast Steel Globe Valves
Typical Globe Valve Features
Jenkins globe valves are highly efficient for services requiring frequent operation and throttling when pressure drop across the valve is about
20% of inlet pressure. Closer throttling, creating higher pressure drops may cause cavitation or excessive velocities which could cause high
noise levels, vibration and possible damage to the valve or adjacent piping. Globe valves can be equipped with optional operators and are
available with a variety of trims to match service requirements.
-10-
SINCE 1864
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10 C
Flange Dimensions ANSI B16.5
Testing API 598
-11-
SINCE 1864
JENKINS
®
Cast Steel Globe Valves Figure J1042B2
Industry Standards
Steel Valves ANSI B16.34
C Face-to-Face/End-to-End ANSI B16.10
Flange Dimensions ANSI B16.5
Testing API 598
-12-
SINCE 1864
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
Flange Dimensions ANSI B16.5 C
Testing API 598
-13-
SINCE 1864
JENKINS
®
Cast Steel Check Valves
General Information • Class 150, 300 and 600 Valves
Features
Disc Type
• Class 150 valves-2"-12" and Class 300 valves-sizes 2"-8" feature an internally mounted hinge pin
which eliminates a leak path
• For class 600 valves, a ring joint bonnet gasket assures positive seal against leakage and accurate
alignment of moving parts
Standards
These valves comply with the applicable requirements of the following standards:
• API 598
• ANSI B16.34
• ANSI B16.10
• ANSIB16.5
Notes
• Standard material is ASTM A216 Grade WCB.
• Standard trim is XU (13% Cr to hardface) which is suitable for a wide range of applications.
• See Engineering Data section for end flange dimensions and drilling templates.
-14-
SINCE 1864
The value for v is equal to flow in feet per second and v is the specific volume of fluid in cubic feet per pound. Sizing swing check valves
on this basis may often result in the use of valves that are smaller than the pipe in which they are used, necessitating the use of reducers
for installation. The pressure drop will be no greater than that of the larger valve that is only partially open, and valve life will be greatly
extended. The added bonus, of course, is the lower cost of the smaller valve.
There is no tendency for the seating surfaces of swing check valves to gall or score, because the disc meets the flat seat squarely
without rubbing contact upon closing. The regularly furnished “X” or “XU” trim is therefore suitable for all services that require U trim at
temperatures to 1100° F. “A” and “L” or “AU” and “LU” trims are also available when specified.
Jenkins cast steel swing check valves can be furnished with outside lever and adjustable weight when so ordered. With the lever and
weight mounted so that the weight assists the disc in closing, the valve closes more rapidly when flow stops, thus minimizing reversal of
flow and resultant surge and shock. With the lever and weight mounted to balance the weight of the disc, the valve becomes more
sensitive to low inlet velocities.
Swing check valves are used to prevent reversal of flow in horizontal or vertical pipe lines. In vertical lines, or for any angle from horizon-
tal to vertical, they can be used for upward flow only.
-15-
SINCE 1864
Figure
JENKINS
®
Cast Steel Swing Check Valve J1025B2
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
Flange Dimensions ANSI B16.5
Testing API 598
-16-
SINCE 1864
Figure
J1026B2 Cast Steel Swing Check Valve JENKINS
®
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
Flange Dimensions ANSI B16.5
Testing API 598
-17-
SINCE 1864
Industry Standards
Steel Valves ANSI B16.34
Face-to-Face/End-to-End ANSI B16.10
Flange Dimensions ANSI B16.5
Testing API 598
B
Dimensions and Weights
Valve Weight Dimensions (inches)
Size (pounds) A B
2 62 11.50 6.88
21/2 84 13.00 7.88
3 115 14.00 9.12
4 192 17.00 11.62
6 495 22.00 14.25
8 780 26.00 15.75
A 10 1400 31.00 18.12
12 1750 33.00 20.50
-18-
SINCE 1864
Pressure-Temperature Ratings
Pressure-Temperature Ratings
(comply with ANSI B16.34-1981 – Standard Class)
500 170 170 170 170 170 170 500 1200 1330 1285 1280 1165 1330
600 140 140 140 140 140 140 600 1095 1210 1210 1210 1065 1210
650 125 125 125 125 125 125 650 1075 1210 1210 1210 1065 1210
700 110 110 110 110 – – 700 1065 1135 1135 1135 – –
Class Class
150 600
800 80 80 80 80 – – 800 825 995 1015 1015 – –
850 651 65 65 65 – – 850 5351 880 975 975 – –
900 501 50 50 50 – – 900 3451 705 900 900 – –
950 351 35 35 35 – – 950 2051 520 755 755 – –
1000 201 20 20 20 – – 1000 1051 365 445 535 – –
1050 – 202 20 20 – – 1050 _ 280 275 400 _ _
1100 _ 202 _ _ _ _ 1150 _ 205 190 225 _ _
1150 _ 202 _ _ _ _ 1150 _ 140 _ _ _ _
1200 _ 202 _ _ _ _ 1200 _ 90 _ _ _ _
-20 to 100° 740 750 750 750 695 750 -20 to 100° 2220 2250 2250 2250 2085 2250
200 675 750 710 715 655 750 200 2025 2250 2135 2150 1970 2250
300 655 730 675 675 640 730 300 1970 2185 2020 2030 1915 2185
400 635 705 660 650 620 705 400 1900 2115 1975 1945 1850 2115
500 600 665 640 640 585 665 500 1795 1995 1925 1920 1745 1995
600 550 605 605 605 535 605 600 1640 1815 1815 1815 1600 1815
650 535 590 590 590 525 590 650 1610 1765 1765 1765 1570 1765
700 535 570 570 570 _ _ 700 1600 1705 1705 1705 _ _
750 505 530 530 530 _ _ 750 1510 1595 1595 1595 _ _
Class Class
300 900
800 410 500 510 510 _ _ 800 1235 1490 1525 1525 _ _
850 2701 440 485 485 _ _ 850 8051 1315 1460 1460 _ _
900 1701 355 450 450 _ _ 900 5151 1060 1350 1350 _ _
950 1051 260 380 380 _ _ 950 3101 780 1130 1130 _ _
1000 501 190 225 270 _ _ 1000 1551 575 670 805 _ _
1050 _ 140 140 200 _ _ 1050 _ 420 410 595 _ _
1100 _ 105 95 115 _ _ 1100 _ 310 290 340 _ _
1150 _ 70 _ _ _ _ 1150 _ 205 _ _ _ _
1200 _ 45 _ _ _ _ 1200 _ 135 _ _ _ _
-20 to 100° 990 1000 1000 1000 925 1000 -20 to 100° 3705 3750 3750 3750 3470 3750
200 900 1000 950 955 875 1000 200 3375 3750 3560 3580 3280 3750
300 875 970 895 905 850 970 300 3280 3640 3365 3385 3190 3640
400 845 940 880 865 825 940 400 3170 3530 3290 3240 3085 3530
500 800 885 855 855 775 885 500 2995 3325 3210 3200 2910 3325
600 730 805 805 805 710 805 600 2735 3025 3025 3025 2665 3025
650 715 785 785 785 695 785 650 2685 2940 2940 2940 2615 2940
700 710 755 755 755 _ _ 700 2665 2840 2840 2840 _ _
750 670 710 710 710 _ _ 750 2520 2660 2660 2660 _ _
Class Class
400 1500
800 550 665 675 675 _ _ 800 2060 2485 2540 2540 _ _
850 3551 585 650 650 _ _ 850 13401 2195 2435 2435 _ _
900 2301 470 600 600 _ _ 900 8601 1765 2245 2245 _ _
950 1401 350 505 505 _ _ 950 5151 1305 1885 1885 _ _
1000 701 255 300 355 _ _ 1000 2601 960 1115 1340 _ _
1050 _ 190 185 265 _ _ 1050 _ 705 685 995 _ _
1100 _ 140 130 150 _ _ 1100 _ 515 480 565 _ _
1150 _ 90 _ _ _ _ 1150 _ 345 _ _ _ _
1200 _ 60 _ _ _ _ 1200 _ 225 _ _ _ _
-19-