Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SERVICE MANUAL
S61U6LC-20B2U
MODEL LC-20B2U
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
CONTENTS
Page Page
» IMPORTANT SERVICE SAFETY Ë INVERTER-A and INVERTER-B UNIT ...... 41
PRECAUTION.................................................... 2 » PRINTED WIRING BOARD ASSEMBLIES ..... 42
» SPECIFICATIONS ............................................. 4 » PARTS LIST
» OPERATION MANUAL ...................................... 5 Ë ELECTRICAL PARTS ................................ 47
» DIMENSIONS .................................................... 9 Ë INVERTER-A UNIT .................................... 47
» REMOVING OF MAJOR PARTS ..................... 10 Ë INVERTER-B UNIT .................................... 47
» ADJUSTING PROCEDURE OF Ë MAIN UNIT ................................................ 48
EACH SECTION .............................................. 13 Ë TERMINAL UNIT ....................................... 51
» TROUBLE SHOOTING TABLE ........................ 16 Ë OPERATION UNIT ..................................... 54
» CHASSIS LAYOUT .......................................... 20 Ë JACK UNIT ................................................ 54
» BLOCK DIAGRAM ........................................... 22 Ë R/C RECEIVER UNIT ................................ 55
» DESCRIPTION OF SCHEMATIC DIAGRAM .. 24 Ë CABINET PARTS LOCATION .............. 55, 58
» SCHEMATIC DIAGRAM Ë CABINET AND MECHANICAL PARTS ..... 56
Ë OPERATION and R/C RECEIVER UNIT ... 25 Ë ACCESSORIES PARTS ............................ 58
Ë MAIN UNIT ................................................ 26 Ë PACKING PARTS ....................................... 58
Ë TERMINAL UNIT ....................................... 36 » PACKING OF THE SET ................................... 59
Ë JACK UNIT ................................................ 40
SAFETY NOTICE
Many electrical and mechanical parts in LCD television and shaded areas in the Replacement Parts Lists and
have special safety-related characteristics. Schematic Diagrams.
These characteristics are often not evident from visual For continued protection, replacement parts must be
inspection, nor can protection afforded by them be identical to those used in the original circuit.
necessarily increased by using replacement components The use of a substitute replacement parts which do not
rated for higher voltage, wattage and etc. have the same safety characteristics as the factory
Replacement parts which have these special safety recommended replacement parts shown in this service
characteristics are identified in this manual; electrical manual, may create shock, fire or other hazards.
components having such features are identified by “ å”
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
2
LC-20B2U
3
LC-20B2U
Specifications
Items Model LC-20B2U
LCD panel 19.7” TFT LCD
Number of dots 921,600 dots VGA
Video color systems N358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60
Destination USA/Latin A/Twn
TV Standard (CCIR) NTSC/PAL-M/PAL-N
TV function TV Tuning System PLL 181 ch.
STEREO MTS+SAP
CATV 125 ch.
3 Dimensional Y/C separation circuit Yes (N358 only)
Digital comb filter Yes
Brightness 430 cd/m2
Lamp life 60,000 hours
Viewing angles H: 160° V: 160°
Audio amplifier 2.5 W × 2
Speakers ø 2 in. (5 cm), 2 pcs.
AV1 AV-IN1, S-VIDEO-IN
AV2 AV-IN2/AV-OUT
Terminals COMPONENT COMPONENT-IN, AUDIO-IN
Antenna F-Type
Headphone Mini-jack for stereo (3.5 ø)
OSD language English/French/Spanish
Power supply DC 13 V, AC 110–240 V, 50/60 Hz
Weight 18.1 lbs (8.2 kg), w/o accessories
Accessories Remote control, Batteries, Antenna cable, AC adapter,
AC cord, Cable clamps
■ Design and specifications are subject to change without notice.
4
FRONT AND REAR CONTROL OPTIONS
Main unit (front view) Main unit (rear view)
VOL (–)/(+)
CH ( )/( )
MENU UT VIDEO
AV-IN2/O
VIDEO
TV/VIDEO AUDIO (L) AV-IN2/OUT
L
MAIN POWER AUDIO AUDIO (R)
R
Operation Manual
ONENT Y
COMP
VOL CH MENU TV/VIDEO MAIN POWER Y
PB
PB
PR COMPONENT
PR
AUDIO (L)
L
5
degrees backward. The
TV set can also be
rotated 90 degrees
horizontally. Please adjust
the angle so that the TV
set can be watched most
comfortably.
SLEEP indicator AV
The SLEEP indicator lights up red when -I N
VI 1
DE
the SLEEP TIMER is set to on. O
VIDEO
AU L
POWER indicator DI
O AUDIO (L)
Remote sensor window A green indicator lights when the power is R AV-IN1
(The actual location is not visible.) on and a red indicator lights when in the S-
VI AUDIO (R)
DE
standby mode (the indicator will not light O
Note:
■ TV/VIDEO, CH ( )/( ), VOL (+)/(–), and MENU on the main unit have the same functions as the same buttons
on the remote control. Fundamentally, this operation manual provides a description based on operation with the
remote control.
LC-20B2U
FRONT AND REAR CONTROL OPTIONS (Continued) REMOTE CONTROL
LC-20B2U
■ Before connecting a connection cord into the rear terminal, remove the POWER
back cover. Push in the tab and pull out the back cover carefully. DISPLAY
DISPLAY*1
SLEEP BRIGHT
SLEEP BRIGHT
MENU MENU/
■ To mount the cover, insert the 2 hooks on the bottom of the cover
into the cabinet and press on the upper part of the back cover until ]/[/</> (Cursor control)
the tab locks in place with a click. MUTE TV/VIDEO
MUTE TV/VIDEO
FLASHBACK
VOL(+)/(–) VOL CH
FLASHBACK*2
CH ( )/( )
1 2 3
4 5 6
Channel Select
7 8 9
MTS*3 MTS 0 100
Listening with Headphones
*1 Displays the receiving chan-
■ Plug the headphone mini-plug into the HEADPHONE jack located on the rear of the TV set. nel for 10 seconds.
*2 Returns to the previous
channel.
▼ On-screen display *3 Selects audio settings.
6
Rear terminal >
VOLUME
60
Headphones
Notes:
■ Headphones are not included in the supplied accessories.
■ No sound will be heard from the main unit speakers when a headphone mini-plug is connected into the
HEADPHONE jack.
CONNECTING WITH EXTERNAL DEVICES
You can enjoy picture and sound by connecting a VCR or a home video game system to the terminals
located on the rear of the TV set. Connecting a VCR, DVD player or a video camera (AV-IN1/2/COMPONENT)
When connecting an external device, turn off the power of the main unit first to prevent any possible
damage.
COMP
ONENT
Audio (R)
Y
PB
To audio/video
PR output terminal
* If your external device has an VCR
L
S-Video terminal, S-VIDEO AUDIO
R
connection is recommended. To component
HEAD
PHONE
R
input (Video)
POWE
* If your external device has an S-Video terminal, INPUT terminal
DC13V
To AV-IN2 terminal S-VIDEO connection is recommended.
To AV-IN1 terminal Y
PB
PR
7
Audio (L)
Audio (R)
• DVD, etc. To component
input (Audio)
DVD TUNER/BAND AUX 1 AUX 2 AUX 3
terminal SURROUND
ON/OFF
SURROUND
ON/OFF
DVD Player
To AV-IN1 terminal
AV
-IN
VID 1
* If your external device has a component EO
Notes:
■ PC connection is not possible.
■ For the cable, use a commercially available audio/video cord.
Notes:
■ Only connect audio/video signals to AV-IN1 and 2 terminals. Connecting other signals may result in a malfunction. ■ If your VCR (or other external devices) has an S-Video terminal, S-VIDEO connection is recommended. (Use an
■ AV-IN1 has 2 video input terminals: VIDEO and S-VIDEO. When you connect external devices to both terminals S-video cord.)
(and if you select AV-IN1), you can only view pictures from the S-VIDEO terminal. To view the picture from the ■ When you connect external devices to both S-VIDEO and VIDEO terminals (and if you select AV-IN1), you can
VIDEO terminal, do not connect any external device to the S-VIDEO terminal. only view pictures from the S-VIDEO terminal.
■ For more information about external device connections, see the manuals of your external devices. ■ You cannot view multiple or synthesized pictures by connecting two or more external devices. When connecting
an external device, use care to connect the video and audio cables to the corresponding terminals.
■ Do not connect antennas or headphones to AV-IN2.
LC-20B2U
CONNECTING WITH EXTERNAL DEVICES (Continued) SELECTING MENU ITEMS
LC-20B2U
HEAD PRESET
PHONE RETURN
POWER BR I GHTNESS [ BR I GHT ]
INPUT SELECT : ENTER : EX I T : MENU AUTO POWER OFF [ OFF ]
DC13V UPS I DE [ NORMAL ]
R I GHT / LEF T [ NORMAL ]
AV2 I N / OUT [ IN ]
Notes:
8
■ The TINT display only appears when
the color system is set to N358 or
SELECT : ADJUST : EX I T : MENU
Notes: N443.
■ AV2 has 2 OUT modes (see page 24). ■ The displayed items differ depending
on the setting conditions. CLOSED CAPT I ON
■ When using the S-Video input for AV-IN1, no video output will be made to the AV output terminal, but audio RETURN
output will be made for connection to external audio systems. ■ The selected item changes to yellow. MODE [ OFF ]
Note: ■ Items in magenta cannot be selected. DATA [ CH 1 ]
■ This product is factory set to comply
with the color system in the United
States (NTSC-N358). For Brazil
How to fix the cables (PAL-M), Argentina (PAL-N) and
Uruguay (PAL-N), set the color
SELECT : ADJUST : EX I T : MENU
system before using this product.
• Fix cables and cords with the attached cable ■ To return to the previous screen,
clamps so that they do not get caught when select RETURN.
■ You can adjust some settings with the
mounting the cover.
special buttons: SLEEP and BRIGHT I NPUT SECRET NO .
• Connect the cables and cords after fixing the
cable clamps (2 positions). – – – –
EX I T : MENU
SET UP
RETURN
BLUE SCREEN [ OFF ]
Cable clamps LANGUAGE
CH–SETT I NG
* The screen indications shown above are larger than actual for easy reading. SELECT : ADJUST : EX I T : MENU
LC-20B2U
Dimensions
24.6/626
15.9/403
15.1/384.5
11.9/301
18.7/474.5
14.9/379
3.7/95.1
2.4/60.5
ANT.
AV-IN1
VIDEO
AV-IN2/OUT
L
VIDEO
18.4/467.8
AUDIO
L R
AUDIO
R
S-VIDEO
COMPONENT
Y
PB
PR
L
AUDIO
R
HEAD
PHONE
POWER
INPUT
DC13V
2.9/72.9
9/229.4
(Unit: inch/mm)
9
LC-20B2U
Back cover 3
1 3
2
3
3
3
3
Table stand
Reinforcement angle
Operation PWB
5 Wire holder
6
6
P4004
6SC1201 P2003
Inverter-A
P6755
P2004
PWB 4
Main PWB 6 6
6 6
6 P6751
SC1202 SC2001
6 6
6 P3602
P3601
Jack PWB
P3701
P5001
6
P3702
P3401
6 6
Terminal PWB
6
SC3403
Inverter-B
P3501 P3500 PWB 6
6 6 P6555
P6551
6
P4005
10
LC-20B2U
Main PWB
Terminal PWB 10
Jack PWB
Inverter-A
PWB
14 11
Inverter-B
PWB
Operation PWB
13
12
11
LC-20B2U
15. Remove the two lock screws from the front of the LCD display unit and
the four lock screws from its back. Detach the shielding plate.
16. Detach the two reflection sheets.
17. Detach the top and bottom fluorescent lamps.
18. Remove the light guide plate.
19.Detach the diffusion sheet. 15
20. Detach the prism sheet and
reflection/deflection sheet.
15
15
15
17
Light Guide Plate
(PGiDM0065CEZZ)
18
Diffusion Sheet
19
Shielding Plate
16
Reflection Sheet-1
(PSHEP0250CEZZ)
Reflection Sheet-2
17 (PSHEP0251CEZZ)
Fluorescent Lamp (Bottom)
(KLMP-0111CEZZ)
20 Prism Sheet
LCD Display Unit
Reflection/deflection Sheet
12
LC-20B2U
[Description]
» The initialization of microcomputer is as follows.
» AV position, DAC data, G/A data, sound processor data, and video chroma data adjustment values are taken as
defaults.
(2)Adjustment mode
[Procedure]
Short-circuit TP2001 to GND, and turn on the power.
Or short-circuit TP2002 to GND, and turn on the power.
Or holding down the [TV/VIDEO] key and [MENU] key, turn on the main power, and simultaneously press the
(inspection process) [CH "] key and [VOL– ] key to change the mode to the adjustment mode.
[Description]
The manual adjustment or adjustment through communication with the automatic machine is performed.
(3)Inspection mode
[Procedure]
Holding down the [TV/VIDEO] key and [MENU] key, turn on the power.
[Description]
» In the ordinary menu select “VIDEO ADJUST” with the [CH] key, and decide with the [VOL] key. Then select
“PICTURE”, “TINT (only NTSC)”, “COLOR”, “BLACK LEVEL”, “SHARPNESS”, “RED-BLUE”, “GREEN” and
“COLOR SYSTEM” with the [CH] key, and decide with the [VOL] key. After that, adjust values with the [VOL] key.
» VOLUME, PICTURE, TINT (only NTSC), COLOR, BLACK LEVEL, SHARPNESS, RED-BLUE, GREEN change
as follows. Min. Center Max.
[Description]
User adjustment and other values are taken as defaults.
If TV is indicated as SETTING COMPLETE, setting has been completed.
13
LC-20B2U
4. Adjustments
Adjustment Adjusting conditions Adjusting method
2 Model and Inch Size 1. Go to the adjustment mode. 1. Select "MODEL" with [MENU] key
setup and adjust to "B2U" with [VOL+] or
(If E2PROM is replaced) [VOL-] key.
(IC2004) * The color of "MODEL" must be yellow.
2. Select "INCH SIZE" and adjust to
"20" with [VOL+] or [VOL-] key.
* The color of "INCH SIZE" must be
yellow.
3 Counter-bias adjustment 1. Receive a B/W channel. 1. Adjust "COM BIAS" to the darkest
2. Go to the adjustment mode. screen with [VOL+] and [VOL-] key.
3. Select the "COM BIAS" with * The color of "COM BIAS" must be
[MENU] key. yellow.
4 Checking and modifying 1. Go to the adjustment mode and 1. See if all the settings are as
the settings check the following settings. specified. If not, select an item in
(after replacing the » PRE SCALE FM/AM-M 17 question with [VOL+] or [VOL-] key
E2PROM) » PRE SCALE SCART 15 and adjust the setting as shown at
left.
» TV GEQ BAND 1 0.0 * An item selected will be highlighted
» TV GEQ BAND 2 0.0 in yellow.
» TV GEQ BAND 3 +1.0
» TV GEQ BAND 4 +0.5
» TV GEQ BAND 5 -1.5
» V SYNC DELAY 29
14
LC-20B2U
15
LC-20B2U
1
+B-ADJ 160
MODEL B2U
INCH SIZE 20
SYSTEM N358
NTSC PWM FREQ OCO
PAL PWM FREQ OBD
NTSC PWM DUTY 0
PAL PWM DUTY 0
TV GAIN OFF
ERROR NO RESET 0
V-CHIP 1
CANADIAN VCHIP OFF
B2U VER 1.xx
No
Note:
This model is equipped with the lamp error detection function
that detects the current flowing into the fluorescent lamp and
protects the backlight lamp drive circuit.
If a lamp error is detected, the microprocessor interrupts the
unit and the ERROR NO RESET setting will go up.
When the ERROR NO RESET setting has reached "5", the
microprocessor turns and keeps off the unit's power. To
resume the power, take the above procedure to clear the
ERROR NO RESET setting.
16
No picture
No TV and No VIDEO No S No
No picture No TV COMPONENT
VIDEO 1 1 or 2 VIDEO
at all output output
output output output
Are inputs Check IC801 Are inputs Check IC402 Are voltages Check the Are pins (2) Are pin
and outputs No and its and outputs No and its at Pins (6), No Check the Is input at Pin No
and (12) of No (67) of
(1) of IC402 line in
of IC801 as peripheral of IC402 as peripheral (7) and (9) of power line. IC7101 60th IC2001
as specified? question.
specified? parts. specified? parts. tuner as at “H”? at “H”?
specified?
Yes Yes Yes Yes
Yes
Are inputs Check Are input and Check Are Pins (2) Are Pins (65) Are inputs at Is input at
and outputs No IC1201 and output of No IC7001 and Is output at Check the and (4) of and (66) of Pins (71) and Pins (4), (5),
of IC1201 as its peripheral IC7001 as its peripheral Pin (19) of No tuner and its IC402 both at No IC2001 both (72) of IC801 (6) and (75)
specified? parts. specified? parts. tuner as peripheral “L” or Pins (4) at “L”or Pins as specified? of IC801 as
specified? parts. of IC402 at (66) of IC1201 specified?
Yes Yes “H”? at “H”? No
Yes No
17
Check LCD Are input and Check Yes Yes Check P5001,
panel voltage No SY line, SC Check J3404,
output of IC7202 and Check the
and
Is input at Pin No
Check IC402 line and J3405, J3406,
IC7202 as its peripheral (1) of IC402 line in Check the
waveform. and its peripheral DVD-Y line,
specified? parts. as specified? question. line in
peripheral parts. PB line, PR
question. line and
Yes parts.
Yes peripheral
Check IC801, parts.
Is input at Pin No Are Pins (2) Are Pins (65)
AV1 line and
(73) of IC801 and (4) of No and (66) of
their
as specified? IC402 at “H” IC2001 at “H”
peripheral
parts. and “L” and “L”
respectively? respectively?
Yes Yes
Check IC402
Check the
and its
TROUBLE SHOOTING TABLE (Continued)
line in
peripheral
question.
parts.
LC-20B2U
No picture and sound Fluorescent lamp
LC-20B2U
18
load of T3701. and check the oscillation
waveform again.
No color
No No
Are input and Check the Are outputs at Check IC3501, Check Q3201,
No Check IC3304 No Is input at Pin No
output of headphone and Pins (14) and IC3304 and its Q3202 and
and its (67) of IC3304
IC3304 as its peripheral (15) of IC3501 peripheral their peripheral
peripheral parts. as specified?
specified? parts. as specified? parts. parts.
19
Are outputs at Check IC3301, Check IC3304,
Pins (1) and (7) No IC3303 and Check the line X3301 and
of IC3301/ their peripheral in question. their peripheral
IC3303 as parts. parts.
specified?
Yes
Yes
TROUBLE SHOOTING TABLE (Continued)
Check the
speakers and
their peripheral
parts.
LC-20B2U
LC-20B2U
CHASSIS LAYOUT
MAIN Unit (Side A) R/C RECEIVER Unit
H
OPERATION Unit
E
INVERTER-B Unit
TERMINAL Unit
1 2 3 4 5 6 7 8 9 10 11 12
20 21
LC-20B2U
BLOCK DIAGRAM
H I2C TERMINAL UNIT JACK UNIT INVERTER-A UNIT INVERTER-B UNIT
L1, R1 AV 1
TUNER TV-V V1 S-VIDEO INVERTER HOT INVERTER HOT
TU3201 SIF SY, SC INPUT T6751, T6752 LAMPS T6551, T6552 LAMPS
Q6751, Q6752 Q6551, Q6552
V2/VO Q6755 Q6555
COLD COLD
AV 2 AUDIO VIDEO
INPUT IN/OUT IN/OUT V2
G OUTPUT SWITCH SWITCH VO
IC3501 Q3501-Q3505
Q3500 LAMP
CHECK
SY, SC MAIN UNIT
Y, PB, PR I2C
COMPONENT
INPUT DL, DR Y and C
SWITCH 3D Y/C
SYOUT, IC7101 YO, CO SEPARATION
AUDIO AUDIO AUDIO SCOUT Q7101 IC7001
DECODER FILTER AM PLIFIER TV-V Q7102 IC7002
F (MSP) VIDEO V
IC3301 IC3305 V1 IC7003
IC3304 IC3303 SWITCH
V2 IC402 IC7004
Q7001-Q7010
DC IN
DC13V I2C
VIDEO SY
REGULATOR
SWITCH IC7102
IC7202 IC7701
Y
REGULATOR
E IC3702
I2C
DC/DC 38V 31V VIDEO
Q3707 6dB AM P
T3701 IC7201
Y, C
IC3701 16V 29V
Q3700 Q3704 GATE
Q3701 LCD CONTROL
Q3702 CONTROLLER IC1203 LCD
9V 14V Y, PB, PR IC1201 PANEL
VIDEO IC1204
Q3705 DECODER IC1205
D (VPC)
5V 8V SYNC IC801 FIFO
HEAD SEPARATER. BUFFER IC1202
Q3706 PHONE Q401
IC401
JACK
-8V
3.3V REG.
IC702
C
GRADUATION
SP-L SP-R POWER FOR
CVI N CK, VD, HD, OSD-RGB LCD
IC1102-IC1108
CSYNC WIRE IC1110
DAC
L_ERR IC1101
MPU
IC2001 BUS-SWITCH COMMON
IRMI, POWOUT, TIMED I2C IC1109
IC2003
Q1101
B KEY1, KEY2 Q1102
E2PROM
IC2004
LED R/C
D4014 POWER CONTROL
RECEIVE SWITCH
D4015 R KEYS
5V REG. RESET
IC701 IC2002
R/C RECEIVER UNIT OPERATION UNIT
A
1 2 3 4 5 6 7 8 9 10 11 12
22 23
LC-20B2U
24
LC-20B2U
SCHEMATIC DIAGRAM
Ë OPERATION and R/C RECEIVER Unit
H
OPERATION
R/C RECEIVER
D
1 2 3 4 5 6
25
LC-20B2U
Ë MAIN Unit-1/5
1 2 3 4 5 6 7 8 9 10 11 12
26 27
LC-20B2U
Ë MAIN Unit-2/5
1 2 3 4 5 6 7 8 9 10 11 12
28 29
LC-20B2U
Ë MAIN Unit-3/5
1 2 3 4 5 6 7 8 9 10 11 12
30 31
LC-20B2U
Ë MAIN Unit-4/5
1 2 3 4 5 6 7 8 9 10 11 12
32 33
LC-20B2U
Ë MAIN Unit-5/5
1 2 3 4 5 6 7 8 9 10 11 12
34 35
LC-20B2U
Ë TERMINAL Unit-1/2
1 2 3 4 5 6 7 8 9 10 11 12
36 37
LC-20B2U
Ë TERMINAL Unit-2/2
1 2 3 4 5 6 7 8 9 10 11 12
38 39
LC-20B2U
Ë JACK Unit
1 2 3 4 5 6
40
LC-20B2U
1 2 3 4 5 6
41
LC-20B2U
G
R/C Receiver Unit (Component Side)
1 2 3 4 5 6
42
LC-20B2U
1 2 3 4 5 6
43
LC-20B2U
A
Main Unit (Side-A)
1 2 3 4 5 6
44
LC-20B2U
A
Main Unit (Side-B)
1 2 3 4 5 6
45
LC-20B2U
1 2 3 4 5 6
46
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
★ MARK: SPARE PARTS-DELIVERY SECTION ★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
COILS DUNTKA430DE01
L6752 RCiLC0142CEZZ J Coil AG INVERTER-B UNIT
L6753 RCiLC0142CEZZ J Coil AG
TRANSISTORS
TRANSFORMERS Q6551 VSFZT1053A/-1 J FZT1053A AG
å T6751 RTRNZ0798CEZZ J Transformer AM Q6552 VSFZT1053A/-1 J FZT1053A AG
å T6752 RTRNZ0798CEZZ J Transformer AM Q6555 VS2SA1037KQ-1 J A1037KQ AA
å T6753 RTRNZ0798CEZZ J Transformer AM
COILS
L6552 RCiLC0142CEZZ J Coil AG
L6553 RCiLC0142CEZZ J Coil AG
47
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
TRANSFORMERS TRANSISTORS
å T6551 RTRNZ0798CEZZ J Transformer AM Q401 VS2SC2712Y/-1 J C2712Y AB
å T6552 RTRNZ0798CEZZ J Transformer AM Q701 VS2SA1162Y/-1 J A1162Y AB
å T6553 RTRNZ0798CEZZ J Transformer AM Q702 VSDTC144EE/-1 J C144EE AA
Q703 VS2SA1162Y/-1 J A1162Y AB
CAPACITORS Q1101 VS2SA1729//-1 J A1729 AF
[M-Poly. .…Metalized Polypro Film] Q1102 VS2SC4520//-1 J C4520 AE
C6552 RC-FZ0175CEZZ J 0.15 100V M-Poly. AG Q1201 VSDTC144EE/-1 J C144EE AA
C6559 VCKYCY1CB333K J 0.033 16V Ceramic AA Q1202 VSDTC144EE/-1 J C144EE AA
C6560 VCKYCY1CB333K J 0.033 16V Ceramic AA Q2004 VSDTC144EE/-1 J C144EE AA
C6561 VCEAPW1CN477M J 470 16V Electrolytic AE Q2050 VSDTC144EE/-1 J C144EE AA
C6562 VCEAPW1CN477M J 470 16V Electrolytic AE Q7001 VS2SA1037KQ-1 J A1037KQ AA
C6565 RC-FZ0175CEZZ J 0.15 100V M-Poly. AG Q7002 VS2SC2412KQ-1 J C2412KQ AA
Q7003 VS2SA1037KQ-1 J A1037KQ AA
RESISTORS Q7004 VS2SC2412KQ-1 J C2412KQ AA
R6551 VRS-TW2ED332J J 3.3k 1/4W Metal Oxide AB Q7005 VS2SA1037KQ-1 J A1037KQ AA
R6552 VRS-TW2ED332J J 3.3k 1/4W Metal Oxide AB Q7006 VS2SA1037KQ-1 J A1037KQ AA
R6553 VRS-TX2HF000J J 0 1/2W Metal Oxide AA Q7007 VS2SA1037KQ-1 J A1037KQ AA
R6554 VRS-TX2HF000J J 0 1/2W Metal Oxide AA Q7008 VS2SA1037KQ-1 J A1037KQ AA
R6555 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide AA Q7009 VS2SA1037KQ-1 J A1037KQ AA
R6556 VRS-TQ2BD333J J 33k 1/8W Metal Oxide AA Q7010 VS2SA1037KQ-1 J A1037KQ AA
R6557 VRS-TX2HF000J J 0 1/2W Metal Oxide AA Q7101 VS2SC2712Y/-1 J C2712Y AB
R6558 VRS-TQ2BD000J J 0 1/8W Metal Oxide AA Q7102 VS2SC2712Y/-1 J C2712Y AB
R6559 VRS-TX2HF000J J 0 1/2W Metal Oxide AA
R6560 VRS-TX2HF000J J 0 1/2W Metal Oxide AA DIODES
R6561 VRS-TQ2BD000J J 0 1/8W Metal Oxide AA D1101 VHD1SS250//1E J Diode AB
R6562 VRS-TQ2BD000J J 0 1/8W Metal Oxide AA D1201 VHDDAN222//-1 J Diode AA
R6563 VRS-TX2HF000J J 0 1/2W Metal Oxide AA D2001 VHDDAN222//-1 J Diode AA
R6564 VRS-TX2HF000J J 0 1/2W Metal Oxide AA D7701 VHDDAN202K/-1 J Diode AB
48
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
49
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
50
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
51
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
52
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
53
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
54
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
DUNTKA5710DE01
R/C RECEIVER UNIT CABINET PARTS LOCATION
1 CCABA2434CE01 J Front Cabinet Ass’y BK
TRANSISTORS 1-1 Not Available – Front Cabinet —
Q4003 VSDTC144EE/-1 J C144EE AA 1-2 GCOVA2004CEZZ J LED Decoration Cover AE
Q4004 VSDTC144EE/-1 J C144EE AA 1-3 PSPAG0393CEUZ J Spacer, x4 AB
Q4007 VSUMG4N++++-1Y J UMG4N++++ AB 1-4 PSPAG0394CEUZ J Spacer, x4 AC
1-5 PSPAG0395CEUZ J Spacer, x4 AB
DIODES 1-6 PSPAH0678CEZZ J Spacer, x2 AA
D4012 RH-EX0879CEZZ J Zener Diode AD 1-7 PSPAH0699CEUZ J Spacer, x2 AD
D4013 RH-EX0879CEZZ J Zener Diode AD 1-8 PSPAH0700CEUZ J Spacer, x2 AD
D4014 RH-PX0421CEZZ J LED, POWER AD 1-9 QCNW-6019CEZZ J Connecting Cord AB
D4015 RH-PX0421CEZZ J LED, SLEEP AD 1-10 QCNW-6020CEZZ J Connecting Cord AB
D4022 RH-EX0879CEZZ J Zener Diode AD 1-11 VSP0050PBP68S J Speaker, x2 AR
1-12 XEBSD40P10000 J Screw, x8 AA
CAPACITOR
C4018 RC-KZ1025CEZZ J 1.0 10V Ceramic AB 2 CCABB2321CE01 J Rear Cabinet Ass’y BD
2-1 Not Available – Rear Cabinet —
RESISTORS 2-2 HiNDP5835CESA J Model Indication Label AG
R4021 VRS-CY1JF101J J 100 1/16W Metal Oxide AA (without "NOM" mark)
R4023 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA 2-2 HiNDP5860CESA J Model Indication Label
R4024 VRS-CY1JF471J J 470 1/16W Metal Oxide AA (with "NOM" mark)
R4029 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA 2-3 TCAUH3096CESA J Caution Label AE
R4030 VRS-CY1JF472J J 4.7k 1/16W Metal Oxide AA
3 CDAi-1122CE04 J Stand BQ
MISCELLANEOUS PARTS 3-1 Not Available – Stand Base —
P4005 QPLGN0564TAZZ J Plug, 5-pin AC 3-2 GCOVA1945CESA J Handle Cover AK
RMC4002 RRMCU0239CEZZ J R/C Receiver AG 3-3 GDAi-1123CESA J Stand Joint AQ
3-4 GDAi-3049CESA J Base Joint AQ
3-5 GDAi-3053CESA J Stand AQ
3-6 GLEGG9093CEZZ J Foot, x6 AC
3-7 JHNDP0103CESA J Stand Handle AX
3-8 LANGG0114CEFW J Fixing Metal, x2 AE
3-9 LX-BZ3441CEFN J Screw, x1 AD
3-10 MHNG-3034CEFW J Hinge, Left AV
3-11 MHNG-3035CEFW J Hinge, Right AV
3-12 MHNG-3036CEFW J Hinge, Side AX
3-13 PSPAT0079CEZZ J Spacer, x2 AC
3-14 PSPAZ0415CEZZ J Spacer, x2 AB
3-15 XCBSD50P25000 J Screw, x4 AB
3-16 XCSSN50P25000 J Screw, x4 AB
3-17 XESSD40P14000 J Screw, x8 AB
3-18 XESSN40P10000 J Screw, x8 AB
3-19 XWHSN50-16120 J Washer, x4 AB
55
LC-20B2U
4-3
4-1 4-2
4
4-4 26
18
4-5 17
G
37 19
1-12 OPERATION Unit
18
1-4 A
1-3 B
23
1-9 20
1-8 23
1-11
F
1-5 1-7
22
1-3
5
1-4
1-8
1-3 1-6 31
1-4
1-7
1-5
E
33
1-12 INVERTER-A 35
1-6 Unit
1-10 1-3
INVERTER-B
1-11 Unit MAIN Unit
35 36 36
1-1 36
6
35 35
D 29
32 35
37 JACK 36
23 Unit
R/C RECEIVER Unit
1
1-2
21 35
B 27
C
7
A TERMINAL Unit
10
24
9
30
12
15
11 16
B
14
13
9
8
17
1 2 3 4 5 6 7 8 9 10
56
LC-20B2U
3-7
3-2
3 28
3-11
3-17
3-8
3-18 3-13 3-3
3-13 3-8
3-14
3-10
3-12
3-17 3-17
2 38 3-14
2-2
38 38 3-1
34
3-9
3-19 3-6
3-15
25
38
10 11 12 13 14 15 16 17 18 19
57
LC-20B2U
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
58
LC-20B2U
Operation Manual
Cable Clamp (2 pcs.)
★ Dry Battery (2 pcs.)
AC Adapter
AC Cord
Antenna Cable
Wireless Remote Control
★ Buffer Material
(Top)
★ Polyethylene Bag
★ Buffer Material
(Bottom)
★ Packing Case
59
LC-20B2U
SHARP CORPORATION
D Japan P JapanTQ1148-S AV Systems Group
Jun. 2001 Printed in Japan Quality & Reliability Control Center
NA. KG Yaita, Tochigi 329-2193, Japan
60