Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Stannous
Chloride
Stannous
Chloride
Physical
State
Disc Materials
Condition
Solid
Seat/Disc Materials
DI
NDI
AL
BR
316
SS
A*
Coating
Solid
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
<10%,
<140F
A*
<10%,
<140F
A*
Since no conditions are specified for Disc Materials, one should assume nylon covered ductile iron is the recommended
material for content temperatures up to 140F, and 316 stainless steel above 140F. Of course, Nylon 11 may actually be
suitable for temperatures much greater than 140F, as stated previously (see Technical Bulletin 1009, Nylon Coatings
Physical/Chemical Resistance Properties for additional information).
d) Disc Materials and Seat/Disc Materials Under each grouping, the primary materials offered by Bray have been
graded for their suitability to the media and conditions stated. The grading system is as follows:
A Recommended, generally little or minor effect based on valve usage experience and recommendations from
suppliers
B May sometimes be used depending upon the conditions of application such as concentration and temperature.
Testing is recommended before full-scale usage.
N Not recommended for usage.
Blank Insufficient evidence available
e) Recommended Materials for Disc and Seat/Disc For each media and condition, we have placed an asterisk by the
disc and seat material recommended by Bray. The material given an asterisk depends on two factors:
1) The material is rated A for compatibility with the media conditions;
2) It is the most economical Bray material offered as a disc in combination with the most economical seat material.
For example:
Corrosive
Media
Carbon
Tetrachloride
Disc Materials
Physical
State
Condition
DI
NDI
AL
BR
316
SS
Liquid
<75F
A*
Seat/Disc Materials
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
NBR
A*
If the carbon tetrachloride for your media is <75F, you must choose a 316 disc, not AB, because Bray does not offer an
AB disc with a Teflon seat. If the temperature is >75F, one should not assume we do not have a suitable valve material
code. Remember, Bray carries EPDM, BUNA-N, and Teflon molded disc-stems, thus one should select a Teflon disc stem
and a Teflon seat for this application.
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
f) Coating of Disc Materials When a disc coating is recommended, it will be noted in this column. The most economical
Bray coating material will be noted with an asterisk. An example of reading the Material Selection Guide with a
recommended disc coating is as follows:
Corrosive
Media
Disc Materials
Seat/Disc Materials
Physical
State
Condition
DI
NDI
AL
BR
316
SS
Liquid
<5%
A*
Liquid
<5%
A*
Liquid
<37%
Hydrochloric
Acid
Hydrochloric
Acid
Hydrochloric
Acid
Coating
Condition
<15%,
<75F
<37%,
<75F
A*
EPDM
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
If one has a concentration of Hydrochloric Acid less than 5% at any temperature, Bray recommends an NDI disc and
EPDM seat. If the condition is a concentration less than 37% and less than 75F, then again an EPDM disc stem and seat
are recommended. Finally, if the condition is one that is over 15% concentration at a temperature of 75F or more, or the
concentration is 37% or more at any temperature, Bray recommends a Series 22/23 Teflon disc stem and seat, or a disc
an stem that has EPDM coating.
Material
Ethylene Propylene
ASTM Designation
Bray Reference
Temperature Rating
Food Grade
EPDM
EPDM
250F to -40F
Yes
NBR
Buna-N
212F to 0F
Yes
Teflon Lined
Ethylene Propylene
Diene Monomer
PTFE
250F to -20F
Yes
Specific Reference
Ductile Iron
Aluminum Bronze
ASTM B148-954
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
FluoroElastomer
FKM
FKM
400F to 0F
No
Disc Materials
Corrosive
Media
Physical
State
Acetaldehyde
Liquid
Acetaldehyde
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
A*
Liquid
Acetamide
Solid
Acetamide
Solid
Condition
Acetic Acid
Liquid
Acetic Acid
Liquid
Acetic Acid
<75F
Coating
Condition
<100F
A*
PTFE
A*
<100%,
<160F
A*
A*
<100%,<160F
A*
<100%,
<160F
Liquid
<100%,<160F
A*
<50%,
<70F
A*
Acetic Acid
Liquid
<100%,<160F
A*
Dilute,
<200F
A*
Acetic Acid
Liquid
<100%,<160F
A*
A*
Acetic Acid
Liquid
<100%,<160F
A*
<90%,
<250F
A*
Acetic Acid
Liquid
A*
PTFE
<90%,
<250F
A*
A*
Acetic Acid
Liquid
A*
PTFE
Acetic Acid
Liquid
A*
PTFE
<50%,
<70F
A*
Acetic Acid
Liquid
A*
PTFE
Dilute,
<200F
A*
Acetic Acid-Glacial
Liquid
A*
PTFE
<160F
A*
Acetic Acid-Glacial
Liquid
A*
PTFE
A*
Acetic Acid-Vapors
Gas
A*
PTFE
A*
Acetic Acid-Vapors
Gas
A*
PTFE
A*
Acetic Anhydride
Liquid
A*
A*
Acetic Anhydride
Liquid
A*
<70F
A*
Acetone
Liquid
A*
<200F
A*
Acetone
Liquid
A*
<130F
A*
Acetone
Liquid
A*
A*
Acetone
Liquid
A*
<200F
A*
Acetone
Liquid
A*
<130F
A*
Acetone
Liquid
A*
A*
Acetophenone
Liquid
A*
A*
Acetyle Acetone
Liquid
A*
A*
Acetyle Chloride
Liquid
A*
A*
<75F
<75F
<75F
<75F
<70F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AIBR
316
SS
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
Acetylene
Gas
A*
Acetylene
Gas
A*
Acetylene
Gas
<75F
A*
A*
Acetylene
Gas
<75F
A*
A*
A*
NBR
A*
A*
AIBR
NBR
A*
NBR
A*
<160F
<160F
UHMWPE
Acrylic Latix
Liquid
Acrylonitrile
Liquid
Acrylonitrile
Liquid
A*
Acrylonitrile
Liquid
A*
<160F
NBR
A*
Acrylonitrile
Liquid
<160F
NBR
A*
A*
A*
A*
Air
<160F
<160F
Gas
A*
A*
A*
A*
A* FKM
A*
A*
Alum-Chrome
(see Chromium
Potassium
Sulfate)
Alum-Others
Alum-Potassium
(see Aluminum
Potassium
Sulfate)
Alumina
(activated,
abrasive)
Aluminum
Chloride
Solid
<150F
Solid
Solid
<150F
A*
UHMWPE
A*
EPDM
A* FKM
<25%,
<160F
A*
A*
A*
A*
EPDM
<25%,
<160F
A*
A*
A*
Solid
A*
Aluminum
Hydroxide
Solid
A*
Aluminum
Hydroxide
Solid
A*
Aluminum
Hydroxide
Solid
A*
A*
Aluminum
Nitrate
Solid
A*
A*
Aluminum
Nitrate
Solid
A*
A*
Aluminum
Phosphate
Aluminum
Potassium
Sulfate
Aluminum
Potassium
Sulfate
Aluminum
Sulfate
Solid
A*
A*
Solid
A*
Solid
A*
A*
A*
A*
Aluminum
Chloride
Solid
Aluminum
Chloride
Solid
Aluminum
Chloride
Solid
Aluminum
Fluoride
Solid
<25%,
<160F
<25%,
<160F
<25%,
<150F
A*
UHMWPE
<100F
<100F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Amines
Liquid
Amino Acids
Liquid
Disc Materials
Condition
<150F
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
A*
A*
Coating
Condition
Ammonia Gas
Gas
A*
100%,
<140F
Ammonia Gas
Gas
A*
<65%,<80F
Ammonia,
Anhydrous
Gas
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A
A
A*
A*
A*
A*
A*
A*
A*
Ammonia, Liquid
Liquid
Ammonia,
Solutions
Ammonium
Bicrbonate
Liquid
A*
Solid
A*
A*
Ammonium
Bifluoride
Liquid
A*
Ammonium
Bisulfate
Solid
A*
Ammonium
Bisulfite
Ammonium
Bisulfite
Solid
Solid
A*
PTFE
A*
PTFE
Ammonium
Bisulfite
Solid
<160F
A* FKM
Ammonium
Bisulfite
Ammonium
Bromide
Solid
<160F
A* FKM
Ammonium
Carbonate
Solid
A*
Ammonium
Chloride
Solid
A*
Ammonium
Dichromate
Solid
A*
Ammonium
Diphoshate
Solid
A*
EPDM
Ammonium
Formate
Solid
A*
PTFE
Ammonium
Hydroxide
Ammonium
Hydroxide
Liquid
A*
<30%,<250F
Liquid
A*
<100F
A*
Ammonium Nitrate
Solid
<20%,<290F
A*
Ammonium Nitrate
Solid
<25%,<160F
A*
A*
Ammonium Nitrate
Solid
<25%,<160F
A*
Ammonium Nitrate
Solid
<200F
A*
Ammonium Nitrate
Solid
<200F
A*
100%, <75F
Solid
Ammonium Nitrate
Solid
Ammonium Nitrate
Solid
<20%,<290F
<25%,<160F
<160F
<160F
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
<160F
A*
<160F
A*
<25%,<150F
<160F
<160F
A*
PTFE
UHMWPE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AIBR
316
SS
Coating
A* PTFE
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
Ammonium
Nitrate
Solid
Ammonium
Nitrate
Solid
A*
Ammonium
Persulfate
Solid
A*
Ammonium
Phosphate
Solid
<25%,
<150F
A*
A*
Ammonium
Phosphate
Ammonium
Phosphate,
Monobasic
Ammonium
Sulfate
Solid
<25%,
<150F
A*
Solid
A*
A*
Solid
A*
A*
Ammonium
Sulfide
Solid
A*
A*
Ammonium
Thiocyanate
Solid
Ammonium
Thiocyanide
Solid
A*
EPDM
Ammonium
Thiocyanide
Solid
A*
EPDM
Ammonium
Thiocyanide
Solid
A* FKM
Ammonium
Thiocyanide
Solid
A* FKM
Ammonium
Thiosulfate
Solid
A*
Amyl Acetate
Liquid
A*
A*
Amyl Alcohol
Liquid
A*
A*
Amyl Borate
Liquid
A* PTFE
Amyl Borate
Liquid
A* PTFE
Amyl Chloride
Liquid
Amyl Napthalene
<150F
A*
EPDM
A*
A*
<160F
A*
<160F
A*
A*
A*
A*
A*
A*
A*
Liquid
A*
A*
Amyl Napthalene
Liquid
A*
A*
Analine Dye
Liquid
A*
A*
Aniline
Hydrochloride
Solid
A* PTFE
A*
Aniline
Hydrochloride
Solid
A* PTFE
<160F
A*
Animal Fats
Liquid
A*
<140F
A*
Animal Fats
Liquid
A*
<140F
A*
A*
A*
A*
A*
A*
Animal Fats
Animal Fats
Antimony
Trichloride
Liquid
Liquid
Liquid
A*
<140F
<140F
<160F
<70F
A* PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AIBR
316
SS
Coating
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
<140F
A*
A*
Condition
Antimony
Trichloride
Solid
Aqua Regia
(Sulfuric-Nitric)
Liquid
Aqua Regia
(Sulfuric-Nitric)
Liquid
Arsenic Acid
Solid
A*
<80%,
<212F
N
A*
A*
A*
A*
<140F
A*
<160F
A*
A* PTFE
A* PTFE
A* PTFE
A*
<80%,
<175F
<140F
A*
<140F
<140F
A*
Liquid
Arsenic Acid
Solution
Liquid
Asphalt
Liquid
<75F
Barium Nitrate
Solid
<75F
A*
A*
Barium Nitrate
Solid
<30%,
<212F
A*
Barium
Carbonate
Solid
Barium Chloride
Solid
<25%,
<160F
Barium Cyanide
Solid
Barium Cyanide
Solid
Barium Cyanide
Solid
Barium Cyanide
Solid
Arsenic Acid
Solid
Arsenic Acid
Solution
Liquid
Arsenic Acid
Solution
Liquid
Arsenic Acid
Solution
A* PTFE
A* PTFE
A*
UHMWPE
Baking Soda
(See Sodium
Bicarbonate)
A*
A*
<140F
A*
EPDM
<140F
A*
EPDM
A* FKM
A* FKM
A*
A*
A*
A*
A*
<140F
A*
<25%,
<160F
<140F
Solid
<50%,
<75F
A*
<160F
A*
Barium
Hydroxide
Solid
<50%,
<200F
A*
<160F
A*
Barium Sulfate
Solid
A*
A*
Barium Sulfide
Solid
A*
A*
Beer-Breweries
Liquid
A*
A*
Beet Sugar
Liquors
Liquid
A*
A*
Benzaldehyde
Liquid
A*
A*
A*
A*
A*
A*
A*
Barium
Hydroxide
Benzaldehyde
Benzaldehyde
Benzaldehyde
Liquid
Liquid
Liquid
<25%,
<150F
<160F
<80F
A* PTFE
<160F
<160F
A* PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Corrosive
Media
Physical
State
Benzaldehyde
Liquid
Benzaldehyde
Liquid
Benzaldehyde
Liquid
Benzaldehyde
Conditio
n
DI
NDI
AIBR
316
SS
<160F
A*
<160F
A*
Liquid
<80F
A*
Benzaldehyde
Liquid
<80F
A*
Benzene
Liquid
A*
Benzenesulfonic
Acid
Solid
Benzenesulfonic
Acid
Solid
<125F
A*
Benzenesulfonic
Acid
Solid
<125F
A*
Benzenesulfonic
Acid
Solid
Benzoic Acid
Liquid
<170F
A*
Benzoic Acid
Liquid
<170F
A*
Benzoic Acid
Liquid
<170F
A*
Benzoic Acid
Liquid
Benzoic Acid
Liquid
Benzoic Acid
Liquid
Benzol
Liquid
Benzoyl Chloride
Liquid
A*
Benzoyl Chloride
Liquid
Benzyl Alcohol
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
<80F
A*
<80F
A*
A*
<160F
A*
<80F
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
PTFE
A*
A*
PTFE
A*
A*
PTFE
A*
A*
A*
A*
A*
A*
Liquid
A*
A*
Benzyl Benzoate
Liquid
A*
A*
Benzyl Chloride
Liquid
A*
Bismuth Carbonate
(Dry)
Black Sulfate
Liquor (See Sodium
Bisulfate)
Black Sulfate
Liquor (See Sodium
Bisulfate)
Blast Furnace Gas
(Clean)
Solid
A*
A*
Gas
A*
A*
Gas
A*
A*
<75F
A*
Coating
A*
PTFE
Condition
A*
PTFE
<125F
A*
PTFE
<125F
<170F
<170F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Corrosive
Media
Physical
State
Bleaching Solutions
Liquid
Bleaching Solutions
Seat/Disc Materials
Condi
tion
DI
NDI
AIBR
316
SS
Coating
<180F
A*
EPDM
Liquid
Bleaching Solutions
Liquid
Bleaching Solutions
Liquid
A*
<180F
A* PTFE
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
<180F
A*
<180F
A*
A*
A*
A*
A*
Condition
A* PTFE
A*
EPDM
UHMWPE
Solid
Boric Acid
Solid
<100F
A*
Boric Acid
Solid
<212F
A*
A*
Boric Acid
Solid
<100F
A*
A*
Boric Acid
Solid
<212F
A*
A*
Brandy
Liquid
A*
A*
Brine
Liquid
A*
A*
Brine - Chlorinated
Liquid
A*
A*
Brine - Saturated
Liquid
A*
A*
Bromine - Anhydrous
Solid
A*
Bromine - Anhydrous
Solid
A*
Bromine - Wet
Liquid
A*
Bromine - Wet
Liquid
A*
Bromine - Wet
Liquid
<110F
A*
Bromine - Wet
Liquid
<110F
A*
Bromobenzene
Liquid
A*
Bromobenzene
Liquid
A*
Solid
A*
Butadiene
Liquid
A*
A*
Butadiene
Liquid
A*
A*
Butadiene
Liquid
A*
A*
A*
A*
A*
A*
Butadiene
Butane
Butane
Liquid
Gas
Gas
<110F
<110F
100%,
<75F
100%,
<75F
<180F
<180F
A*
A*
<160F
<160F
A* PTFE
A* PTFE
A* FKM
A* PTFE
A* FKM
A* PTFE
<160F
A*
UHMWPE
<225F
<225F
<75F
<180F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
Condition
DI
NDI
AIBR
316
SS
<180F
A*
Coating
Condition
Butane
Gas
Butane
Gas
A*
Butane
Gas
A*
<75F
A*
Butane
Gas
A*
<180F
A*
Butter
Liquid
A*
A*
Buttermilk
Liquid
A*
A*
Butyl Acetate
Liquid
A*
A*
Butyl Acetate
Liquid
A*
PTFE
A*
Butyl Acetate
Liquid
A*
PTFE
A*
Butyl Alcohol
Liquid
A*
A*
Butyl Alcohol
Liquid
A*
A*
Butyl Alcohol
Liquid
A*
<80F
A*
Butyl Alcohol
Liquid
A*
<80F
A*
Butyl Amine
Liquid
A*
Butyl Carbitol
Liquid
A*
A*
Butyl Cellosolve
Liquid
A*
A*
Butyl Chloride
Liquid
A*
Butyl Ether
Liquid
A*
A*
Butyl Oleate
Liquid
A*
A*
Butyl Stearate
Solid
A*
A*
Butylene (Gas)
Gas
A*
A*
Butylene (Gas)
Gas
A*
A*
Butyraldehyde
Liquid
A*
A*
A*
A*
A*
A*
A*
A*
A*
<75F
<75F
A*
<75F
A*
Butyric Acid
Liquid
Butyric Acid
Liquid
<5%,
<150F
Butyric Acid
Liquid
Liquid
Cadmium
Cyanide (Dry)
Calcium Acetate
A*
A*
Solid
Solid
A*
<5%,
<150F
Butyric Acid
<160F
<140F
<30%,
<100F
A*
PTFE
A*
PTFE
<30%,
<100F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Seat/Disc Materials
Corrosive
Media
Physical
State
Calcium Bisulfate
Solid
Calcium Bisulfite
Liquid
Calcium Bisulfite
Liquid
A*
Calcium Bisulfite
Liquid
A*
Calcium Bisulfite
Liquid
Calcium Carbonate
Solid
A*
Calcium Carbonate
Solid
A*
Calcium Chlorate
Solid
A*
Calcium Chloride
Solid
Calcium Chloride
Solid
A*
Calcium Chloride
Solid
A*
PTFE
Calcium Chloride
Solid
A*
PTFE
Calcium Chloride
Solid
<25%,
<150F
A*
Calcium Chloride
Solid
<25%,
<150F
A*
Calcium
Fluophosphate
Solid
Calcium
Fluophosphate
Solid
Calcium Hydroxide
(Lime)
Solid
Calcium Hydroxide
(Lime)
Calcium
Hypochlorite
Calcium
Hypochlorite
Conditio
n
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
<30F
A*
<25%,
<150F
A*
<25%,
<150F
A*
<30F
A*
A*
PTFE
A*
A*
PTFE
A*
<20%,
<212F
A*
A*
Solid
<75F
A*
A*
Solid
<25%,
<150F
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
A*
Coating
Condition
<160F
<25%,
<150F
Solid
<25%,
<150F
Calcium
Hypochlorite
Solid
<25%,
<150F
Calcium Nitrate
<160F
<140F
A*
PTFE
<160F
<25%,
<150F
A*
Solid
A*
Calcium Nitrate
Solid
A*
Calcium Sulfate
Solid
A*
A*
Calcium Sulfate
Solid
A*
A*
Calcium Sulfide
Solid
A*
Cane Sugar
Liquors
Liquid
A*
A*
A*
Carbamate
Carbamate
<10%,
<75F
A*
N
A*
A*
A*
<50%,
<140F
<10%,
<80F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Corrosive
Media
Physical
State
Carbolic Acid
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
Liquid
A*
Carbolic Acid
Liquid
Carbon Bisulfide
Liquid
A*
Carbon Dioxide
- Gas, Dry
Gas
A*
Carbon Dioxide
- Liquid, Wet
Liquid
Carbon
Disulfide
Liquid
A*
Carbon
Disulfide
Liquid
A*
Carbon
Disulfide
Liquid
<140F
A*
Carbon
Disulfide
Liquid
<140F
A*
Carbon
Monoxide
Gas
<100F
A*
Carbon
Monoxide
Gas
<100F
A*
Condition
Coating
Condition
<140F
<140F
<140F
<100F
Carbon
Tetrachloride
Liquid
NDI
A*
PTFE
Carbon
Tetrachloride
Liquid
NDI
A*
PTFE
Carbon
Tetrachloride
Liquid
<75F
A*
Carbon
Tetrachloride
Liquid
<75F
A*
Carbonated
Water
Liquid
Carbonic Acid
Liquid
NDI
A*
Carbonic Acid
Liquid
NDI
A*
Carbonic Acid
Liquid
<100F
A*
Carbonic Acid
Liquid
<100F
A*
<50%
<50%
A*
A*
<175F
A*
<175F
A*
A*
Liquid
A*
A*
Cellosolve
Acetate
Liquid
A*
A*
Cellulose
Acetate
Solid
A*
A*
Cellulose
Viscose
Solid
A*
A*
Liquid
A*
Cellulube
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
<70F
A*
<70F
A*
A*
A*
A*
<160F
A*
<25%,
<160F
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
Solid
A*
Chlorinated Solvents
Liquid
A*
Liquid
A* PTFE
Liquid
A* PTFE
Liquid
<70F
A* FKM
Liquid
<70F
A* FKM
Cement
Condition
Coating
Condition
A*
UHMWPE
Chlorine Dioxide
Gas
Solid
Chloroacetic Acid
<25%,
<160F
A*
Liquid
Chloroacetic Acid
Solid
Chloroacetic Acid
Solid
Chloroacetic Acid
Liquid
Chloroacetic Acid
Solid
Chloroacetone
<25%,
<160F
A* PTFE
A* PTFE
A* PTFE
A* PTFE
<25%,
<160F
A*
Liquid
A*
Chlorobenzene
Liquid
A*
<3%, <75F
A*
Chlorobenzene
Liquid
A*
<160F
A*
Chlorobenzene
Liquid
A*
A*
Chlorobromomethane
Liquid
A*
Chlorobromomethane
Liquid
A*
Chlorobutadiene
Liquid
A*
A*
Chlorobutadiene
Liquid
A*
A*
Chloroform
Liquid
A*
A*
Chlorosulfonic Acid
(Wet or Dry)
Liquid
A*
Chlorosulfonic Acid
(Wet or Dry)
Liquid
A*
A* PTFE
<140F
A* PTFE
<70F
A* PTFE
A* PTFE
<160F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Corrosive
Media
Physical
State
Chlorotoluene
Liquid
Chlorotoluene
Liquid
Chlorotoluene
Liquid
Chlorotoluene
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
<50%,
<200F
A*
A*
<50%,
<200F
A*
<100F
A*
A*
<50%,
<200F
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
Coating
A*
PTFE
<200F
A* FKM
<200F
A* FKM
Liquid
A*
PTFE
Chlorox
Liquid
A*
Chromic Acid
Liquid
A*
PTFE
Chromic Acid
Liquid
A*
PTFE
Chromium
Potassium
Sulfate
Solid
A*
Cider
Liquid
A*
Citric Acid
Solid
<100F
Citric Acid
Solid
<50%,
<200F
Citric Acid
Solid
Citric Acid
Solid
Condition
Condition
<200F
<200F
<140F
<50%,
<200F
UHMWPE
Citric Acid
Solid
A*
PTFE
Citric Acid
Solid
A*
PTFE
Citrus Juices
Liquid
A*
Cobalt Chloride
Solid
A*
PTFE
Cobalt Chloride
Solid
A*
PTFE
Coconut Oil
(See Oil,
Coconut)
Cod Liver Oil
(See Oil, Cod
Liver)
Coffee (Dry or
Wet)
Solid
A*
A*
Gas
A*
A*
Liquid
A*
A*
Copper Acetate
Solid
A*
A*
Copper
Arsenate
Solid
A*
A*
Copper Chloride
(Dry)
Solid
A*
A*
A*
Cola Syrup
<160F
Cooking Oil
(See Oil Cooking)
Copper Cyanide
Solid
N
<10%,
<212F
A*
<180F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Seat/Disc Materials
Condition
DI
NDI
AIBR
316
SS
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
Copper Nitrate
Solid
<5%, <75F
A*
Copper Nitrate
Solid
<5%, <75F
A*
Copper Nitrate
Solid
<50% Soln.
A*
Copper Nitrate
Solid
<50% Soln.
A*
A*
Copper Plating
Soln.
Liquid
A*
A*
Copper Sulfate
Solid
<10%,
<212F
A*
<25%,
<150F
A*
Copper Sulfate
Solid
<10%,
<212F
A*
<70F
A*
Copper Sulfate
Solid
<25%,
<150F
A*
<70F
A*
Copper Sulfate
Solid
<25%,
<150F
A*
<25%,
<150F
A*
A*
A*
A*
Liquid
A*
Cresote Oil
(See Oil Cresote)
Cresylic Acid
Liquid
A*
Cresylic Acid
Liquid
A*
A*
A*
A*
A*
A*
A*
A*
Solid
Liquid
Gas
<75F
A*
Cyclohexane
Liquid
A*
Cyclohexane
Liquid
A*
Cyclohexane
Liquid
<75F
A*
Cyclohexane
Liquid
<75F
A*
Cyclohexanol
Liquid
Cyclohexanone
Liquid
Liquid
Cyclohexanone
Cyclohexanone
<160F
Liquid
<100F
<180F
<180F
A*
100%,
<75F
A*
A*
100%,
<75F
A*
A*
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Seat/Disc Materials
Corrosive
Media
Physical
State
Cyclohexanone
Liquid
A*
DDT Intermediates
Liquid
A*
Decalin
Liquid
A*
Detergent
Solutions
Developing
Solutions
(Photography)
Liquid
Liquid
Diacetone Alcohol
Liquid
Diacetone Alcohol
Liquid
Dibenzyl Ether
Liquid
Dibenzyl Sebacate
Condition
DI
NDI
AIBR
316
SS
EPDM
NBR
Coating
Condition
PTFE
S20/21
PTFE
S22/23
A*
A*
FKM
UHMWPE
A*
A*
<75F
A*
A*
<100F
A*
A*
A*
A*
A*
A*
Liquid
A*
A*
Dibutyl Amine
Liquid
A*
A*
Dibutyl Ether
Liquid
A*
A*
Dibutyl Phthalate
Liquid
A*
A*
Dibutyl Sebacate
Liquid
A*
A*
Dichlorobenzene
(Ortho- and Para-)
Liquid
A*
PTFE
A*
Dichlorobenzene
(Ortho- and Para-)
Liquid
A*
PTFE
A*
Dichloroethane
(Dry)
Liquid
A*
A*
Dichlorohexylamine
Liquid
A*
A*
Dichlorophenol
Liquid
A*
A*
Diesel Fuel
Liquid
A*
A*
Diethanolamine
Liquid
A*
PTFE
A*
Diethanolamine
Liquid
A*
PTFE
A*
Diethanolamine
Liquid
<75F
A*
A*
Diethanolamine
Liquid
<212F
A*
<160F
A*
Diethanolamine
Liquid
<75F
A*
<160F
A*
Diethanolamine
Liquid
<212F
A*
A*
Diethyl Ether
Liquid
A*
A*
Diethyl Sebacate
Liquid
A*
A*
A*
A*
Diethylamine
Liquid
<160F
<160F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Corrosive
Media
Physical
State
Diethylene
Glycol
Liquid
Diisopropyl
Ketone
Liquid
Dimethyl Aniline
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
Liquid
A*
A*
Dimethyl
Formamide
Liquid
A*
Dimethyl
Formamide
Liquid
A*
A*
Dimethyl
Formamide
Liquid
<100F
A*
Dimethyl
Formamide
Liquid
<100F
A*
A*
Dinitrobenzene
Liquid
<70F
A* FKM
A*
Dinitrobenzene
Liquid
<70F
A* FKM
A*
Dinitrobenzene
Liquid
A*
Dinitrobenzene
Liquid
A*
Dinitrotoluene
Solid
A*
Dinitrotoluene
Solid
A*
Dioctyle
Phthalate
Liquid
A*
Dioctyle
Phthalate
Liquid
A*
Dioctyle
Phthalate
Liquid
<140F
A*
Dioctyle
Phthalate
Liquid
<140F
A*
Dioxanc
Liquid
A*
A*
Dioxolane
Liquid
A*
A*
Dipentene
Liquid
A*
A*
Dipentene
Liquid
A*
A*
Diphenyl
Solid
<212F
A*
A*
Diphenyl Oxide
Solid
<140F
A*
Diphenyl Oxide
Solid
A*
Diphenyl Oxide
Solid
A*
Diphenyl Oxide
Solid
A*
Disodium
Phosphate
Solid
A*
A*
A*
A*
Dowtherm
Drilling Mud
Condition
Liquid
Liquid
DI
NDI
AIBR
316
SS
A*
A*
<140F
<140F
A* PTFE
Condition
<70F
<70F
A* PTFE
A* PTFE
A* PTFE
<170F
A*
<140F
Coating
A* PTFE
A* PTFE
A
B
<160F
A* FKM
<140F
A* PTFE
A* PTFE
A* FKM
A*
UHMWPE
<140F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
A*
Disc Materials
Corrosive
Media
Physical
State
Drycleaning Fluids
Seat/Disc Materials
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
Liquid
A*
Dyes
Liquid
A*
Enamel
Liquid
Epichlorohydrin
Liquid
Epoxy Resins
Liquid
Ethane
Condition
Gas
Ethane
Ethanolamine
Liquid
Ethy Acetate
Liquid
Ethyl Acetoacetate
Liquid
Ethyl Alcohol
Liquid
Ethyl Alcohol
Liquid
EPDM
NBR
A*
A*
A*
A*
B
N
Coating
Condition
FKM
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
<180F
100%,
<170F
Ethyl Benzene
Liquid
A*
Ethyl Benzene
Liquid
A*
Ethyl Benzoate
Liquid
A*
Ethyl Butyrate
Liquid
A*
Ethyl Cellosolve
Liquid
A*
Ethyl Cellulose
Solid
A*
Gas
A*
Gas
Ethyl Ether
Liquid
Ethyl Formate
N
B
A*
A*
A*
A*
A*
Liquid
A*
A*
Ethyl Mercaptan
Liquid
A*
A*
Ethyl Oxalate
Liquid
A*
A*
Ethyl
Pentachlorobenzene
Liquid
A*
A*
Ethyl
Pentachlorobenzene
Liquid
A*
A*
Ethyl Silicate
Liquid
A*
A*
A*
<170F
Ethylene
Gas
A*
<70F
A*
A*
Ethylene
Gas
A*
<200F
A*
A*
A*
Ethylene
Gas
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Seat/Disc Materials
Corrosive
Media
Physical
State
Ethylene
Bromide
Liquid
A*
Ethylene
Bromide
Liquid
A*
Ethylene
Chloride
Liquid
A*
Ethylene
Chloride
Liquid
A*
Ethylene
Chlorohydrin
Liquid
A*
Ethylene
Chlorohydrin
Liquid
A*
Ethylene
Chlorohydrin
Liquid
Ethylene
Diamine
Liquid
Ethylene
Diamine
Liquid
Ethylene
Dichloride
Liquid
A*
PTFE
Ethylene
Dichloride
Liquid
A*
PTFE
Ethylene Glycol
Liquid
A*
Ethylene Glycol
Liquid
A*
Ethylene Oxide
Gas
Ethylene Oxide
Gas
<10F
Ethylene Oxide
Gas
<10F
Ethylene Oxide
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
<200F
A*
<180F
A*
A*
<70F
A*
<180F
A*
A*
A*
A*
A*
A*
<100F
A*
<140F
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
Gas
A*
<140F
A*
Ethylene
Trichloride
Liquid
A*
<180F
A*
Ethylene
Trichloride
Liquid
A*
Condition
<100F
DI
NDI
AIBR
316
SS
Coating
Condition
<140F
UHMWPE
A*
A*
Fatty Acids
Liquid
<180F
A*
<44%,
<180F
Fatty Acids
Liquid
<180F
A*
<44%,
<180F
A*
Fatty Acids
Liquid
<180F
A*
<44%,
<180F
A*
Fatty Acids
Liquid
A*
<44%,
<180F
A*
Fatty Acids
Liquid
A*
<44%,
<180F
A*
Fatty Acids
Liquid
A*
<44%,
<180F
A*
Fatty Acids
Liquid
A*
<44%,
<180F
A*
<44%,
<180F
A*
<180F
Fatty Acids
Liquid
A*
Ferric Chloride
Solid
A*
Ferric Chloride
Solid
<25%,
<150F
A*
PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AIBR
316
SS
Coating
A*
PTFE
Ferric Chloride
Solid
Ferric Chloride
Solid
<25%,
<150F
A*
Ferric Hydroxide
Liquid
<75F
A*
Ferric Nitrate
Solid
Ferric Nitrate
Solid
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
<25%,
<200F
A*
<25%,
<200F
A*
A*
Condition
<25%,
<212F
N
N
A*
A*
N
N
B
<25%,
<212F
A*
A*
A*
A*
Ferric Nitrate
Solid
Ferric Nitrate
Solid
Ferric Sulfate
Solid
<50%,
<160F
A*
Ferric Sulfate
Solid
A*
<50%,
<160F
A*
Ferric Sulfate
Solid
A*
A*
Ferric Sulfate
Solid
A*
Ferrous
Ammonium Sulfate
Solid
A*
Ferrous Chloride
Solid
A*
Ferrous Sulfate
Solid
A*
Ferrous Sulfate
Solid
A*
Ferrous Sulfate
Solid
<10%, <75F
A*
Ferrous Sulfate
Solid
<10%, <75F
A*
A*
A*
A*
A*
A*
Gas
A*
Gas
A*
Flue Gas
Gas
A*
PTFE
A*
Flue Gas
Gas
<160F
A* NBR
A*
Flue Gas
Gas
<160F
A* NBR
<160F
A*
Flue Gas
Gas
A*
PTFE
A*
PTFE
A*
PTFE
<160F
A*
<140F
A*
<140F
A*
A
A
<140F
Fluoboric Acid
Liquid
Fluoboric Acid
Liquid
Fluoboric Acid
Liquid
<30%, <75F
A*
<140F
A*
<30%, <75F
A*
<140F
A*
<140F
<140F
A*
Fluoboric Acid
Fluoboric Acid
Liquid
Liquid
A* EPDM
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Fluoboric Acid
Liquid
Fluorobenzene
Disc Materials
Seat/Disc Materials
316
SS
Coating
A*
EPDM
Liquid
A*
Fluorobenzene
Liquid
A*
Fluosilicic Acid
Liquid
A*
Fluosilicic Acid
Liquid
A*
Formaldehyde
Gas
<140%,<212F
A*
Formaldehyde
Gas
<140%,<212F
A*
Formaldehyde
Gas
<100%,<250
A*
Formaldehyde
Gas
<100%,<250
A*
Formamide
Solid
Formic Acid
Condition
DI
<140F
NDI
AIBR
Liquid
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
<140F
A*
<180F
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
Condition
<140F
<40F
<40F
A*
N
A*
PTFE
Formic Acid
Liquid
<90%,<212F
A*
PTFE
Formic Acid
Liquid
<90%,<212F
Formic Acid
Liquid
A*
PTFE
A*
PTFE
A*
A*
A*
A*
A*
<160F
A*
<160F
A*
<140F
<140F
Freon 11
Gas
Freon 11
Gas
Freon 11
Gas
Freon 11
Gas
A*
Freon 113
Gas
A*
A*
Freon 114
Gas
A*
A*
Freon 114Bs
Gas
A*
A*
Freon 115
Gas
A*
A*
Freon 12
Gas
A*
A*
Freon 13
Gas
A*
A*
Freon 13B1
Gas
A*
A*
Freon 21
Gas
A*
A*
Freon 22
Gas
A*
A*
Freon C318
Gas
A*
A*
A*
A*
Fruit Juices
Liquid
<160F
<140F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
UHMWPE
Corrosive
Media
Disc Materials
Physical
State
Condition
DI
NDI
AIBR
Seat/Disc Materials
316
SS
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
UHMWPE
Solid
A*
Fumaric Acid
Solid
A*
<70F
A*
Fumaric Acid
Solid
A*
<160F
A*
Furan
Liquid
A*
A*
A*
<120F
A*
<120F
A*
A*
Furan
Liquid
Furfural
Liquid
Gallic Acid
<140F
A*
<100F
A*
Solid
<75F
A*
Gallic Acid
Solid
<120F
Gallic Acid
Solid
<75F
A*
Gallic Acid
Solid
A*
PTFE
A* FKM
A*
PTFE
A*
A*
A*
A
N
<120F
A*
PTFE
A* FKM
Gas
A*
A*
Gas - Furnace
Gas
A*
A*
Gas Manufacturer
Gas
A*
A*
Gas - Natural
Gas
A*
A*
Gasoline - Ethyl
Liquid
A*
A*
Gasoline - Regular
Liquid
A*
A*
Gasoline - Regular
Liquid
A*
A*
Gasoline - Regular
Liquid
Gasoline - Regular
Liquid
A*
Liquid
A*
A*
Gelatine
Solid
A*
A*
Glucose
Liquid
A*
A*
Glue
Liquid
A*
A*
Glycerine
Liquid
<100F
A*
A*
Glycerine
Liquid
<100F
A*
A*
A*
Gallic Acid
Solid
Gallic Acid
Solid
Glycerine
Liquid
<120F
<85F
N
<85F
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Glycerine
Disc Materials
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AIBR
316
SS
Liquid
A*
Glycols
Liquid
A*
Grease
Liquid
A*
Green Sulfate
Liquors
Liquid
Condition
Coating
Condition
Gas
Heptane
Liquid
A*
Heptane
Liquid
A*
Hexane
Liquid
A*
Hexane
Liquid
<70F
A*
Liquid
100%,
<75F
A*
Hexane
Liquid
100%,
<75F
A*
A*
Hexyl Alcohol
Liquid
A*
A*
Hexylene Glycol
Liquid
A*
A*
Hydraulic Fluid
(Pydraul)
Hydraulic Oil Cellulube (See Oil
- Hydraulic,
Cellulube)
Hydraulic Oil Petroleum Base
(See Oil Hydraulic,
Petroleum Base)
Hydraulic Oil Water Base (See
Oil - Hydraulic,
Water Base)
Liquid
A*
A*
Hydrazine
Liquid
A*
<75F
A*
Hydrobromic Acid
Liquid
<40%,<160F
A*
Hydrobromic Acid
Liquid
A*
A*
A*
A*
<15%,<75F
A*
Hexane
<40%,
<160F
<40%,
<160F
Hydrobromic Acid
Liquid
Hydrobromic Acid
Liquid
Hydrocarbons
(Aromatic)
Liquid
A*
Hydrochloric Acid
Liquid
Hydrochloric Acid
Liquid
Hydrochloric Acid
Liquid
A*
EPDM
A*
EPDM
A*
PTFE
A*
PTFE
A*
PTFE
<40%,<160F
<5%
A*
<15%,<75F
A*
<5%
A*
<15%,<75F
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Hydrochloric Acid
Liquid
Hydrochloric Acid
Liquid
Disc Materials
Seat/Disc Materials
DI
NDI
AIBR
316
SS
<5%
A*
<5%
A*
Condition
Coating
Hydrochloric Acid
Liquid
<37%
Hydrochloric Acid
Liquid
<37%
A*
EPDM
A*
EPDM
Hydrochloric Acid
Liquid
<37%
A*
EPDM
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
<25%,<140F
A*
A*
<15%,<75F
A*
<37%,<75F
A*
<25%,<140F
A*
A*
A*
A*
UHMWPE
Liquid
A*
EPDM
A*
PTFE
Liquid
A*
PTFE
<25%,<140F
A*
<140F
A*
<140F
A*
A*
A*
A*
Hydrochloric Acid
Liquid
Hydrochloric Acid
Hydrochloric Acid
<37%
<37%,<75F
Hydrochloric Acid
Liquid
A*
PTFE
Hydrocyanic Acid
Liquid
A*
PTFE
Hydrocyanic Acid
Liquid
<75F
A*
Hydrocyanic Acid
Liquid
<75F
A*
Hydrocyanic Acid
Liquid
<140F
Hydrocyanic Acid
Liquid
A*
EPDM
A*
PTFE
Hydrocyanic Acid
Liquid
<140F
A*
EPDM
<140F
A*
Hydrofluoric Acid
Liquid
<30%,<200F
A* FKM
<30%,<200F
A*
Hydrofluoric Acid
Liquid
<30%,<200F
A* FKM
<50%,<160F
A*
Hydrofluoric Acid
Liquid
<30%,<200F
A* FKM
A*
Hydrofluoric Acid
Liquid
<30%,<200F
A* FKM
A*
Hydrofluoric Acid
Liquid
<15F
A*
A*
Hydrofluoric Acid
Liquid
<50%,<160F
A* FKM
<30%,<200F
A*
Hydrofluoric Acid
Liquid
<50%,<160F
A* FKM
<60%,<130F
A*
Hydrofluoric Acid
Liquid
<15F
A*
<60%,<130F
A*
Hydrofluoric Acid
Liquid
<50%,<160F
A* FKM
<50%,<160F
A*
Hydrofluoric Acid
Liquid
<50%,<160F
A* FKM
A*
Hydrofluoric Acid
Liquid
<15F
A*
<30%,<200F
A*
Hydrofluoric Acid
Liquid
<60%,<130F
A* FKM
<50%,<160F
A*
Hydrofluoric Acid
Liquid
<60%,<130F
A* FKM
<60%,<130F
A*
Hydrofluoric Acid
Liquid
<15F
A*
<50%,<160F
A*
<60%,<130F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Hydrofluoric Acid
Liquid
Hydrofluoric Acid
Liquid
Hydrofluoric Acid
Disc Materials
Seat/Disc Materials
Condition
DI
NDI
AIBR
316
SS
Coating
<60%,<130F
A* FKM
A*
PTFE
A*
PTFE
Liquid
Hydrofluoric Acid
Liquid
Hydrofluoric Acid
Liquid
A*
PTFE
A*
PTFE
Hydrofluoric Acid
Liquid
A* FKM
Hydrofluosilicic
Acid
Hydrofluosilicic
Acid
Liquid
Liquid
A*
PTFE
A*
PTFE
Hydrofluosilicic
Acid
Hydrofluosilicic
Acid
Hydrofluosilicic
Acid
Liquid
<60%,<130F
<100F
Liquid
Liquid
<100F
A*
EPDM
A*
PTFE
A*
EPDM
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
<30%,<200F
A*
<50%,<160F
A*
A*
<60%,<130F
A*
<30%,<200F
A*
<100F
A*
<20%,140F
A*
A*
A*
<100F
A*
<20%,140F
A*
A*
<20%,140F
A*
<100F
A*
Condition
UHMWPE
Hydrofluosilicic
Acid
Hydrofluosilicic
Acid
Hydrofluosilicic
Acid
Liquid
<100F
Liquid
<20%,<140F
Liquid
<20%,<140F
A*
EPDM
A*
EPDM
A*
EPDM
Hydrofluosilicic
Acid
Hydrogen
Chloride (Gas Dry)
Liquid
<20%,<140F
A*
EPDM
Gas
A*
A*
Hydrogen Gas
Gas
A*
A*
Hydrogen
Peroxide
Liquid
<85%,<160F
A*
Hydrogen
Peroxide
Liquid
<75F
A*
<90%,<73F
Hydrogen
Peroxide
Hydrogen
Peroxide
Hydrogen
Sulfide
Liquid
<75F
A*
<85%,<160F
Liquid
<90%,<73F
Gas
Hydrogen
Sulfide
Hydrogen
Sulfide
Hydrogen
Sulfide
Gas
A*
A*
A*
A*
Liquid
A*
Liquid
A*
PTFE
A*
PTFE
<20%,<250F
A*
A*
EPDM
<20%,<250F
A*
A*
EPDM
A*
Hypochlorites
(Calcium)
Hypochlorites
(Calcium)
Hypochlorites
(Calcium)
Hypochlorites
(Calcium)
<75F
Gas
Gas
Liquid
Liquid
<75F
<20%,<250F
<20%,<250F
N
N
B
B
N
N
A
A*
B
A
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Hypochlorites
(sodium)
Disc Materials
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A* PTFE
A*
A* FKM
A*
A* FKM
A*
A* PTFE
A*
A* PTFE
A*
Liquid
A*
A*
Iodine
Liquid
A*
A*
Iodoform
Solid
A*
A*
Isoamyl Alcohol
Liquid
A* PTFE
A*
Isoamyl Alcohol
Liquid
A* PTFE
A*
Isoamyl Alcohol
Liquid
<160F
A* FKM
A*
Isoamyl Alcohol
Liquid
<160F
A* FKM
<160F
A*
Isoamyl Alcohol
Liquid
A*
<160F
A*
Isoamyl Alcohol
Liquid
A*
A*
Isooctane
Liquid
A*
A*
Isophorone
Liquid
A*
A*
Isopropyl Chloride
Liquid
A*
A*
Isopropyl Acetate
Liquid
A*
A*
Isopropyl Alcohol
Liquid
A*
A*
Isopropyl Ether
Liquid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Kerosene
Liquid
A*
A*
Kerosene
Liquid
A*
A*
Kerosene
Liquid
A*
A*
Kerosene
Liquid
A*
A*
Ketchup
Liquid
A*
A*
Ketones-General
Liquid
A*
A*
DI
NDI
AI
BR
316
SS
Coating
Condition
Liquid
A* PTFE
<20%
Hypochlorites
(sodium)
Liquid
Hypochlorous Acid
Liquid
<70F
Hypochlorous Acid
Liquid
<70F
Hypochlorous Acid
Liquid
Hypochlorous Acid
Liquid
Ink
Condition
<75F
<75F
<70F
<70F
<120F
<160F
<80F
<250F
<250F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Ketones - General
Disc Materials
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
<140F
A*
A*
EPDM
<25%,<200F
A*
A*
EPDM
<140F
A*
<25%,<200F
A*
DI
NDI
AI
BR
316
SS
Liquid
A*
Lacquer Solvents
Liquid
Lacquers
Liquid
Lactic Acid
Liquid
<140F
Lactic Acid
Liquid
<25%,<200F
Condition
Coating
Condition
<180F
Lactic Acid
Liquid
<25%,<200F
Lactic Acid
Liquid
<140F
A*
Lactic Acid
Liquid
A*
PTFE
<140F
A*
<25%,<200F
A*
A*
A*
A*
Lactic Acid
Liquid
A*
PTFE
Lactic Acid
Liquid
A*
PTFE
Lactic Acid
Liquid
A*
Lactic Acid
Liquid
Lard
Latex
<140F
A*
EPDM
Liquid
A*
A*
Liquid
A*
A*
A*
A*
<25%,<200F
Solid
Lead Sulfamate
Solid
Lead Sulfamate
A*
EPDM
A*
Solid
A* FKM
A*
Lead Sulfamate
Solid
A* FKM
<140F
A*
Lead Sulfamate
Solid
<140F
<140F
A*
Lead Sulfate
Solid
<160F
A*
EPDM
A*
EPDM
<160F
A*
Lead Sulfate
Solid
A* FKM
<160F
A*
Lead Sulfate
Solid
A*
EPDM
A*
Lead Sulfate
Solid
A* FKM
A*
Lime
Solid
A*
A*
Lime-Sulfur
Solid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
<140F
<160F
<140F
<140F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Liquid
Liquid
Liquid Soap
Disc Materials
Condition
<140F
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AI
BR
316
SS
A*
A*
Coating
Condition
<140F
UHMWPE
Liquid
A*
Liquified Petroleum
Gas
Lubricating Oils Petroleum (See
Oils - Lubricating
Petrolium)
Lye (See Sodium
Hydroxide)
Gas
A*
Magnesium
Ammonium Sulfate
Magnesium
Ammonium Sulfate
Magnesium
Bisulfate
Solid
Solid
Solid
A*
Magnesium
Carbonate
Magnesium
Carbonate
Magnesium
Carbonate
Solid
A*
Solid
A*
Solid
A*
A*
Magnesium
Carbonate
Magnesium
Chloride
Magnesium
Hydroxide
Solid
A*
A*
Solid
A*
A*
Solid
A*
A*
Magnesium Nitrate
Solid
A*
A*
Magnesium Oxide
Solid
A*
A*
Magnesium Sulfate
Solid
<25%,<150F
A*
A*
Maleic Acid
Solid
<70F
A*
A*
Maleic Acid
Solid
<140F
A*
A*
Maleic Acid
Solid
<140F
A*
A*
Maleic Acid
Solid
A*
PTFE
A*
Maleic Acid
Solid
A*
PTFE
A*
Maleic Acid
Solid
A*
<140F
A*
Maleic Anhydride
Solid
A*
<140F
A*
Maleic Anhydride
Solid
A*
A*
Malic Acid
Solid
A*
A*
<50%
<50%
<70F
A*
PTFE
A*
PTFE
<140F
<180F
A
<180F
<140F
<140F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
DI
NDI
AI
BR
316
SS
Seat/Disc Materials
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
UHMWPE
Malic Acid
Solid
<140F
A*
Malic Acid
Solid
<140F
A*
Malic Acid
Solid
A*
Manganese
Chloride
Solid
A*
A*
Manganese
Sulfate
Solid
A*
A*
Mash - Breweries
Solid
A*
UHMWPE
A*
Mercuric
Chloride
Mercuric
Chloride
Liquid
<10%,<140F
A* EPDM
A*
Liquid
<10%,<140F
A* EPDM
A*
Mercuric
Chloride
Liquid
A* PTFE
A*
Mercuric
Chloride
Liquid
A* PTFE
A*
Mercuric Cyanide
Solid
<140F
A* NBR
A*
Mercuric Cyanide
Solid
<140F
A* NBR
A*
Mercuric Cyanide
Solid
A* PTFE
A*
Mercuric Cyanide
Solid
A* PTFE
A*
Mercuric Nitrate
Solid
A* PTFE
A*
Mercurous
Nitrate
Solid
A*
A*
Mercury
Liquid
<140F
A*
Mercury
Liquid
<140F
A*
Mercury
Liquid
Mercury
Liquid
Mesityl Oxide
Liquid
A*
Methacrylic
Esters
Liquid
Gas
A*
B
Methane
<140F
<140F
<10%,<140F
<10%,<140F
<140F
<140F
B
B
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
<20%,<70F
A*
<140F
<140F
Methyle Acetate
Liquid
Methyle Acetate
Liquid
Methyle Acetate
Liquid
<20%,<70F
A*
<20%,<70F
A*
Methyle Acetate
Liquid
<20%,<70F
A*
<140F
A*
Methyle Acetate
Liquid
A* PTFE
<140F
A*
Methyle Acetate
Liquid
A* PTFE
A*
<20%,<70F
A* PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Methyl Acetone
Disc Materials
Seat/Disc Materials
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AI
BR
316
SS
Liquid
A*
Methyl Acrylate
Liquid
A*
Methyl Acrylate
Liquid
A*
Methyl Alcohol
Liquid
A*
Methyl Alcohol
Liquid
<75F
A*
Methyl Alcohol
Liquid
<75F
A*
Methyl Alcohol
Liquid
A*
Methyl Amine
Liquid
A*
Gas
A*
A*
Methyl Bromide
Condition
Coating
Condition
<160F
EPDM
UHMWPE
Methyl Butyl
Ketone
Liquid
Methyl Cellosolve
Liquid
A*
Methyl Cellulose
Solid
A*
Methyl Cellulose
Solid
A*
Methyl Cellulose
Solid
<100F
A*
Methyl Cellulose
Solid
<100F
A*
A*
Methyl Chloride
Gas
A*
A*
Methyl Ethyl
Ketone
Liquid
A*
A*
Methyl Ethyl
Ketone
Liquid
<140F
A*
A*
Methyl Ethyl
Ketone
Liquid
<140F
A*
A*
Methyl Ethyl
Ketone
Liquid
A*
A*
Methyl Formate
Liquid
A*
A*
Methyl Isobutyl
Ketone
Liquid
A*
Methyl Isobutyl
Ketone
Methyl Isobutyl
Ketone
Methyl Isobutyl
Ketone
Liquid
A*
A*
Methyl
Methacrylate
<140F
<140F
<140F
<140F
Liquid
<100F
A*
Liquid
<100F
A*
A*
Liquid
A*
A*
Methyl Oleate
Liquid
A*
A*
Methyl Propyl
Ketone
Liquid
A*
A*
Methylene Bromide
Liquid
A*
A* PTFE
<180F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Methylene Bromide
Disc Materials
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AI
BR
316
SS
Coating
Liquid
A*
PTFE
Methylene Chloride
Liquid
A*
Methylene Chloride
Liquid
Milk
Liquid
A*
Mineral Spirits
Liquid
Molasses
Liquid
Condition
Condition
<22%,<140F
Monochloroacetic
Acid
Monochloroacetic
Acid
Solid
Solid
Monochlorobenzene
(Dry)
Liquid
A*
Monochlorobenzene
(Dry)
Liquid
A*
A*
Monomethylaniline
Liquid
A*
A*
A*
37%,<130F
A*
37%,<130F
A*
A*
A*
A*
PTFE
A*
PTFE
<160F
<180F
UHMWPE
Liquid
Muriatic Acid
Liquid
Muriatic Acid
Liquid
Muriatic Acid
Liquid
Mustard
Liquid
Naphtha
Liquid
A*
<140F
A*
Naphthalene
Solid
A*
<170F
A*
Naphthalene
Solid
A*
A*
Naphthemic Acid
Liquid
A*
A*
A*
A*
A*
A*
<10%,<100F
A*
<160F
A*
<160F
A*
A*
Natural Gas
37%,<130F
37%,<130F
A*
A*
A*
Gas
Nickel Acetate
Solid
Nickel Acetate
Nickel Acetate
A*
Solid
Solid
Nickel Acetate
Solid
Nickel Ammonium
Sulfate
Solid
Nickel Ammonium
Sulfate
Solid
Nickel Ammonium
Sulfate
Solid
<160F
A*
<160F
A*
<10%,<100F
A*
PTFE
<10%,<100F
A*
PTFE
A*
EPDM
A*
PTFE
A*
PTFE
A*
EPDM
A*
PTFE
<10%,<100F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Coating
A*
PTFE
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
UHMWPE
Nickel Ammonium
Sulfate
Solid
Nickel Chloride
Solid
A*
Nickel Nitrate
Solid
A*
Nickel Sulfate
Solid
A*
Nicotine Sulfate
Solid
Nicotinic Acid
Liquid
A*
Nicotinic Acid
Liquid
A*
Nitrana Solutions
Liquid
A*
A*
Nitric Acid
Liquid
A*
A*
A*
<5%
A*
<25%,<150F
<95%,<75F
<180F
A*
PTFE
<160F
30%,<140F
Nitric Acid
Liquid
A*
PTFE
Nitric Acid
Liquid
A*
PTFE
Nitric Acid
Liquid
<5%
A*
30%,<140F
A*
Nitric Acid
Liquid
<5%
A*
<5%
A*
Nitric Acid
Liquid
<5%
A*
A*
A*
A*
A*
A*
Nitric Acid
Liquid
Nitric Acid
Liquid
Nitric Acid
A*
PTFE
<95%,<75F
A*
Liquid
<95%,<75F
A*
Nitric Acid
Liquid
<80%,<100F
A*
Nitric Acid
Liquid
<80%,<100F
30%,<140F
A*
Nitric Acid
Liquid
<80%,<100F
A*
<5%
A*
Nitric Acid
Liquid
<40%,<200F
A*
A*
Nitric Acid
Liquid
<40%,<200F
A*
30%,<140F
A*
Nitric Acid
Liquid
<40%,<200F
A*
<5%
A*
Nitrobenzene
Solid
A*
A*
Nitrobenzene
Solid
A*
A*
Nitroethane
Liquid
A*
A*
Nitrogen - Gas
Gas
A*
A*
Nitromethane
Liquid
A*
A*
Nitrous Acid
Liquid
A*
A*
10%,<70F
30%,<140F
<5%
<180F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Nitrous Acid
Disc Materials
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Oil - Coconut
Liquid
A*
A*
Liquid
A*
Oil - Cooking
Liquid
A*
A*
Oil - Corn
Liquid
A*
A*
Oil - Cottonseed
Liquid
A*
A*
Oil - Creosote
Liquid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Oil - Fish
Liquid
A*
A*
Oil - Fuel
Liquid
A*
A*
Oil - Fuel
Liquid
<140F
A*
<200F
A*
Oil - Fuel
Liquid
<140F
A*
<200F
A*
Oil - Fuel
Liquid
A*
A*
Oil - Halowax
Liquid
A*
A*
Oil - Hydraulic
(Cellulube)
Oil - Hydrolic
(Petrol. Base)
Liquid
A*
A*
A*
Liquid
A*
A*
Oil - Hydraulic
(Water Base)
Liquid
A*
A*
Oil - Lavender
Liquid
Oil - Linseed
Liquid
Oil - Lubricating
(Petroleum)
Liquid
DI
NDI
AI
BR
316
SS
Coating
Condition
Liquid
A* PTFE
<70F
Nitrous Acid
Liquid
A* PTFE
Nitrous Acid
Liquid
A*
Octane
Liquid
A*
Octyle Alcohol
Liquid
Oil - Aniline
Liquid
Oil - Animal
Liquid
A*
Oil - Castor
Condition
10%,<70F
A*
A*
B
A*
<70F
UHMWPE
A*
A*
A*
A*
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Seat/Disc Materials
Corrosive
Media
Physical
State
Oil - Lubricating
(Petroleum)
Liquid
Oil - Lubricating
(Petroleum)
Liquid
Oil - Lubricating
(Petroleum)
Liquid
Oil - Mineral
Liquid
Oil - Motor
Liquid
A*
Oil - Motor
Liquid
Oil - Motor
Liquid
<140F
A*
Oil - Motor
Liquid
<140F
A*
Oil - Olive
Liquid
Oil - Palm
Condition
<140F
DI
NDI
AI
BR
316
SS
A*
A
A*
Coating
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
<140F
A*
<140F
A*
A
B
Condition
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
Liquid
A*
A*
Oil - Peanut
Liquid
A*
A*
Oil - Pine
Liquid
A*
A*
Oil - Pyridine
Liquid
A*
A*
Oil - Rosin
Liquid
A*
A*
Oil - Silicone
Liquid
A*
A*
Oil - Soybean
Liquid
A*
A*
Oil - Tall
Liquid
A*
A*
Oil - Transformer
Liquid
A*
A*
Oil - Transformer
Liquid
A*
A*
Oil - Turbine
Liquid
A*
A*
Oil - Vegetable
Liquid
A*
A*
Oleic Acid
Liquid
A*
A*
Oleic Acid
Liquid
A*
A*
Oleic Acid
Liquid
<140F
A*
A*
Oleic Acid
Liquid
<140F
A*
A*
Oleum
Liquid
A*
A*
Oxalic Acid
Solid
<10%,<75F
A*
A*
Oxalic Acid
Solid
<10%,<75F
A*
A*
Oxalic Acid
Solid
A*
<140F
<140F
<140F
<140F
<140F
<160F
A* PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
316
SS
Coating
A*
PTFE
DI
NDI
AI
BR
Seat/Disc Materials
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
Oxalic Acid
Solid
Oxalic Acid
Solid
<160F
A*
Oxalic Acid
Solid
<160F
A*
Oxygen - Gas
Gas
A*
Gas
A*
Gas
A*
Liquid
A*
Paint Thinner/Remover
Liquid
A*
Liquid
A*
Liquid
A*
Solid
A*
Solid
A*
PTFE
Solid
A*
PTFE
Solid
Paraffin
Solid
A*
Paraformaldehyde
Solid
<160F
<160F
<160F
<160F
A
<140F
<100F
A*
<160F
A*
A*
A*
A*
A*
A*
A*
A*
<160F
Solid
A*
Pentachlorophenol
Liquid
A*
A*
A*
A*
Pentane
Gas
Perchlorethylene
Liquid
<100F
A*
A*
Perchlorethylene
Liquid
<100F
A*
A*
Perchlorethylene
Liquid
A*
<200F
A*
Perchlorethylene
Liquid
A*
<200F
A*
100%,<75F
A*
A*
Perchloric Acid
Liquid
N
N
N
N
N
N
A*
PTFE
A*
PTFE
Perchloric Acid
Liquid
Phenolates (DiNitrols)
Liquid
A*
A*
Phenols (Di-Nitrols
Liquid
A*
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Disc Materials
Seat/Disc Materials
Corrosive
Media
Physical
State
Liquid
A*
Phenylhydrazine
Liquid
A*
Condition
DI
NDI
AI
BR
316
SS
Coating
Phorone
Liquid
Phorone
Liquid
A*
PTFE
A*
PTFE
A*
PTFE
A*
PTFE
Phosphate Esters
Liquid
Phosphate Esters
Liquid
Phosphate Esters
Liquid
Phosphate Esters
Liquid
A*
EPDM
A*
EPDM
Condition
<100F
<200F
<200F
Phosphoric Acid
Liquid
A*
PTFE
Phosphoric Acid
Liquid
A*
PTFE
Phosphoric Acid
Liquid
A*PTFE
Phosphoric Acid
Liquid
<85%,<180F
A*
Phosphoric Acid
Liquid
<85%,<180F
A*
<85%,<180F
Phosphoric Acid
Liquid
<85%,<180F
A*
<120F
Phosphorous
Oxychloride
Liquid
Phosphorous
Trichloride Acid
Phosphorous
Trichloride Acid
Liquid
Liquid
<120F
A*
B
B
A*
PTFE
A*
PTFE
Phthalic Acid
Liquid
A*
PTFE
Phthalic Acid
Liquid
A*
PTFE
Phthalic Anhydride
Liquid
A*
Phthalic Anhydride
Liquid
A*
<140F
<100F
<100F
Pickling Solutions
(20%HN0_3,4%HF)
Liquid
A*
PTFE
Liquid
A*
PTFE
<85%,<180F
<140F
Liquid
<140F
A*
<70F
Liquid
<140F
A*
<140F
Liquid
<140F
A*
Liquid
Liquid
Liquid
<140F
A*
A*
PTFE
<70F
<10%,<140F
A*PTFE
<10%,<140F
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
UHMWPE
Corrosive
Media
Physical
State
Liquid
Liquid
Pineapple Juice
Liquid
Pinene
Disc Materials
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Coating
A* PTFE
A*
Liquid
A*
Pinene
Liquid
A*
Piperidine
Liquid
A* PTFE
Piperidine
Liquid
A* PTFE
Liquid
A* PTFE
Liquid
A* PTFE
Plating Solutions
(Brass, Bronze,
Cadium, Copper,
Gold, Lead, Silver,
Tin, Zinc, Others)
Plating Solutions
(Brass, Bronze,
Cadium, Copper,
Gold, Lead, Silver,
Tin, Zinc, Others)
Plating Solutions
(Brass, Bronze,
Cadium, Copper,
Gold, Lead, Silver,
Tin, Zinc, Others)
Plating Solutions
(Brass, Bronze,
Cadium, Copper,
Gold, Lead, Silver,
Tin, Zinc, Others)
Plating Solutions
(Chrome and
Nickel)
Plating Solutions
(Chrome and
Nickel)
Plating Solutions
(Chrome and
Nickel)
Plating Solutions
(Chrome and
Nickel)
Poly Vinyl Acetate
Emulsions
Condition
Condition
<160F
<160F
<140F
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
Liquid
<140F
A*
EPDM
Liquid
<140F
A*
EPDM
Liquid
<140F
A*
EPDM
Liquid
<140F
A*
EPDM
Liquid
A* PTFE
Liquid
A* PTFE
Liquid
A*
A*
Polyester Resins
Liquid
A*
Potash, Caustic
(See Potassium
Hydroxide)
Potassium
Carbonate
Solid
A*
Potassium Cyanide
Solid
A*
EPDM
Potassium Cyanide
Solid
A* PTFE
Potassium Cyanide
Solid
A* PTFE
Potassium Cyanide
Solid
A*
EPDM
Potassium Iodide
Solid
A* FKM
Potassium Acetate
Solid
A*
<140F
<140F
100%,<75F
<140F
<140F
<140F
<140F
<140F
UHMWPE
A*
A*
A*
A*
A*
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
DI
NDI
AI
BR
Seat/Disc Materials
316
SS
Coating
Condition
PTFE
S20/21
PTFE
S22/23
EPDM
NBR
A*
FKM
UHMWPE
Potassium
Acetate
Solid
A*
Potassium
Acetate
Solid
A*
<180F
A*
Potassium
Acetate
Potassium
Bicarbonate
Solid
A*
<180F
A*
A*
Potassium
Bisulfite
Solid
A*
Potassium Borate
Solid
A*
Potassium
Bromide
Solid
A*
Potassium
Chlorate
Solid
Potassium
Chlorate
Solid
Potassium
Chlorate
Solid
Potassium
Chlorate
Solid
Solid
Potassium
Chlorate
Potassium
Chromate
Solid
Solid
Potassium
Chromate
Solid
Potassium
Dichromate
Potassium
Dichromate
Solid
A*
<25%,<150F
<100F
<100F
<50%,<212F
Solid
Potassium
Dichromate
Solid
Potassium
Dichromate
Solid
Potassium
Dichromate
Solid
Potassium
Dichromate
Solid
A*
A*
A*
A*
A*
A*
A*
A*
A*
<25%,<150F
<25%,<150F
Solid
Potassium
Dichromate
Potassium
Dichromate
Potassium
Dichromate
Potassium
Hydroxide
(Caustic Potash)
Potassium
Hydroxide
(Caustic Potash)
Potassium
Hydroxide
(Caustic Potash)
Potassium
Hydroxide
(Caustic Potash)
Potassium
Hypochloride
100%,<75F
A* FKM
<150F
A*
A*
<40%,<140F
A*
A*
A*
<150F
A*
A*
A*
PTFE
<150F
A*
A*
PTFE
<25%,<150F
A*
A*
A*
A*
A*
<150F
A*
<150F
A*
<50%,<212F
A*
Solid
<50%,<212F
A*
<25%,<150F
A*
Solid
<150F
A*
<25%,<150F
A*
Liquid
<100F
A*
A*
Liquid
<50%,<100F
A*
<180F
A*
Liquid
<100F
A*
<180F
A*
Liquid
<50%,<100F
A*
A*
A*
Liquid
<150F
A*
PTFE
A*
PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
DI
NDI
AI
BR
316
SS
Seat/Disc Materials
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A
A
Potassium Nitrate
Solid
<75F
A*
Potassium Nitrate
Solid
<75F
A*
Potassium Nitrate
Solid
Potassium Nitrate
Solid
Potassium
Permanganate
Solid
<5%,<175F
A*
Potassium
Permanganate
Solid
<5%,<175F
A*
Potassium
Permanganate
Solid
Potassium
Permanganate
Solid
Potassium
Phosphate
Solid
Potassium
Phosphate
Solid
Potassium
Phosphate
Solid
<150F
A*
Potassium
Phosphate
Solid
<150F
A*
A*
Potassium Silicate
Solid
A*
A*
Potassium Sulfate
Solid
A*
A*
Potassium Sulfide
Solid
A*
Potassium Sulfite
Solid
A*
A*
Potassium
Thiosulfate
Solid
A*
A*
Potassium
Triphosphate
Solid
A*
A*
Prestone
Antifreeze
Liquid
A*
A*
Producer Gas
Gas
A*
A*
Propane
Gas
A*
Propane
Gas
A*
A*
Propane
Gas
A*
A*
Propane
Gas
A*
Propionaldehyde
Liquid
A*
A*
Propionic Acid
Solid
A*
A*
Propionic Acid
Solid
A*
A*
A*
A*
<75F
<75F
<20%,<140F
<20%,<140F
Propionitrile
Solid
Propyl Alcohol
Liquid
A*
<160F
A*
PTFE
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
DI
NDI
AI
BR
316
SS
Seat/Disc Materials
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
Propylene
Gas
A*
Propylene
Gas
A*
Propylene
Dichloride
Solid
A*
A*
Propylene Glycol
Liquid
A*
Pulp Stock
Liquid
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
<150F
A*
<170F
A*
UHMWPE
Pydraul (See
Hydraulic Fluid Pydraul)
Pyranol
Liquid
A*
Liquid
Pyrogallic Acid
Liquid
Pyrogallic Acid
Liquid
Pyrogallic Acid
Liquid
Pyrrole
Liquid
Resins
Liquid
<140F
A*
<140F
A*
B
B
A*
A* PTFE
<140F
A* PTFE
<140F
Liquid
A*
Salicylic Acid
Solid
<180F
A*
Salicylic Acid
Solid
<180F
A*
A*
Salicylic Acid
Solid
A*
A*
Salicylic Acid
Solid
A*
<180F
A*
Salicylic Acid
Solid
A*
<70F
A*
Salicylic Acid
Solid
<180F
A*
<70F
A*
Sewage
Liquid
<150F
A*
A*
Sewage
Liquid
A*
A*
Shellac
Liquid
A*
A*
<180F
Silicone Grease
(See Oil - Silicone)
Silicone Grease
(See Oil - Silicone)
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
DI
NDI
AI
BR
316
SS
Seat/Disc Materials
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A
A
UHMWPE
Silver Cyanide
Solid
<75F
A*
<120F
A*
Silver Nitrate
Solid
<60%,<75F
A*
<75%,<160F
A*
Silver Nitrate
Solid
<60%,<75F
A*
Silver Nitrate
Solid
A*
Silver Nitrate
Solid
A*
Skellysolve
Liquid
A*
A*
Soap Solutions
(Detergent Soln.)
Soda Ash (See
Sodium
Carbonate)
Liquid
A*
A*
Sodium Acetate
Solid
A*
A*
Sodium Aluminate
Solid
A*
A*
Sodium Arsenate
Solid
A*
Solid
A*
A*
A*
A*
A*
A*
A
A*
Sodium
Bicarbonate
(Baking Soda)
Sodium
Bichromate
Solution
Sodium Bisulfate
(Black Sulfate
Liquor)
Sodium Bisulfate
(Black Sulfate
Liquor)
Sodium Bisulfate
(Black Sulfate
Liquor)
Sodium Borate
(Borax)
Liquid
<75%,<160F
A* PTFE
A*
Solid
A*
Solid
A*
<10%,<160F
Solid
A*
<40%
Solid
A*
UHMWPE
A*
Sodium Bromide
Solid
<70F
A* FKM
Sodium Bromide
Solid
<70F
A* FKM
<70F
A*
Sodium Bromide
Solid
<70F
A* FKM
<160F
A*
Sodium Bromide
Solid
A* PTFE
A*
Sodium Bromide
Solid
A* PTFE
<160F
A*
Sodium Bromide
Solid
A* PTFE
<70F
A*
Sodium
Carbonate
Solid
A*
A*
Sodium Chlorate
Solid
A*
A*
Sodium Chloride
Solid
A*
A*
Sodium Chloride
Solid
A*
A*
<130F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Coating
Sodium Chromate
Solid
A*
PTFE
Sodium Chromate
Solid
A*
PTFE
A*
EPDM
A*
EPDM
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
<140F
A*
<140F
A*
A*
Condition
UHMWPE
Sodium Chromate
Solid
<140F
Sodium Chromate
Solid
<140F
Sodium Cyanide
Solid
A*
A*
Sodium
Dichromate
Solid
A*
A*
Sodium Fluoride
Solid
A*
A*
Sodium
Hydrosulfide
Solid
<50%,<75F
Sodium
Hydrosulfite
Solid
<10%,<160F
A* NBR
Sodium
Hydrosulfite
Solid
A*
PTFE
Sodium
Hydrosulfite
Solid
A*
PTFE
A* NBR
Sodium
Hydrosulfite
Sodium Hydroxide
(Lye, Caustic
Soda)
Sodium Hydroxide
(Lye, Caustic
Soda)
Sodium Hydroxide
(Lye, Caustic
Soda)
Sodium Hydroxide
(Lye, Caustic
Soda)
Sodium
Hypochloride
A*
<10%,<160F
<10%<160F
<10%,<160F
A
B
A*
A*
A*
A*
A*
Solid
<10%,<160F
Liquid
<50%,<100F
A*
<73%,<190F
A*
Liquid
A*
<73%,<190F
A*
Liquid
A*
<50%
A*
A*
<50%
A*
A*
PTFE
A*
A*
PTFE
<140F
A*
Liquid
<50%,<100F
Solid
Sodium
Hypochloride
Solid
Sodium
Hypochlorite
Solid
Sodium
Hypochlorite
Solid
Sodium
Hypochlorite
<3%
A*
<10%,<160F
A*
<3%
A*
<3%
A*
Solid
A*
PTFE
A*
Sodium
Hypochlorite
Sodium
Hypochlorite
Sodium
Hypochlorite
Sodium
Hypochlorite
Sodium
Hypochlorite
Sodium
Hypochlorite
Solid
A*
PTFE
A*
A*
Sodium Iodide
Solid
<10%,<160F
Solid
<3%
A*
Solid
<10%,<160F
A* FKM
<3%
A*
Solid
<10%,<160F
A* FKM
<10%,<160F
A*
Solid
<10%,<160F
A* FKM
A*
A*
A*
PTFE
A*
EPDM
A*
Solid
<160F
<3%
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Coating
Sodium Iodide
Solid
A*
PTFE
Sodium Iodide
Solid
A*
PTFE
A*
EPDM
Sodium Iodide
Solid
Sodium
Metaphosphate
Liquid
Sodium
Metasilicate
Liquid
Sodium Nitrate
Solid
A*
Sodium Nitrite
Solid
Sodium Perborate
Solid
Sodium Perborate
Solid
Sodium Perborate
Solid
Sodium Perborate
Condition
<160F
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A* FKM
A*
A* FKM
A*
<10%,<212F
A*
EPDM
A*
Solid
<10%,<212F
A*
EPDM
A*
Sodium Perborate
Solid
<10%,<75F
A*
A*
Sodium Perborate
Solid
<10%,<75F
A*
<10%,<212F
A*
Sodium Peroxide
Solid
<10%,<120F
A*
Sodium Peroxide
Solid
<212F
A*
A*
Sodium Peroxide
Solid
<212F
A*
A*
Sodium Peroxide
Solid
A*
Sodium
Phosphate Monobasic,
Dibasic
Sodium
Phosphate Tribasic
Sodium Silicate
(Water Glass)
Sodium Silicate
(Water Glass)
<160F
<160F
<10%,<212F
<10%,<212F
<10%,<120F
Solid
A*
A*
Solid
A*
A*
A*
A*
A*
<75F
A*
<75F
A*
Liquid
<75F
Liquid
A*
EPDM
Sodium Silicate
(Water Glass)
Sodium Silicate
(Water Glass)
Liquid
A*
EPDM
A*
Sodium Sulfate
Solid
A*
A*
Sodium Sulfide
Solid
A*
A*
Sodium Sulfide
Solid
A*
Sodium Sulfite
Solid
A*
A*
Sodium
Tetraborate
Sodium
Thiosulfate
Solid
A*
A*
Solid
A*
A*
Liquid
<75F
<75F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Solvasol #1,#2,#3
Liquid
Solvasol #1,#2,#3
Liquid
Disc Materials
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Coating
<100F
A* NBR
<100F
A* NBR
A*
PTFE
A*
PTFE
Condition
Solvasol #1,#2,#3
Liquid
Solvasol #1,#2,#3
Liquid
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
A*
A*
<100F
A*
<10%,<130F
A*
A*
A*
Condition
<100F
UHMWPE
Liquid
Sannic Chloride
Liquid
A*
Sannic Chloride
Liquid
A*
Sannic Chloride
Liquid
A*
Stannous Chloride
Solid
A*
Stannous Chloride
Solid
<10%,<140F
A*
Stannous Chloride
Solid
<10%,<140F
A*
Stannous Chloride
Solid
A*
A*
Starch
Liquid
A*
A*
Liquid
A*
<250F
A*
Stearic Acid
Solid
A*
<140F
A*
Stearic Acid
Solid
A*
<140F
A*
A*
A*
A*
A*
<250F
<140F
A*
<10%,<130F
Liquid
A*
Stoddards Solvent
Liquid
A*
Styrene
Liquid
A*
Styrene
Liquid
A*
A*
Styrene
Liquid
<70F
A*
A*
Styrene
Liquid
<70F
A*
A*
Sugar Solutions
Liquid
A*
A*
Sulfite Liquors
Liquid
A*
A*
<125F
<70F
<70F
<5%,<180F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Disc Materials
Physical
State
Condition
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Sulfur
Solid
A*
Sulfur (Molten)
Liquid
A*
Sulfur Chloride
Liquid
Sulfur Chloride
Liquid
Sulfur Chloride
Liquid
Coating
Condition
EPDM
NBR
A*
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
FKM
A*
PTFE
<140F
A* FKM
<140F
A* FKM
A*
A*
PTFE
A*
<140F
A*
<140F
A*
Sulfur Chloride
Liquid
Solfur Dioxide
(Dry)
Gas
A*
A*
Sulfur Dioxide
(Wet)
Gas
A*
A*
Sulfur Trioxide
(Dry)
Solid
A*
A*
Sulfur Trioxide
(Dry)
Solid
A*
A*
Liquid
A*
PTFE
A*
A*
PTFE
<20%,<70F
A*
Sulfuric Acid
Liquid
Sulfuric Acid
Liquid
Sulfuric Acid
<120F
<20%,<70F
A*
<20%,<70F
A*
Liquid
<20%,<70F
A*
<30%,<220F
A*
Sulfuric Acid
Liquid
<20%,<70F
A*
A*
Sulfuric Acid
Liquid
<30%,<220F
A* FKM
<20%,<70F
A*
Sulfuric Acid
Liquid
<30%,<220F
A* FKM
<30%,<220F
A*
Sulfuric Acid
Liquid
<30%,<220F
A* FKM
A*
Sulfuric Acid
Liquid
A*
PTFE
A*
Sulfuric Acid
Liquid
A*
PTFE
A*
Sulfuric Acid
(Fuming)
Liquid
A*
PTFE
A*
Sulfurous Acid
Liquid
<70F
A*
A*
Sulfurous Acid
Liquid
<70F
A*
A*
Solid
<140F
A*
A*
A*
A*
A*
<140F
A*
A*
<140F
A*
Tannic Acid
(Tannin)
Tannic Acid
(Tannin)
Tannic Acid
(Tannin)
Solid
Solid
Solid
<140F
<30%,<220F
<70F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Tanning Solutions
Tar
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Tartaric Acid (Also
Dihydroxysuccinic
Acid)
Disc Materials
Condition
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
PTFE
A*
A*
PTFE
<10%,<212F
A*
A*
PTFE
<50%,<160F
A*
A*
DI
NDI
Liquid
Solid
Solid
Solid
Solid
AI
BR
316
SS
Coating
Condition
Solid
<50%,<160F
A*
Solid
<50%,<160F
A*
<50%,<160F
A*
Solid
<50%,<160F
A*
<10%,<212F
A*
Solid
<15%
A*
A*
Solid
<15%
A*
<50%,<160F
A*
Solid
<15%
A*
<10%,<212F
A*
A*
A*
Terpineol
Liquid
A*
Tertiary Butyl
Mercaptan
Liquid
A*
PTFE
Tertiary Butyl
Mercaptan
Liquid
A*
PTFE
<140F
A*
Tertiary Butyl
Mercaptan
Liquid
<140F
A* FKM
<140F
A*
Tertiary Butyl
Mercaptan
Liquid
<140F
A* FKM
A*
Tertiary Butyl
Alcohol
Solid
A*
A*
A*
Tertiary Butyl
Catechol
Liquid
A*
PTFE
Tertiary Butyl
Catechol
Liquid
A*
PTFE
<140F
A*
Tertiary Butyl
Catechol
Liquid
<140F
A* FKM
<140F
A*
Tertiary Butyl
Catechol
Liquid
<140F
A* FKM
A*
Terachloroethane
Liquid
A*
A*
Tetraethyl Lead
Liquid
A*
A*
TetraHydrofuran
Liquid
A*
A*
TetraHydrofuran
Liquid
A*
TetraHydrofuran
Liquid
A*
<100F
<100F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Tetrahydrofuran
Disc Materials
Seat/Disc Materials
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
EPDM
A*
Liquid
A*
PTFE
A*
Triacetin
Liquid
A*
PTFE
<100F
A*
Triacetin
Liquid
<100F
A*
EPDM
<100F
A*
Tributoxy Ethyl
Phosphate
Liquid
<160F
A*
EPDM
A*
A*
PTFE
A*
A*
A*
A*
A*
A*
<140F
A*
<140F
A*
A*
A*
A*
A*
NDI
AI
BR
316
SS
Liquid
A*
Tetralin
Liquid
A*
Thionyl Chloride
Liquid
A*
PTFE
Thionyl Chloride
Liquid
A*
PTFE
Titanium
Tetrachloride
Liquid
A*
Titanium Sulfate
Solid
A*
PTFE
Titanium Sulfate
Solid
A*
PTFE
<140F
Toluene
Liquid
A*
100%,<100F
Toluene
Liquid
A*
100%,<100F
Toluene
Liquid
Toluene
Liquid
A*
Transmission Fluid
Liquid
A*
Triacetin
Liquid
Triacetin
Tributoxy Ethyl
Phosphate
Condition
<75F
100%,<100F
100%,<100F
<100F
Liquid
DI
Coating
Tributoxy Ethyl
Phosphate
Liquid
Tributoxy Ethyl
Phosphate
Liquid
Tributyl Phosphate
Liquid
Trichloracetic Acid
Solid
A*
PTFE
Trichloracetic Acid
Solid
A*
PTFE
Trichloroethane
Liquid
<140F
A*
PTFE
Trichloroethane
Liquid
<140F
A*
Trichloroethane
Liquid
A*
Trichloroethane
Liquid
Trichloroethylene
Trichloroethylene
<160F
A*
PTFE
A*
EPDM
A*
EPDM
140F
<160F
<160F
Liquid
A*
Liquid
A*
<75F
Condition
100%,<100F
A*
PTFE
<160F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
NBR
Corrosive
Media
Physical
State
Trichloroethylene
Liquid
Trichloroethylene
Liquid
Tricresyl Phosphate
Disc Materials
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
A*
DI
NDI
AI
BR
316
SS
A*
A*
Liquid
A*
Triethanol Amine
Liquid
A*
Triethanol Amine
Liquid
A*
Triethanol Amine
Liquid
<140F
A*
Triethanol Amine
Liquid
<140F
A*
Triethyl Borane
Liquid
A*
PTFE
Triethyl Borane
Liquid
A*
PTFE
Trinitroltoluene (TNT)
Liquid
A*
Trinitrotoluene (TNT)
Liquid
A*
Triphenyl Phosphate
Liquid
Triphenyl Phosphate
Liquid
A*
Condition
<75F
Coating
Condition
<160F
<140F
<140F
<160F
<100F
Liquid
A*
Turpentine
Liquid
A*
Turpentine
Liquid
Turpentine
Liquid
Urea
Solid
Urea
Solid
Urea
Solid
Urea
<75F
<75F
A*
A*
<105F
A*
A*
<105F
A*
Solid
A*
Liquid
A*
A*
Varnish
Liquid
A*
A*
Vinegar
Liquid
A*
A*
Vinyl Acetate
Solid
A*
A*
<100F
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Vinyl Acetate
Solid
Vinyl Chloride
Gas
Disc Materials
Condition
DI
NDI
AI
BR
Seat/Disc Materials
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
UHMWPE
A*
A*
316
SS
Coating
Condition
A*
A*
Liquid
A*
A*
Liquid
A*
Water, Brackish
Liquid
A*
A*
Water, Carbonated
Liquid
A*
A*
Water, Chilled
Liquid
A*
A*
Water, Chlorine
Liquid
A*
Water, Chlorine
Saturated
Liquid
Water, Chlorine
(High Content)
Liquid
A*
Water, Cooling
Liquid
Water, Deionized,
Demineralized
Liquid
Water, Distilled
Water Base
Hydraulic Oil (See
Hydraulic Oil, Water
Bas)
Liquid
A*
UHMWPE
A*
A*
A*
A*
A*
A*
A*
A*
Liquid
A*
A*
Water, Fresh
Liquid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Liquid
A*
A*
Water, Swimming
Pool (Chlorinated)
Liquid
A*
A*
Waxes
Solid
A*
A*
Whiskey
Liquid
A*
A*
White Liquor
Liquid
A*
A*
Wine
Liquid
A*
A*
Wood Alcohol
Liquid
A*
A*
Liquid
A*
A*
<4%
<4%
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.
Corrosive
Media
Physical
State
Disc Materials
Condition
Seat/Disc Materials
DI
NDI
AI
BR
316
SS
Coating
Condition
EPDM
NBR
FKM
PTFE
S20/21
PTFE
S22/23
A*
UHMWPE
Liquid
A*
A*
Xylene
Liquid
A*
Xylene
Liquid
A*
A*
Xylindenes
Liquid
A*
A*
Zinc Acetate
Solid
A*
A*
Zinc Chloride
Solid
A*
<5%,<70F
A*
Zinc Chloride
Solid
A*
<75%,<300F
A*
Zinc Cyanide
Solid
A*
A*
Zinc Hydrosulfite
Solid
A*
A*
Zinc Nitrate
Solid
Zinc Sulfate
Solid
<140F
A*
N
A*
A*
N
A*
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed
written consent of BRAY INTERNATIONAL, Inc.
The technical data herein is for general information only. Product suitability should be based solely upon customers
detailed knowledge and experience with their application.