Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Issue
1.0
Date
2014-07-23
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
Issue
Description
Author
2013-12-26
V1.0
Huang Jianbing
(employee ID:
00206028)
2014-03-19
2014-4-8
2014-4-16
ii
Contents
Contents
About This Document ............................................................................................................... ii
1 Introduction .............................................................................................................................. 1
2 Application Overview ............................................................................................................. 2
3 Product Configurations ........................................................................................................... 3
3.1 Hardware Configurations ....................................................................................................................................... 3
3.1.1 UMPT Selection Principles ................................................................................................................................. 4
3.1.2 LBBP Selection Principles .................................................................................................................................. 4
3.1.3 RRU Selection Policies ....................................................................................................................................... 5
3.1.4 Networking Reference Configurations................................................................................................................. 7
3.1.5 User Quantity Configuration Principles ............................................................................................................... 9
3.2 Basic Configurations ........................................................................................................................................... 10
3.2.1 Outdoor Mini Box (OMB) ................................................................................................................................ 10
3.2.2 BBU Box........................................................................................................................................................... 11
3.2.3 UPEUc .............................................................................................................................................................. 11
3.2.4 Processing Module ........................................................................................................................................... 12
3.2.5 RF Module ....................................................................................................................................................... 16
3.2.6 External Filter................................................................................................................................................... 22
3.2.7 Auxiliary Devices ............................................................................................................................................. 23
3.3 Site Materials Configurations............................................................................................................................... 23
3.4 Auxiliary Materials Configurations ...................................................................................................................... 25
3.5 Software Configurations ...................................................................................................................................... 27
3.6 Examples of Typical Configurations..................................................................................................................... 38
3.6.1 Typical Configurations of LBBPd2 and UMPT Boards Working with 4T4R RRUs ............................................ 38
3.6.2 Typical Configurations of LBBPd2 and UMPT Boards Working with 2T2R RRU3251 Modules ........................ 41
iii
1 Introduction
Introduction
2 Application Overview
Application Overview
Huawei launches eLTE2.2 DBS3900 LTE TDD (referred to as DBS3900 in this document),
which is an enterprise-oriented LTE product integrating wireless platform resources and
diverse technologies.
Based on Huawei advanced SingleRAN platform, the DBS3900 consists of two types of basic
function modules: baseband unit (BBU) (referred to as the BBU3900 in this document) and
remote radio unit (RRU). The BBU3900 is characterized by its small floor area, easy
installation, and low power consumption. Therefore, the BBU3900 can be easily installed in
the same place as an existing site. The RRU is compact and light. It can be installed near an
antenna to reduce feeder loss and improve system coverage.
Flexible combinations of the basic modules and auxiliary devices provide diverse site
solutions, which can meet customers' requirements for fast network construction.
3 Product Configurations
Product Configurations
Universal main processing and transmission unit (UMPT): UMPTa6 and UMPTb2
The UMPTb2, UMPTa6, and LBBPd2 or LBBPd4 boards are inserted in the BBU box. When
the DBS3900 is deployed outdoors, the BBU3900 is installed in an outdoor power cabinet
APM30H. When the DBS3900 is deployed indoors, the BBU3900 can be installed in any
standard cabinet or rack that is 19-inch wide and 2-U high.
All the RRUs can be installed on walls or poles. They are delivered with mounting kits.
The DBS3900 supports a maximum of 18 cells. (In this version, a maximum of 12 sectors in
the single-carrier scenario and a maximum of six sectors in the dual-carrier scenario are
supported. In multi-RRU co-cell scenario, one LBBP board supports a maximum of three
logical cells operating at a 5 MHz bandwidth.) The DBS3900 supports the configuration of
one cell, three cells, or six cells operating at a scalable bandwidth of 5 MHz, 10 MHz, 15
MHz, and 20 MHz or at a hybrid bandwidth. In the dual-carrier scenario, if two frequency
bands are configured, the DBS3900 supports only the dual-band + dual-carrier configuration
but not the dual-band + dual-carrier per band configuration. In the single-band + single-carrier
configuration, the RRU3232 or RRU3252 supports the 2T2R configuration and the maximum
S222222 configuration. In the dual-carrier scenario, the DBS3900 also supports the
configuration of one cell, three cells, or six cells operating at a scalable bandwidth of 5 MHz,
10 MHz, 15 MHz, and 20 MHz. For details about the bandwidth specifications of each RRU
module, see Table 3-1. An LBBP board supports only hybrid bandwidth configuration but not
hybrid multiple-input multiple-output (MIMO) configuration.
All macro RRUs (including the RRU3232, RRU3252, and RRU3251) can be installed on
walls or poles. They are delivered with mounting kits.
3 Product Configurations
In eLTE2.2 and later versions, the UMPTb2 is preferred and the UMPTa6 is optional.
The configuration principles of UMPT boards for the capacity expansion of existing sites
are as follows:
If the onsite version is upgraded to eLTE2.2 or later, and new sites are deployed for
capacity expansion, the UMPTb2 is preferred.
If the onsite version is not upgraded to eLTE2.2 or later, the UMPTa6 is preferred.
Specification
Policy
UMPTa6/UMPTb2
1.5 Gbit/s
Configuring four LBBP boards for a single BBU causes risks. If this configuration is
required, contact Huawei R&D engineers to evaluate the risks before the configuration.
In common scenarios, the LBBPd2 is delivered. In the multi-RRU co-cell scenario, the
LBBPd4 is delivered.
In eLTE2.2 or later, the same LBBPd2 supports the combination of different bandwidths.
The capability of supporting the combination of different bandwidths is not affected by
the number of carriers supported by the RRUs. For details about the number of cells
supported by each LBBP board type, see Table 3-2.
Version
LBBPd2
eLTE2.2
LBBPd4
eLTE2.2
Specification
Policy
2T/2R
4T4R
8T8R
M1 x 5 MHz + M2
x 10 MHz + M3 x
15 MHz + M4 x
20 MHz
M1 x 5 MHz +
M2 x 10 MHz +
M3 x 15 MHz +
M4 x 20 MHz
Not
supported
Preferred
M1 + M2 + M3 +
M4 3
M1 + M2 + M3
+ M4 3
6 x 5 MHz
3 x 5 MHz
N/A
3 Product Configurations
The RRU3251 is preferred for the 2T2R networking with the 2.3 GHz band.
The RRU3252 is preferred for the 4T4R networking with the 2.3 GHz or 2.5/2.6 GHz
band. The RRU3252 is also preferred for the 2T2R networking with the 2.5/2.6 GHz
band.
The AC RRU3252 is optional only when the band is 2.3 GHz. Manual quotation
supports the mixed configuration of AC RRU3252 and DC RRU3252 modules, whereas
the configurator does not.
4T4R RRUs include the RRU3252 and RRU3232. An RRU can function as two 2T2R
RRUs.
Frequency
Band
Supported
Bandwidth
Transmit
Power
Optional
Transmit Power
Multi-Carrier Bandwidth
Combinations Supported
in eLTE2.2
RRU3232
1.8 GHz
5 MHz, 10M
MHz, 15
MHz, 20
MHz
4 x 20 W
10 W or 20 W
4x 10 W
(3.5
GHz/3.7
GHz)
10 W (3.5 GHz/3.7
GHz)
10 MHz, 15
MHz, 20
MHz
2 x 40 W
or 2 x 50
W
10 W, 20 W, 30 W,
40 W
5 MHz, 10
MHz, 15
MHz, 20
MHz
4 x 20 W
10 W or 20 W
2.3 GHz
2.5 GHz/2.6
GHz
3.5 GHz/3.7
GHz
RRU3251
RRU3252
2.3 GHz
2.3 GHz
2.5 GHz/2.6
GHz
Restricted when
the transmit power
is 50 W
3 Product Configurations
Frequency
Band
Supported
Bandwidth
Multi-Carrier Bandwidth
Combinations
Supporting CPRI
Compression in eLTE2.2
Multi-Carrier Bandwidth
Combinations for Which
CPRI Compression Is
Enabled in eLTE2.2
RRU3251
2.3 GHz
10 MHz, 15
MHz, 20
MHz
N/A
RRU3252
2.3 GHz
5 MHz, 10
MHz, 15
MHz, 20
MHz
2.5 GHz/2.6
GHz
The configuration algorithm calculates the number of increased base RRUs based on the
number of installed base RRUs that can be reused regardless of whether the RRU board
type is changed. If installed base RRUs will not be reused in certain circumstances,
contact Huawei R&D engineers.
Capacity expansion supports the mixed configuration of 2.3 GHz AC RRU3252 modules
and 2.3 GHz DC RRU3252 modules. If the power supply will be changed after capacity
expansion, only increased base RRUs are delivered, and installed base RRUs on the live
network will not be replaced.
The configurator does not support the mixed configuration of different types of
intra-frequency RRUs. RRUs with different power supplies are also regarded as different
types of RRUs. (You can manually configure such RRUs if the mixed configuration is
required.)
The RRU inter-band configuration is supported only in eLTE2.2 or later and when the
LBBPd2 is used.
A single RRU supports a maximum of two carriers and a single BBU supports a
maximum of 18 cells.
RRUs of different frequency bands can be connected to the same LBBP board, and the
maximum number of cells supported by the LBBP board remains unchanged. Currently
the LBBPd4 does not support the RRU inter-band configuration.
Cells served by the same LBBP board must all be 2T2R cells or 4T4R cells (including
cells served by RRUs on different bands and RRUs on the same band). The number of
TX and RX channels supported by each LBBP board can be different in the same BBU.
However, the number of TX and RX channels supported by each of the two carriers must
be the same in the same RRU.
The enabling or disabling of CPRI compression must be consistent for all RRUs
connected to the same LBBP board. The RRU3232 does not support CPRI compression.
3 Product Configurations
The license for CPRI compression must be centrally configured for the different carriers
of the same RRU. If the CPRI compression feature is selected, the algorithm of the
configurator calculates the number of RRU optical modules and the number of CPRI
compression licenses based on the assumption that CPRI compression is enabled for all
RRUs supporting CPRI compression.
The bandwidths of carriers for the same LBBP board can be different.
One 4T4R RRU3232/RRU3252 can function as two 2T2R RRUs. The remote electrical
tilt (RET) feature is not allowed on an RRU that functions as two RRUs.
Bandwidth
Number
of Cells
Number
of LBBP
Boards
RRU Type
LBBPd2
Description
Number of
4T4R RRUs
Number of
RRU3251 Modules
5 MHz/10
MHz/15
MHz/20 MHz
Minimum
configuration
LBBPd2
5 MHz/10
MHz/15
MHz/20 MHz
Typical
configuration
LBBPd2
5 MHz/10
MHz/15
MHz/20 MHz
18
18
Maximum
configuration
Bandwidth
Number of
Cells
Number of
LBBP Boards
Number of
4T4R RRUs
Description
LBBPd2
5 MHz/10 MHz/15
MHz/20 MHz
Minimum
configuration
LBBPd2
5 MHz/10 MHz/15
MHz/20 MHz
Typical
configuration
LBBPd2
5 MHz/10 MHz/15
MHz/20 MHz
18
18
Maximum
configuration
3 Product Configurations
Bandwidth
Number of
Logical
Cells
Number of
LBBP
Boards
Number of
2T2R
RRUs
Number of
4T4R
RRUs
Description
LBBPd4
5 MHz
None
Only 1.8 GHz RRU3232 modules are supported in the multi-RRU co-cell scenario.
The number of licenses for the cell combination feature is equal to the number (before cell
combination) of cells involved in cell combination. The sales unit is per cell.
Check Relationships Between Site Types, Common Cells, and Logical Cells
The check relationships are as follows in the multi-RRU co-cell scenario:
2T2R
Number of LBBP boards = max (Rounded Up [Number of logical cells/3.0],
Rounded Up [Number of physical cells/6.0])
4T4R
Number of LBBP boards = Rounded Up (Number of physical cells/3.0)
For details about the check relationships between the number of physical cells, number
of cells involved in cell combination, and number of logical cells, see the following
attachment:
Co-Cell Check
Rules.xls
Multi-RRU co-cell does not support inter-LBBP combination, which means that cell
combination can be performed only for RRUs connected to the same LBBP board.
Cell combination depends only on joint scheduling but not PDSCH and PUSCH space
division multiple access (SDMA).
One LBBPd4 board supports a maximum of three logical cells and the combination of
six 2T2R RRUs or three 4T4R RRUs.
Multi-RRU cells and normal cells can be served by the same LBBP board.
Cell combination supports hot ring or cascading. However, hot ring supports only the
star topology but not cascading of RRUs.
Normal cells support cold ring, hot ring, or cascading (the RRU3232 supports the
maximum two-level cascading). However, hot ring supports only the star topology but
not cascading of RRUs.
3 Product Configurations
Hot ring requires that the distance difference for the two optical fibers on the same RRU be less than 200
200 m, which means that the delay difference must be less than 4 Tc.
One 4T4R RRU can serve two combined 2T2R cells. The combination of RRU
neighboring cells refers the combination of cells served by different RRUs.
LBBPd2
LBBPd4
TX/RX
10M
15M
20M
2T2R
1800
3600
3600
3600
4T4R
1800
3600
3600
3600
2T2R/4T4R
1800
5 MHz
600
10 MHz
1200
15 MHz
1200
20 MHz
1200
Table 3-10 Number of users supported by a single cell (when the LBBPd4 is used)
Bandwidth
5 MHz
When a single LBBP board supports multiple sectors, the number of supported users is affected by the
capability of the LBBP board. When the combination of different bandwidths is supported, the number of
of RRC connected users supported by a single LBBP board is calculated based on Table 3-10, and cannot
cannot exceed the maximum number of RRC connected users (see Table 3-9) supported by a single LBBP
LBBP board.
3 Product Configurations
Description
Function
Configuration Principle
QWMB0OMBAC00
OMB Cabinet
(Ver.C,
220/110VAC)
Outdoor enhanced
assembly cabinet used
for installing BBUs. This
OMB is supplied with
220 V/110 V AC input
power.
Optional.
This item can be configured when the
BBU is installed on an outdoor pole or
on a wall.
This item supports a maximum of three
LBBP boards and two UMTP boards. It
can supply power to a maximum of six
RRUs. (This OMB cabinet is delivered
with one PSU module, and therefore
supports a maximum of three RRUs.
With one more PSU module
configured, it can support a maximum
of six RRUs. PSU is short for power
supply unit.)
This item is not sold in the United States,
Japan, Britain, or Canada.
WD2MR4850G00
PSU Module
(AC/DC)
Optional.
This item is used for outdoor DC
OMBs.
One piece is quoted when the number
of configured RRUs is greater than 3
but is less than or equal to 6. The
configuration details are as follows:
QWMB0OMBDC00
OMB Cabinet
(Ver.C,
-48VDC)
Outdoor enhanced
assembly cabinet used
for installing BBUs. This
OMB is supplied with
48V DC input power.
RRU
OMB
PSU
13
46
Optional.
This item can be configured when the
BBU is installed on an outdoor pole or
on a wall. This item supports a
maximum of three LBBP boards and
two UMTP boards. It can supply power
to a maximum of six RRUs.
This item is not sold in the United
States, Japan, Britain, or Canada.
10
3 Product Configurations
Description
Function
Configuration
Principle
WD2M048B
BU01
BBU Box
Mandatory.
The BBU box can be installed in an APM30H cabinet or OMB. If it is installed in an APM30H cabinet
(Ver.B), a maximum of three LBBP boards can be configured. If it is installed in an APM30H cabinet
(Ver.D), a maximum of four LBBP boards can be configured. If it is not installed in a cabinet, a maximum
of six LBBPd2 boards can be configured.
3.2.3 UPEUc
Table 3-13 UPEUc configurations
External
Model No.
Description
Function
Configuration Principle
WD2M000
PEU03
Universal
Power and
Environment
Interface
Unit
Used for
converting 48
V DC input
power into +12
V DC input
power and for
providing two
ports for RS485
signals and eight
ports for
Boolean signals
Optional.
11
3 Product Configurations
Description
Function
Configuration Principle
WD2D00U
MPT00
Universal
Main
Processing &
Transmission
unit with 4E1
and 2FE/GE
interface (With
Ublox Card)
UMPTa6
Mandatory.
WD2D0UM
PTB01
Universal
Main
Processing &
Transmission
unit with 4E1
and 2FE/GE
interface
UMPTb2
UMPTb2
Mandatory.
If the UMPT boards work in cold standby mode, the standby UMPT board needs to connect to the
transmission equipment and share the GPS with the UMPT board installed in slot 7. Therefore, the
transmission equipment and item 02230MAC that is used for two BBUs to share the same GPS need to be
be manually quoted.
LBBP
Table 3-15 LBBP configurations
External
Model No.
Description
Function
Configuration Principle
WD2DLBBP
D200
LTE
BaseBand
Processing
Unit d2
LBBPd2
Provides six CPRI ports.
Mandatory in scenarios
except the multi-RRU
co-cell scenario.
External
Model No.
Description
3 Product Configurations
Function
Configuration Principle
WD2D0LBB
PD00
LTE
Baseband
Processing
and Interface
Unit
LBBPd4
When the conditions for hot ring are met, hot ring is not supported if there are more than four pieces of
LBBP boards and the number of optical modules connecting to CPRI optical fibers exceeds the RRU
capability.
Description
Sales Unit
Configuration
Principle
LT1S0ACTUS0
0
per RRC
Connected
User
13
3 Product Configurations
Throughput
Table 3-17 LBBP module capacity: throughput
External Model No.
Description
Sales Unit
Configuration Principle
LT1S0THROU00
Throughput
Capacity
per Mbps
Resource Block
Table 3-18 LBBP module capacity: resource block
External Model No.
Description
Sales Unit
Configuration Principle
LT1S000RB00
Resource Block
per RB
14
3 Product Configurations
BB TX Channel
Table 3-19 LBBP module capacity: BB TX channel
External
Model No.
Description
Sales Unit
Configuration Principle
LT1S00BBT
C00
BB Transmit
Channel
per Channel
BB RX Channel
Table 3-20 LBBP module capacity: BB RX channel
External
Model No.
Description
Sales Unit
Configuration Principle
LT1S00BB
RC00
BB Receive
Channel
per Channel
15
External
Model No.
Description
3 Product Configurations
Sales Unit
Configuration Principle
In 2T2R networking, this item is not
configured.
In 4T4R networking, two pieces are
configured for each cell.
USCU
Table 3-21 USCU configurations
External
Model No.
Description
Function
Configuration
Principle
WD2D00USC
U03
Universal Satellite
card and Clock Unit
type B2(8HP),Without
Navior-24s Satellite
Card(With Install
Accessory)
Universal satellite
card and clock unit
(USCU) board
Optional.
WD2D00USC
U00
Universal Satellite
Clock Unit
USCU board
Optional.
A GPS satellite card connecting to satellite antennas is integrated into the UMPT board to receive GPS
signals.
When the GPS satellite card cannot receive satellite signals, the internal clock switches to the free-run
mode. The eNodeB can keep properly working for 8 hours in this mode.
3.2.5 RF Module
RRU
Table 3-22 RF module configurations
External
Model No.
Description
Function
Configuration Principle
QL4PRRU3
2300
RRU 3232
Module(2.3G
Optional.
16
External
Model No.
Description
Function
Hz)
QL4PRRU3
2500
QL4PRRU3
1800
QL4PRRU3
18AC
QL4PRRU3
3500
QL4PERRU
3700
QL4PRRU5
2300
RRU 3232
Module(2.5/2.
6GHz)
RRU 3232
Module(1.8G
Hz)
RRU
Module(1.8G
Hz)(AC)
RRU 3232
Module(3.5G
Hz)
eRRU 3232
Module(3.7G
Hz)
RRU 3251
Module(2.3G
Hz)
3 Product Configurations
Configuration Principle
modules is determined by the
number of cells and the frequency
bands.
Each RRU3232 supports one 4T4R
sector or two 2T2R sectors.
Optional.
17
External
Model No.
Description
3 Product Configurations
Function
Configuration Principle
S111@20MHz site.
LT1PRRU2
2300
LT1PRRU2
2301
LT1PRRU2
2500
RRU 3252
Module(2.3G
Hz DC)
RRU 3252
Module(2.3G
Hz AC)
RRU 3252
Module(2.5G
Hz/2.6GHz,
DC)
Optional.
Optional.
RF Multi Carrier
Table 3-23 RF module capacity: RF multi carrier
External
Model No.
Description
Sales Unit
Configuration Principle
LT1ST00M
CA00
RF Multi
Carrier
per Carrier
18
External
Model No.
Description
3 Product Configurations
Sales Unit
Configuration Principle
used, three pieces are configured if the S222
configuration is used, and six pieces are
configured if the S333 configuration is
used.
RF Output Power
Table 3-24 RF module capacity: RF output power
External
Model No.
Description
Sales
Unit
Configuration Principle
LT1S0000P
A00
RF Output
Power
per 20W
Carrier Bandwidth
Table 3-25 RF module capacity: carrier bandwidth
External
Model No.
Description
Sales Unit
Configuration Principle
LT1S005M
HZ00
Carrier
Bandwidth 0~5 MHz
per cell
19
External
Model No.
Description
3 Product Configurations
Sales Unit
Configuration Principle
the quantity of this item required for each
carrier must be calculated separately.
This item is mandatory, and its quantity is
summarized by site.
LT1S010M
HZ00
Carrier
Bandwidth 5~10 MHz
per cell
LT1S015M
HZ00
Carrier
Bandwidth 10~15 MHz
per cell
LT1S020M
HZ00
Carrier
Bandwidth 15~20 MHz
per cell
RF Transmit Channel
Table 3-26 RF module capacity: RF transmit channel
External
Model No.
Description
Sales Unit
Configuration Principle
LT1S00RFT
C00
RF Transmit
Channel
per Channel
20
External
Model No.
Description
3 Product Configurations
Sales Unit
Configuration Principle
one RRU 2)
The configuration of this item is not
affected by the number of carriers. This
item may be required in 4T4R or 2T2R
networking.
RF Receive Channel
Table 3-27 RF module capacity: RF receive channel
External
Model No.
Description
Sales Unit
Configuration Principle
LT1S00RFR
C00
RF Receive
Channel
per
Channel
21
3 Product Configurations
Description
Function
Configuration Principle
*****
AUF
Auxiliary
metal filter
External
metallic
auxiliary
filter
(AUF)
Optional.
This item can be a single-passband external
AUF used for 2T2R networking and 4T4R
networking or a dual-passband external
AUF used for 2T2R networking.
The configuration principles are as follows:
AUF
Auxiliary
dielectric
filter
External
dielectric
AUF
Optional.
This item can be a single-passband external
AUF used for 2T2R networking and 4T4R
networking or a dual-passband external
AUF used for 2T2R networking.
The configuration principles are as follows:
22
3 Product Configurations
Description
Function
Configuration Principle
E000DKBA1800
18L RRU
Plastic Cover
Plastic cover
used for the
RRU3252
Optional.
One piece is configured for
each RRU3252.
Manual quotation is required.
E000DKBA1200
12L RRU
Plastic Cover
Plastic cover
used for the
RRU3251
Optional.
One piece is configured for
each RRU3251.
Manual quotation is required.
Description
Function
Configuration Principle
LTIP000FBR
00
Optical Fiber
Optical fibers
used for
connecting to
other
equipment
over the S1 or
X2 interface
Optional.
QWMP0000F
E00
Ethernet
Cable
Ethernet
cables used
for
connecting to
other
equipment
over the S1 or
X2 interface
Optional.
WD5PRRUC
P000
RRU Cable
Package
Package
containing
power cables
used for DC
RRUs
Mandatory.
WD5PRRUC
Pxxx
AC RRU
Cable
Package
Package
containing
power cables
used for AC
Mandatory.
23
External
Model No.
Function
Configuration Principle
RRUs
Optical fibers
used for
installing
multimode
optical
modules that
support a
CPRI rate of
4.9 Gbit/s
Optional.
CPRI Optical
Transmission
Materials
(4.9G)
(Single
Mode)
Optical fibers
used for
installing
single-mode
optical
modules that
support a
CPRI rate of
4.9 Gbit/s
Optional.
Jumper
1/2"(sector)
Top-of-cabine
t jumper used
for RRUs
Optional.
WD5P0INSM
T03
Installation
Materials for
DBS3900
Package
containing
materials used
for installing
the DBS3900
Mandatory.
QL4POMBIS
00
OMB
Installation
Package
Package
containing
materials used
for installing
OMBs
Optional.
WD5P49CPR
I02
WD5P49CPR
I01
A12FEED00
Description
3 Product Configurations
CPRI Optical
Transmission
Materials
(4.9G)
24
3 Product Configurations
Description
Function
Configuration Principle
A000GPS0
4
GPS Antenna
AGPSGLO
02
CDMA &
WiMAX &
LTE BTS
GPS/GLONA
SS
Antenna/Feed
er System
E000IGU00
Grounding
Unit
Ground unit
Optional.
Indoor Cable
Ladder(2.5m)
Optional.
WDCDBO
X01
Outdoor
Cable
Ladder(2.5m)
Optional.
GM1X0DN
SPE00
Embedded
Environment
Monitoring
Unit
Package
containing the
environment
monitoring unit
(without sensors)
Optional.
QW1XEM
EUWS00
Embedded
Environment
Monitoring
Unit (with
Package
containing the
environment
monitoring unit
Optional.
E000ICL00
25
External
Model No.
3 Product Configurations
Description
Function
Configuration Principle
Sensors)
(with sensors)
LT1PRRU
CEP00
RRU Cable
Extension
Package(50m
-100M)
Extension package
containing RRU
cables (50100 m)
used for
WiMAX/LTE
Optional.
TD1MDCD
U12B0
DCDU-12B
DC power
distribution unit
used for providing
one 48 V DC
power input and
ten 48 V DC
power outputs (30
A)
Optional.
GM5M000
SPD00
AC surge
protection
box
Optional.
GM5M000
SPM00
AC Lighting
Protection
Box
Optional.
GM5X00S
LPU00
BTS3900,
GM5Z1SLPU
, Monitoring
Signal
Lightning
Protection
Unit
Optional.
This item is a standard 1-U high
and19-inch wide device. One piece is
configured when the BBUs of the
DBS3900 are installed outdoors and
1 to 16 Boolean alarms need to be
supported.
26
3 Product Configurations
Description
Sales Unit
Configuration Principle
LT1STBASIC06
eNodeB TDD
Basic
Software,
V100R006
per cell
Description
Sales Unit
Configuration Principle
LT1STUSLTE04
per cell
Description
Sales Unit
Configuration
Principle
Dependency
LT1STD2I2
O00
DL 2x2
MIMO
per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
LT1ST00SU
E00
Support of
UE
Category2/3/
4
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
LT1SSGST
RB00
Single
Streaming
Beamforming
per cell
This item is
configured based on
the total number of
27
External
Model No.
Description
Sales Unit
3 Product Configurations
Configuration
Principle
Dependency
transmission mode.
This feature does not apply when
eNodeBs operate at a bandwidth of 5
MHz.
This feature cannot be enabled at the
same time as the following features:
TDLOFD-001031 Extended CP
LT1STU4A
RD00
UL
4-Antenna
Receive
Diversity
per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
LT1SULMU
MI01
UL 2 x4
MU-MIMO
per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
TDLOFD-001015 Enhanced
Scheduling
TDLOFD-001005 UL 4-Antenna
Receive Diversity
LT1ST0UIR
C00
UL
Interference
Rejection
Combining
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1STCCIR
C00
Control
Channel IRC
per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
TDLBFD-00202001 UL 2-Antenna
28
External
Model No.
Description
Sales Unit
Configuration
Principle
which this item is
configured.
LT1ST00SF
N00
LT1SADAS
FN00
SFN
Adaptive
SFN/SDMA
per cell
Per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
This item is
configured based on
the total number of
physical cells at each
site by default. You
can manually modify
the number of cells
for which this item is
configured.
3 Product Configurations
Dependency
Receive Diversity
TDLOFD-001005 UL 4-Antenna
Receive Diversity
TDLOFD-001031 Extended CP
TDLOFD-001039 RF Channel
Intelligent Shutdown
TDLOFD-001066 Intra-eNodeB UL
CoMP
LT1STUCO
MP00
Intra-eNodeB
UL CoMP
per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
TDLBFD-00100701
uplink-downlink subframe
configuration type1&2 (this feature
does not support the
uplink-downlink subframe
configuration 1)
TDLOFD-001031 Extended CP
TDLOFD-001039 RF Channel
Intelligent Shutdown
TDLOFD-001066 Intra-eNodeB UL
CoMP
TDLOFD-001075 SFN
29
External
Model No.
Description
Sales Unit
Configuration
Principle
3 Product Configurations
Dependency
TDLOFD-002008 Adaptive
SFN/SDMA
Optional
uplink-downl
ink subframe
configuration
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1ST0ESC
H00
Enhanced
Scheduling
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
None.
LT1ST00TP
E00
TCP Proxy
Enhancer(TP
E)
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
None.
LT1ST00A
QM00
Active Queue
Management(
AQM)
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
None.
30
External
Model No.
Description
Sales Unit
Configuration
Principle
3 Product Configurations
Dependency
supported RRC
connected users needs
to be increased.
LT1ST00EA
C00
Enhanced
Admission
Control
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
LT1ST0FX
US00
Flexible User
Steering
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
LT1STUPA
BS00
UL
Pre-allocation
Based on
SPID
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
LT1STDNG
PB00
DL
Non-GBR
Packet
Bundling
per cell
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
None.
LT1STCPRI
CPRI
per cell
This item is
31
External
Model No.
Description
C00
Compression
LT1ST0DD
RX00
LT1STCC00
000
LT1ST00HS
M00
LT1ST0UH
SM00
LT1STETQ
OS00
Dynamic
DRX
Cell
Combination
High Speed
Mobility
Ultra High
Speed
Mobility
Enhanced
Transmission
QoS
Sales Unit
per cell
per cell
per cell
per cell
per eNodeB
3 Product Configurations
Configuration
Principle
Dependency
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
This item is
configured based on
the total number of
cells at each site by
default. You can
manually modify the
number of cells for
which this item is
configured.
One piece is
configured for each
site.
32
External
Model No.
Description
3 Product Configurations
Sales Unit
Configuration
Principle
Dependency
per eNodeB
One piece is
configured for each
site.
Management
LT1ST0IPP
M00
IP
Performance
Monitoring
LT1SIPAP
M000
IP Active
Performance
Measurement
per eNodeB
This item is
configured based on
the total number of
sites. More pieces can
be added for capacity
expansion.
None.
LT1ST0ES
YN00
Enhanced
Synchronizati
on
per eNodeB
One piece is
configured for each
site.
LTISTDTP
QG00
Different
Transport
Paths based
on QoS
Grade
per eNodeB
One piece is
configured for each
site.
LT1ST00V
RF00
Virtual
Routing &
Forwarding
per VRF
Domain
This item is
configured based on
the number of VRF
domains by default.
You can manually
modify the number of
VRF domains for
which this item is
configured.
LT1STSME
CH00
Security
Mechanism
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
TDLOFD-003005 OM Channel
Backup
TDLOFD-003009 IPsec
TDLOFD-003012 IP Performance
Monitoring
TDLOFD-00301302 IEEE1588 V2
Clock Synchronization
33
External
Model No.
Description
Sales Unit
Configuration
Principle
3 Product Configurations
Dependency
IPsec
per eNodeB
One piece is
configured for each
site.
LT1ST00PK
I00
Public Key
infrastructure
(PKI)
per eNodeB
One piece is
configured for each
site.
LT1STINFI
R00
Integrated
Firewall
per eNodeB
One piece is
configured for each
site.
None.
LT1ST00A
CC00
Access
Control based
on 802.1x
per eNodeB
One piece is
configured for each
site.
LT1STSFLE
X00
S1-flex
per eNodeB
One piece is
configured for each
site.
LT1ST0EO
AM00
Ethernet
OAM
per eNodeB
One piece is
configured for each
site.
LT1ST0OM
CB00
OM Channel
Backup
per eNodeB
One piece is
configured for each
site.
LT1ST0IPR
B00
IP Route
Backup
per eNodeB
One piece is
configured for each
site.
34
3 Product Configurations
External
Model No.
Description
Sales Unit
Configuration
Principle
Dependency
LT1ST00BF
D00
Bidirectional
Forwarding
Detection
per eNodeB
One piece is
configured for each
site.
LT1ST00EL
A00
Ethernet Link
Aggregation(
IEEE
802.3ad)
per eNodeB
One piece is
configured for each
site.
LT1ST00A
NR00
Automatic
Neighbor
Relation(AN
R)
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1STPCIS
O00
PCI Collision
Detection &
Self-Optimiz
ation (per
Cell)
per cell
LT1ST0ILL
B00
Intra-LTE
Load
Balancing
LT1SEILTL
B00
Enhanced
Intra-LTE
Load
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
per RRC
Connected
User
This item is
configured based on
the total number of
RRC connected users
at each site. More
pieces can be added
when the number of
supported RRC
connected users needs
to be increased.
per RRC
Connected
User
This item is
configured based on
the total number of
None.
35
External
Model No.
Description
Sales Unit
Balancing
Configuration
Principle
3 Product Configurations
Dependency
LT1ST00M
RO01
Mobility
Robust
Optimization(
MRO)
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
None.
LT1ST00AF
D00
Antenna
Fault
Detection
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
None.
LT1ST0CO
DC00
Cell Outage
Detection and
Compensatio
n
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1STRFCI
S00
RF Channel
Intelligent
Shutdown
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
36
External
Model No.
Description
Sales Unit
Configuration
Principle
3 Product Configurations
Dependency
TDLOFD-001075 SFN
TDLOFD-002008 Adaptive
SFN/SDMA
TDLOFD-070230 Cell
Combination
LT1ST0LPC
M00
Low Power
Consumption
Mode
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1ST00PC
M00
Power
Consumption
Monitoring
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1ST0DBI
S00
Intelligent
Power-Off of
Carriers in
the Same
Coverage
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
LT1ST0PIS
M00
PSU
Intelligent
Sleep Mode
per cell
This item is
configured based on
the total number of
cells at each site. You
are not allowed to
manually modify the
number of cells for
which this item is
configured.
LT1ST00SP
S00
Symbol
Power Saving
per cell
This item is
configured based on
the total number of
cells at each site. You
are not allowed to
manually modify the
number of cells for
37
External
Model No.
Description
Sales Unit
3 Product Configurations
Configuration
Principle
Dependency
Intelligent
Battery
Management
per cell
This item is
configured based on
the total number of
cells at each site. You
are not allowed to
manually modify the
number of cells for
which this item is
configured.
LT1ST0RE
TC00
Remote
Electrical Tilt
Control
per cell
This item is
configured based on
the total number of
cells at each site by
default. You are not
allowed to manually
modify the number of
cells for which this
item is configured.
Number
Number
Number
Number
Number
Number
Number
Number
Number of
of LBBPd2
of UMPT
of UPEUc
of UEIU
of USCU
of UFLPb
of SLPU
of 4T4R
CPRI SFPs
Boards
Boards
Modules
Modules
Boards
Modules
Modules
RRUs
(Unit: Pair)
O1,2T2R, 10M
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
38
3 Product Configurations
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
S111, 2T2R,
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
1~2
1~2
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
10M
S111, 2T2R,
20M
S111, 4T4R,
10M
S111, 4T4R,
20M
S1111, 2T2R,
10M
S1111, 2T2R,
20M
S1111, 4T4R,
10M
S1111,4T4R,
20M
S11111, 2T2R,
10M
S11111, 2T2R,
20M
S11111, 4T4R,
10M
S11111, 4T4R,
20M
S111111, 2T2R,
10M
S111111, 2T2R,
20M
S111111, 4T4R,
10M
S111111, 4T4R,
20M
S2, 2T2R,
5M+5M or
5M+10M or
10M+10M or
10M+20M or
20M+20M or
39
3 Product Configurations
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
12
12
1 (optional)
1 (optional)
1 (optional)
1 (optional)
5M+5M or
5M+10M or
10M+10M
S2, 4T4R,
10M+20M or
20M+20M
S22, 2T2R,
5M+5M or
5M+10M or
10M+10M or
10M+20M or
20M+20M
S22, 4T4R,
5M+5M or
5M+10M or
10M+10M
S22, 4T4R,
10M+20M or
20M+20M
S222, 2T2R,
5M+5M or
5M+10M or
10M+10M or
10M+20M or
20M+20M
S222, 4T4R,
5M+5M or
5M+10M or
10M+10M or
S222, 4T4R,
10M+20M or
20M+20M
6.144 Gbit/s SFP optical modules are used for CPRI ports.
40
3 Product Configurations
Number
of LBBPd2
Boards
Number
of UMPT
Boards
Number
of UPEUc
Modules
Number of
USCU
Boards
Number of
RRU3251
Modules
Number of
CPRI SFPs
(Unit: Pair)
O1, 2T2R,
5M/10M/20M
12
12
1 (optional)
S11, 2T2R,
5M/10M/20M
12
12
1 (optional)
S111, 2T2R,
5M/10M/20M
12
12
1 (optional)
S1111, 2T2R,
5M/10M/20M
12
12
1 (optional)
S11111, 2T2R,
5M/10M/20M
12
12
1 (optional)
S111111, 2T2R,
5M/10M/20M
12
12
1 (optional)
S222, 2T2R,
5M+5M or
5M+10M or
10M+10M or
10M+20M or
20M+20M
12
12
1 (optional)
S222, 4T4R,
5M+5M or
5M+10M or
10M+10M or
12
12
1 (optional)
S222, 4T4R,
10M+20M or
20M+20M
12
12
1 (optional)
6.144 Gbit/s SFP optical modules are used for CPRI ports.
Table 3-37 Typical hardware configuration example 1: S111, 10 MHz, 2T2R (LBBPd2 boards
and 2 x 40 W RRU3251 modules are used)
Basic Hardware/Software
Package
BBU Box
41
3 Product Configurations
Basic Hardware/Software
Package
Throughput Capacity
Resource Block
150
RF Output Power
Table 3-38 Typical hardware configuration example 2: S222, 20 MHz + 20 MHz, 2T2R (LBBPd2
boards and 2 x 40 W RRU3251 modules are used)
Basic Hardware/Software
Package
BBU Box
Throughput Capacity
Resource Block
600
RF Multi Carrier
RF Output Power
42
3 Product Configurations
Table 3-39 Typical hardware configuration example 3: S111, 20 MHz, 4T4R (LBBPd2 boards
and 4 x 20 W RRU3232 or RRU3252 modules are used)
Basic Hardware/Software Package
BBU Box
Throughput Capacity
Resource Block
300
BB Transmit Channel
BB Receive Channel
RF Multi Carrier
RF Output Power
RF Transmit Channel
RF Receive Channel
Table 3-40 Typical hardware configuration example 4: S222, 20 MHz + 20 MHz, 4T4R (LBBPd2
boards and 4 x 20 W RRU3232 or RRU3252 modules are used)
Basic Hardware/Software
Package
BBU Box
43
3 Product Configurations
Basic Hardware/Software
Package
Throughput Capacity
Resource Block
600
BB Transmit Channel
12
BB Receive Channel
12
RF Multi Carrier
RF Output Power
RF Transmit Channel
RF Receive Channel
44
Number of
Modules in the 3
x 10 MHz
Configuration
Number of
Modules Added in
the 3 x 20 MHz
Configuration
Configuration Principle
Remarks
BBU Box
The existing
hardware should
be reused.
LTE
BaseBand
Processing
Unit
The existing
hardware should
be reused.
LTE Main
Processing
&
Transmissio
n Unit
The existing
hardware should
be reused.
RRC
Connected
User
Configured based
on the network
planning results
None.
Throughput
Capacity
Configured based
on the network
planning results
None.
Resource
Block
150
150
None.
45
Basic
Hardware/
Software
Package
Number of
Modules in the 3
x 10 MHz
Configuration
Number of
Modules Added in
the 3 x 20 MHz
Configuration
Configuration Principle
Remarks
Mandatory in
4T4R
networking.
The hardware
license for this
item has been
available since
eRAN3.0.
BB Receive
Channel
Mandatory in
4T4R
networking.
The hardware
license for this
item has been
available since
eRAN3.0.
RRU 3232
Module(2.3
GHz)
The existing
hardware should
be reused.
RF Multi
Carrier
None.
RF Output
Power
None.
Carrier
Bandwidth
-0~5 MHz
None.
Carrier
Bandwidth
-5~10 MHz
None.
Carrier
Bandwidth
-10
MHz~15
MHz
None.
Carrier
Bandwidth
-15
MHz~20
MHz
None.
RF
Transmit
Mandatory in
4T4R
46
Basic
Hardware/
Software
Package
Number of
Modules in the 3
x 10 MHz
Configuration
Number of
Modules Added in
the 3 x 20 MHz
Configuration
Channel
RF Receive
Channel
Configuration Principle
Remarks
not required.
networking.
The hardware
license for this
item has been
available since
eRAN3.0.
Mandatory in
4T4R
networking.
The hardware
license for this
item has been
available since
eRAN3.0.
Table 4-2 Configurations for capacity expansion from existing LBBP boards (S111, 10 MHz,
4T4R) and RRUs (4 x 20 W) used for eLTE2.1 to LBBPc boards (S111, 20 MHz, 4T4R) and
RRUs (4 x 20 W) used for eLTE2.2
Basic
Hardware/
Software
Package
Number of
Modules in the
3 x 10 MHz
Configuration
Number of
Modules Added in
the 3 x 20 MHz
Configuration
Configuration Principle
Remarks
BBU Box
The existing
hardware should
be reused.
LTE
BaseBand
Processing
Unit
Two LBBPc
boards must be
added.
LTE Main
Processing
&
Transmissio
n Unit
The existing
hardware should
be reused.
RRC
Connected
User
Configured
based on the
network planning
results
None.
Throughput
Capacity
Configured
based on the
network planning
results
None.
47
Basic
Hardware/
Software
Package
Number of
Modules in the
3 x 10 MHz
Configuration
Number of
Modules Added in
the 3 x 20 MHz
Configuration
Configuration Principle
Remarks
Resource
Block
150
150
Mandatory
BB Receive
Channel
The hardware
license for this
item has been
available since
eRAN3.0.
Mandatory in
4T4R networking.
Mandatory in
4T4R networking.
The hardware
license for this
item has been
available since
eRAN3.0.
The hardware
license for this
item has been
available since
eRAN3.0.
RRU 3232
Module(2.3
GHz)
The existing
hardware should
be reused.
RF Multi
Carrier
None.
RF Output
Power
None.
Carrier
Bandwidth
-0~5 MHz
None.
Carrier
Bandwidth
-5~10 MHz
None.
Carrier
Bandwidth
-10
MHz~15
MHz
None.
Carrier
Bandwidth
-15
MHz~20
None.
48
Basic
Hardware/
Software
Package
Number of
Modules in the
3 x 10 MHz
Configuration
Number of
Modules Added in
the 3 x 20 MHz
Configuration
Configuration Principle
Remarks
RF
Transmit
Channel
Mandatory in
4T4R networking.
RF Receive
Channel
Mandatory in
4T4R networking.
MHz
The hardware
license for this
item has been
available since
eRAN3.0.
The hardware
license for this
item has been
available since
eRAN3.0.
Table 4-3 Configurations for capacity expansion from existing LBBP boards (S111, 20 MHz,
2T2R) and RRUs (2 x 20 W) used for eRAN3.0 to LBBPd2 boards (S111, 20 MHz, 4T4R) and
RRUs (4 x 20 W) used for eRAN6.0
Basic
Hardware/
Software
Package
Number of Modules
in the 3 x 20 MHz
and 2T2R
Configuration
(eRAN3.0)
Number of Modules
Added in the 3 x 20
MHz and 4T4R
Configuration
(eRAN6.0)
Configuration Principle
Remarks
BBU Box
The existing
hardware
should be
reused.
LTE
BaseBand
Processing
Unit
LTE
BaseBand
Processing
Unit d2
One
LBBPd2
board must
be
configured
to replace
the existing
LBBP
board.
LTE Main
Processing
&
Transmissio
n Unit
The existing
hardware
should be
reused.
49
Basic
Hardware/
Software
Package
Number of Modules
in the 3 x 20 MHz
and 2T2R
Configuration
(eRAN3.0)
Number of Modules
Added in the 3 x 20
MHz and 4T4R
Configuration
(eRAN6.0)
Configuration Principle
Remarks
RRC
Connected
User
Configured based on
the network planning
results
None.
Throughput
Capacity
Configured based on
the network planning
results
None.
Resource
Block
300
Mandatory
BB
Transmit
Channel
BB Receive
Channel
The
hardware
license for
this item
has been
available
since
eRAN3.0.
Mandatory
in 4T4R
networking.
Mandatory
in 4T4R
networking.
The
hardware
license for
this item
has been
available
since
eRAN3.0.
The
hardware
license for
this item
has been
available
since
eRAN3.0.
RRU 3232
Module(2.3
GHz)
The existing
hardware
should be
reused.
RF Multi
Carrier
None.
50
Basic
Hardware/
Software
Package
Number of Modules
in the 3 x 20 MHz
and 2T2R
Configuration
(eRAN3.0)
Number of Modules
Added in the 3 x 20
MHz and 4T4R
Configuration
(eRAN6.0)
Configuration Principle
Remarks
RF Output
Power
None.
Carrier
Bandwidth
-0~5 MHz
None.
Carrier
Bandwidth
-5~10 MHz
None.
Carrier
Bandwidth
-10
MHz~15
MHz
None.
Carrier
Bandwidth
-15
MHz~20
MHz
None.
RF
Transmit
Channel
RF Receive
Channel
LTE TDD
Basic
Software
Upgrade,
V100R005
to
V100R006
None.
51
Table 4-4 Configurations for capacity expansion from LBBPs (S111, 10 MHz, 2T2R) and
RRU3232 modules (2 x 20 W) used for eRAN3.0 to LBBPs (S111, 20 MHz, 2T2R) and
RRU3251 modules (2 x 40 W) used for eRAN6.0
Basic
Hardware/
Software
Package
Number of
Modules in the 3
x 10 MHz
Configuration
Number of
Modules Added
in the 3 x 20 MHz
Configuration
Configuration Principle
Remarks
BBU Box
The existing
hardware should
be reused.
LTE
BaseBand
Processing
Unit
The existing
hardware should
be reused.
LTE Main
Processing
&
Transmissio
n Unit
The existing
hardware should
be reused.
RRC
Connected
User
Configured based
on the network
planning results
None.
Throughput
Capacity
Configured based
on the network
planning results
None.
Resource
Block
150
150
Mandatory
BB
Transmit
Channel
BB Receive
Channel
The hardware
license for this
item has been
available since
eRAN3.0.
Mandatory in
4T4R networking.
The hardware
license for this
item has been
available since
eRAN3.0.
Mandatory in
4T4R networking.
The hardware
license for this
item has been
available since
eRAN3.0.
RRU 3232
Module(2.3
The RRU3232 is
replaced with the
52
Basic
Hardware/
Software
Package
Number of
Modules in the 3
x 10 MHz
Configuration
Number of
Modules Added
in the 3 x 20 MHz
Configuration
GHz)
Configuration Principle
Remarks
not required.
RRU3251.
RRU 3251
Module(2.3
GHz)
RF Multi
Carrier
None.
RF Output
Power
None.
Carrier
Bandwidth
-0~5 MHz
None.
Carrier
Bandwidth
-5~10 MHz
None.
Carrier
Bandwidth
-10
MHz~15
MHz
None.
Carrier
Bandwidth
-15
MHz~20
MHz
None.
RF Multi
Carrier
None.
RF
Transmit
Channel
Mandatory in
4T4R networking.
RF Receive
Channel
The hardware
license for this
item has been
available since
eRAN3.0.
0
Mandatory in
4T4R networking.
The hardware
license for this
item has been
available since
eRAN3.0.
53
Table 4-5 Configurations for capacity expansion from existing LBBP boards (S111, 10 MHz,
4T4R) and RRUs (4 x 20 W) used for eRAN3.0 to LBBPd boards (S222, 20 MHz, 4T4R) and
RRUs (4 x 20 W) used for eRAN6.0
Basic
Hardware/
Software
Package
Number of
Modules in the 3
x 10 MHz
Configuration
Number of Modules
Added in the 3 x 20
MHz + 3 x 20 MHz
Configuration
Configuration Principle
Remarks
BBU Box
The existing
hardware
should be
reused.
LTE
BaseBand
Processing
Unit
One LBBPd
board is added.
LTE Main
Processing
&
Transmissio
n Unit
The existing
hardware
should be
reused.
RRC
Connected
User
Configured based
on the network
planning results
None.
Throughput
Capacity
Configured based
on the network
planning results
None.
Resource
Block
150
150
Mandatory
BB Receive
Channel
The hardware
license for this
item has been
available since
eRAN3.0.
Mandatory in
4T4R
networking.
Mandatory in
4T4R
networking.
The hardware
license for this
item has been
available since
eRAN3.0.
The hardware
license for this
item has been
available since
54
Basic
Hardware/
Software
Package
Number of
Modules in the 3
x 10 MHz
Configuration
Number of Modules
Added in the 3 x 20
MHz + 3 x 20 MHz
Configuration
Configuration Principle
Remarks
eRAN3.0.
RRU 3232
Module(2.3
GHz)
The existing
hardware
should be
reused.
RF Multi
Carrier
None.
RF Output
Power
None.
Carrier
Bandwidth
-0~5 MHz
None.
Carrier
Bandwidth
-5~10 MHz
None.
Carrier
Bandwidth
-10
MHz~15
MHz
None.
Carrier
Bandwidth
-15
MHz~20
MHz
None.
RF
Transmit
Channel
Mandatory in
4T4R
networking.
Mandatory in
4T4R
networking.
RF Receive
Channel
The hardware
license for this
item has been
available since
eRAN3.0.
The hardware
license for this
item has been
available since
eRAN3.0.
55
A-E
ANR
AUF
auxiliary filter
BBU
baseband unit
F-J
GLONASS
GPS
K-O
LBBP
MIMO
multiple-input multiple-output
OMB
OSS
P-T
PKI
PMU
PSU
RET
56
RRU
SDMA
SeGW
security gateway
U-Z
UMPT
USCU
57
58