Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
TCSM3i
DN70630644
Issue2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
Theinformationinthisdocumentissubjecttochangewithoutnoticeanddescribesonlytheproduct
defined in the introduction of this documentation. This documentation is intended for the use of
NokiaSolutionsandNetworkscustomersonlyforthepurposesoftheagreementunderwhichthe
documentissubmitted,andnopartofitmaybeused,reproduced,modifiedortransmittedinany
formormeanswithoutthepriorwrittenpermissionofNokiaSolutionsandNetworks.Thedocumentationhasbeenpreparedtobeusedbyprofessionalandproperlytrainedpersonnel,andthecustomerassumesfullresponsibilitywhenusingit.NokiaSolutionsandNetworkswelcomescustomer
commentsaspartoftheprocessofcontinuousdevelopmentandimprovementofthedocumentation.
The information or statements given in this documentation concerning the suitability, capacity, or
performanceofthementionedhardwareorsoftwareproductsaregiven"asis"andallliabilityarisinginconnectionwithsuchhardwareorsoftwareproductsshallbedefinedconclusivelyandfinally
in a separate agreement between Nokia Solutions and Networks and the customer. However,
NokiaSolutionsandNetworkshasmadeallreasonableeffortstoensurethattheinstructionscontained in the document are adequate and free of material errors and omissions. Nokia Solutions
and Networks will, if deemed necessary by Nokia Solutions and Networks, explain issues which
maynotbecoveredbythedocument.
NokiaSolutionsandNetworkswillcorrecterrorsinthisdocumentationassoonaspossible.INNO
EVENT WILL Nokia Solutions and Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT,INCIDENTALORCONSEQUENTIALORANYLOSSES,SUCHASBUTNOTLIMITEDTO
LOSSOFPROFIT,REVENUE,BUSINESSINTERRUPTION,BUSINESSOPPORTUNITYORDATA,THATMAYARISEFROMTHEUSEOFTHISDOCUMENTORTHEINFORMATIONINIT.
Thisdocumentationandtheproductitdescribesareconsideredprotectedbycopyrightsandother
intellectualpropertyrightsaccordingtotheapplicablelaws.
NSN is a trademark of Nokia Solutions and Networks. Nokia is a registered trademark of Nokia
Corporation.Otherproductnamesmentionedinthisdocumentmaybetrademarksoftheirrespectiveowners,andtheyarementionedforidentificationpurposesonly.
CopyrightNokiaSolutionsandNetworks2014/02/28.Allrightsreserved
ImportantNoticeonProductSafety
Thisproductmaypresentsafetyrisksduetolaser,electricity,heat,andothersourcesof
danger.
Only trained and qualified personnel may install, operate, maintain or otherwise handle
this product and only after having carefully read the safety information applicable to this
product.
ThesafetyinformationisprovidedintheSafetyInformationsectionintheLegal,Safety
andEnvironmentalInformationpartofthisdocumentordocumentationset.
NokiaSolutionsandNetworksiscontinuallystrivingtoreducetheadverseenvironmentaleffectsof
itsproductsandservices.Wewouldliketoencourageyouasourcustomersanduserstojoinusin
working towards a cleaner, safer environment. Please recycle product packaging and follow the
recommendationsforpoweruseandproperdisposalofourproductsandtheircomponents.
IfyoushouldhavequestionsregardingourEnvironmentalPolicyoranyoftheenvironmentalservicesweoffer,pleasecontactusatNokiaSolutionsandNetworksforanyadditionalinformation.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
TableofContents
Thisdocumenthas231pages
Summaryofchanges.................................................................. 10
Issue:2-9
Overview.......................................................................................11
AS7-CC105007........................................................................... 14
AS7-DC110791........................................................................... 17
CLAB-SC08839...........................................................................21
CLAB-UC111246......................................................................... 24
CLAB-UAC111464.......................................................................27
CL3TG-UC111247,CL2TG-UAC111461,CL3TG-VAC111463. 30
8
8.1
8.2
CL3TG-UAC111462.................................................................... 33
CL3TG-UA(version1)................................................................. 33
CL3TG-UA(version3)................................................................. 36
Tonegeneratorsandsequencingmemoryfilesizesettingsof
CL3TG-U/-V/-VA,CL3TG-UAversion3,CL2TG-U/-UA/-UT........39
10
10.1
10.1.1
10.2
10.2.1
10.3
CP1D-AC111441......................................................................... 41
AdvantechCP1D-A...................................................................... 41
EquippingDIMMmodules............................................................ 41
RadisysCP1D-A.......................................................................... 42
EquippingDIMMmodules............................................................ 43
DIP-switchsettings.......................................................................43
11
11.1
11.1.1
11.1.2
11.2
11.2.1
11.2.2
11.3
11.3.1
11.3.2
CP816-AC108488....................................................................... 46
AdvantechCP816-A.....................................................................46
EquippingDIMMmodules............................................................ 46
DIP-switchsettings.......................................................................47
ForceCP816-A............................................................................ 49
EquippingDIMMmodules............................................................ 49
DIP-switchsettings.......................................................................50
RadiSysCP816-A........................................................................ 52
EquippingDIMMmodules............................................................ 52
DIP-switchsettings.......................................................................53
12
12.1
12.1.1
12.1.2
12.2
CP816-ACC111134..................................................................... 55
AdvantechCP816-AC.................................................................. 55
EquippingDIMMmodules............................................................ 55
DIP-switchsettings.......................................................................56
RadiSysCP816-AC......................................................................58
DN70630644
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
12.2.1
12.2.2
EquippingDIMMmodules............................................................ 58
DIP-switchsettings.......................................................................59
13
ETIP1-AC111193.........................................................................61
14
14.1
14.2
ETPC111826............................................................................... 64
Jumpers....................................................................................... 64
DIP-switches................................................................................ 64
15
15.1
15.2
ETP-AC111828............................................................................67
Jumpers....................................................................................... 67
DIP-switches................................................................................ 67
16
ETS2C109474.............................................................................70
17
17.1
17.2
17.3
17.4
ET16C109519............................................................................. 73
EmersonET16(versions1-4)...................................................... 73
EmersonET16(version5onwards).............................................74
InterphaseET16...........................................................................75
Interchangeabilitysettings............................................................76
18
HWAT-AC08950.......................................................................... 77
19
HWAT-BC111250.........................................................................80
20
PCU2-DC108407........................................................................ 83
21
PCU2-EC110629.........................................................................87
22
SBMUX-AC110546......................................................................91
23
SERO-BC109453...................................................................... 111
24
SWPRO-CC111169................................................................... 116
25
SW256BC109365..................................................................... 120
26
TR3EC109454,TR3AC109455,TR3TC111545......................228
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
ListofFigures
Issue:2-9
Figure1
ConnectorsandmicroswitchesofAS7-C.......................................... 14
Figure2
ConnectorsandmicroswitchesofAS7-D.......................................... 17
Figure3
ConnectorsandmicroswitchesofAS7-D.......................................... 18
Figure4
JumpersandEPROMcircuitsofplug-inunitCLAB-S........................21
Figure5
Jumpersandflashcircuitsofplug-inunitCLAB-U............................. 24
Figure6
Jumpersandflashcircuitsofplug-inunitCLAB-UA...........................27
Figure7
Jumperpins,standardjumpersintheCL3TG-U,CL2TG-UA,CL3TGVA....................................................................................................... 30
Figure8
Jumperpins,standardjumpers,andEPROMcircuitsintheCL3TGUA(version1).....................................................................................33
Figure9
Jumperpins,standardjumpersintheCL3TG-UA(version3)............36
Figure10
MicroswitchesoftheCP1D-A(Advantech)....................................... 41
Figure11
MicroswitchesoftheCP1D-A(Radisys)............................................42
Figure12
ConnectorsandswitchesoftheCP816-A..........................................46
Figure13
ConnectorsandswitchesoftheCP816-A..........................................49
Figure14
ConnectorsandswitchesoftheCP816-A..........................................52
Figure15
ConnectorsandswitchesoftheCP816-AC....................................... 55
Figure16
ConnectorsandswitchesoftheCP816-AC....................................... 58
Figure17
DIPswitchesofplug-inunitETIP1-A..................................................61
Figure18
Jumpergroupoftheplug-inunitETP.................................................64
Figure19
Jumpergroupoftheplug-inunitETP-A............................................. 67
Figure20
JumpersandmicroswitchesoftheETS2.......................................... 70
Figure21
JumpersandmicroswitchesoftheEmersonET16(version1)......... 73
Figure22
JumpersandmicroswitchesoftheEmersonET16(version5
onwards).............................................................................................74
Figure23
JumpersandmicroswitchesoftheInterphaseET16.........................75
Figure24
Jumpersoftheplug-inunitHWAT-A...................................................77
Figure25
Jumpersoftheplug-inunitHWAT-B...................................................80
Figure26
Theconnectors,LEDindicatorsandDIPswitchgroupofthePCU2-D..
83
Figure27
Jumpers,DIPswitchandbackplaneconnectorsofplug-inunitPCU2E......................................................................................................... 87
Figure28
Connectors,microswitchandsettingsoftheSBMUX-A....................91
Figure29
JumperandmicroswitchsettingsoftheSERO-B............................ 111
Figure30
DIPswitchesoftheplug-inunitSWPRO-C...................................... 116
Figure31
Connectors,microswitchandsettingsoftheSW256B....................120
Figure32
Jumpergroupoftheplug-inunitTR3E/A......................................... 228
Figure33
Jumpergroupoftheplug-inunitTR3T(version1)...........................228
Figure34
Jumpergroupoftheplug-inunitTR3T(version2)...........................229
DN70630644
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
ListofTables
Table1
SW1switchsettings........................................................................... 14
Table2
Interchangeabilitycodesettings......................................................... 15
Table3
Switchsettings(SWA)........................................................................ 18
Table4
Interchangeabilitycodesettings......................................................... 19
Table5
StandardsettingsofCLAB-S(W1,W3,W4,W5-7,W9,W11,W12). 21
Table6
InterchangeabilitycodesettingsofCLAB-S(W13)............................ 22
Table7
StandardsettingsofCLAB-U(W51,W66,W70,W73,W74,W75,
W78,W79,W82,W86).......................................................................24
Table8
InterchangeabilitycodesettingsofCLAB-U(W73)............................ 25
Table9
StandardsettingsofCLAB-UA(W51,W66,W70,W73,W74,W75,
W82,W86)..........................................................................................27
Table10
InterchangeabilitycodesettingsofCLAB-UA(W73)..........................28
Table11
StandardsettingsofCL3TG-U,CL2TG-UA,CL3TG-VA.................... 31
Table12
InterchangeabilitycodesettingsofCL3TG-U,CL2TG-UA,CL3TG-VA
(W11).................................................................................................. 32
Table13
StandardsettingsofCL3TG-UA(version1).......................................34
Table14
AlternativesettingsofCL3TG-UA(version1)(W3,W4,W5,W6,W7)..
34
Table15
InterchangeabilitycodesettingsofCL3TG-UA(version1)(W13)......35
Table16
StandardsettingsofCL3TG-UA(version3).......................................37
Table17
InterchangeabilitycodesettingsofCL3TG-UA(W11)........................ 37
Table18
ToneandsequencingmemoryjumpersettingsofCL3TG-U/-V/-VA,
CL3TG-UAversion3andCL2TG-U/-UA/-UT.....................................39
Table19
SWA/SW1switchsettings.................................................................. 43
Table20
Interchangeabilitycode(ICC)settings(SWA/SW1)........................... 44
Table21
SW1switchsettings........................................................................... 47
Table22
Interchangeabilitycode(ICC)settings(SW1).................................... 48
Table23
SW1switchsettings........................................................................... 50
Table24
Interchangeabilitycode(ICC)settings(SW1).................................... 50
Table25
SW3switchsettings........................................................................... 53
Table26
Interchangeabilitycode(ICC)settings(SW3).................................... 53
Table27
SW1switchsettings........................................................................... 56
Table28
Interchangeabilitycode(ICC)settings(SW1).................................... 57
Table29
SW3switchsettings........................................................................... 59
Table30
Interchangeabilitycode(ICC)settings(SW3).................................... 59
Table31
StandardsettingsofETIP1-A(DIPswitchS2andS3).......................61
Table32
InterchangeabilitycodesettingsofETIP1-A(DIP-SwitchS1))...........62
Table33
StandardsettingsofW11................................................................... 64
Table34
InterchangeabilitycodesettingsofETP............................................. 65
Table35
InterchangeabilitycodesettingswithDIP-switchS1.......................... 65
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
Issue:2-9
Table36
StandardsettingsofW11................................................................... 67
Table37
InterchangeabilitycodesettingsofETP-A..........................................68
Table38
InterchangeabilitycodesettingswithDIP-switchS1.......................... 68
Table39
JumperW3settings............................................................................70
Table40
Interchangeabilitycode(ICC)settings(SW1).................................... 71
Table41
Configurationsettings(SW2)..............................................................71
Table42
Interchangeabilitycode(ICC)settings(B2/W2/W1)....................... 76
Table43
StandardsettingsofHWAT-A(W3,W10)...........................................77
Table44
AlternativesettingsofHWAT-A(W2)..................................................78
Table45
InterchangeabilitycodesettingsofHWAT-A(W4)..............................78
Table46
StandardsettingsofHWAT-B(W6).................................................... 80
Table47
AlternativesettingsofHWAT-B(W1)..................................................81
Table48
InterchangeabilitycodesettingsofHWAT-B(W4)..............................81
Table49
TheuseofW5.................................................................................... 84
Table50
TheuseofW6.................................................................................... 84
Table51
Settingtheinterchangeabilitycode.....................................................85
Table52
TheuseofW5forPCU2-DinBSC3i..................................................86
Table53
TheuseofW6forPCU2-DinBSC3i..................................................86
Table54
SettingsofPCU2-EinBSC3i660GSWB(W1)..................................87
Table55
SettingsofPCU2-EinBSC3i660GSW1KB(W1)............................. 88
Table56
SettingsofPCU2-EinBSC3i1000/2000(W1)...................................88
Table57
SettingsofPCU2-EinUpgratedFlexiBSC(W1)............................... 88
Table58
SettingsofPCU2-EinNewdeliveredFlexiBSC(W1)....................... 88
Table59
StandardsettingsofPCU2-EinFlexiBSC(W12)..............................89
Table60
StandardsettingsofPCU2-EinFlexiBSC(W13)..............................89
Table61
InterchangeabilitycodesettingsofPCU2-E(SW1)............................89
Table62
PCMmodesettingsontheSBMUX-A(SW1).....................................91
Table63
InterchangeabilitysettingsontheSBMUX-A(SW2).......................... 92
Table64
Interchangeabilitycode(ICC)settings(SW2).................................... 92
Table65
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).... 93
Table66
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).... 94
Table67
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).... 95
Table68
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).... 96
Table69
PCMmodesettingsontheSBMUX-A(SW1).....................................97
Table70
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).... 97
Table71
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).... 97
Table72
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).... 99
Table73
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).. 100
Table74
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).. 102
Table75
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).. 103
DN70630644
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
Table76
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).. 105
Table77
PCMmodesettingsontheSBMUX-A(SW1)...................................106
Table78
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).. 106
Table79
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).. 107
Table80
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).. 108
Table81
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).. 109
Table82
AlternativesettingofSERO-B...........................................................111
Table83
InterchangeabilitycodesettingsofSERO-B(W11).......................... 114
Table84
Switchsettings(SWA)...................................................................... 117
Table85
InterchangeabilitycodesettingsofSWPRO-C................................. 117
Table86
Switchsettings(SWE)...................................................................... 118
Table87
GSWBControlBusClockPhasecodesettings................................119
Table88
PCMmodesettingsontheSW256B(SW1).....................................120
Table89
InterchangeabilitysettingsontheSW256B(SW2)...........................121
Table90
Interchangeabilitycode(ICC)settings(SW2).................................. 121
Table91
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).... 122
Table92
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).... 123
Table93
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).... 124
Table94
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).... 125
Table95
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW1)..
126
Table96
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW3).
126
Table97
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW4)..
130
Table98
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW5)..
134
Table99
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW6)..
135
Table100
JumpersettingoftheSW256BincombinedBSC/TCSMinstallation
whereBSCpartisS15newdeliveryFlexiBSC(SW1).................... 144
Table101
JumpersettingoftheSW256BincombinedBSC/TCSMinstallation
whereBSCpartisS15newdeliveryFlexiBSC(SW3)................... 145
Table102
JumpersettingoftheSW256BincombinedBSC/TCSMinstallation
whereBSCpartisS15newdeliveryFlexiBSC(SW4).................... 148
Table103
JumpersettingoftheSW256BincombinedBSC/TCSMinstallation
whereBSCpartisS15newdeliveryFlexiBSC(SW5).................... 152
Table104
JumpersettingoftheSW256BincombinedBSC/TCSMinstallation
whereBSCpartisS15newdeliveryFlexiBSC(SW6).................... 153
Table105
PCMmodesettingsontheSW256B(SW1).....................................175
Table106
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).... 176
Table107
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).... 178
Table108
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).... 181
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCandTCSM3i
Issue:2-9
Table109
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).... 183
Table110
PCMmodesettingsontheSW256B(SW1).....................................187
Table111
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).... 187
Table112
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).... 189
Table113
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).... 193
Table114
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).... 195
Table115
PCMmodesettingsontheSW256B(SW1).....................................200
Table116
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).... 201
Table117
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).... 202
Table118
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).... 207
Table119
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).... 209
Table120
PCMmodesettingsontheSW256B(SW1).....................................213
Table121
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).... 214
Table122
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).... 216
Table123
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).... 221
Table124
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).... 223
Table125
InterchangeabilitycodesettingsofTR3E/A(W7)andTR3T(W12).......
229
Table126
ETSI/ANSIsettingsofTR3T(W14).................................................. 230
DN70630644
Summaryofchanges
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Summaryofchanges
Changesbetweendocumentissuesarecumulative.Therefore,thelatestdocument
issuecontainsallchangesmadetopreviousissues.
Changesbetweenissues2-9and2-8
W66jumpersettinginCLAB-UC111246andCLAB-UAC111464isupdated.
Changesbetweenissues2-8and2-7
SectionsCLAB-UC111246andCLAB-UAC111464havebeenadded.
Changesbetweenissues2-7and2-6
SectionPCU2-EC110629updatedwithjumpersettinginfo.
10
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Overview
1 Overview
Jumpersettingsofplug-inunitsinFlexiBSCandTCSM3iprovidesthebasicinformation
neededforsettingthevariousjumpersoftheplug-inunitsintheFlexiBSCandTCSM3i.
Thesettingsarereferredtoasstandardwhennochangesarerequired,andalternative
whentheapplicationdeliveredmayneedreconfiguration.
Beforesettingthevariousjumpersoftheplug-inunitsintheFlexiBSCandTCSM3i,the
userisadvisedtoreadtheinformationpresentedbelow.
Presentationofthesettings
Thestandardandalternativejumpersoftheplug-inunitsarepresentedintablesexcept
iftheplug-inunithasfactorysettings.Thestandardsettingsareillustratedinthejumper
grouplocationmaps.Forthestandardjumpers,thetableindicatesthejumpergroup
number,theconnectionrequiredandanoteabouttheconnection.Forthealternative
settings,themeaningoftheconnection(liketheplug-inunitlocation),therequired
connectionandanoteabouttheconnectionarelisted.Eachalternativejumpergroupis
precededbyatitledescribingit.
InthecolumnConnection,ahyphen(-)isusedbetweenthepinsofthejumpergroup
thataretobeconnectedontheplug-inunit.Thepinsaresymbolizedbyconsecutive
numbers.Ifthereisonlyahyphenandnonumbersinthecolumn,noconnectionis
made.Thenumbersofthejumpergroup(s)arealsogivenforthealternativesettings.
ThecolumnNoteindicatesthealternativeselectedwiththejumperconcerned.Ifthe
jumpergroupisrelevantonlyinconnectionwithplug-inunittesting,thecolumnisblank.
Thealternativesarelistedintheplug-inunitdescriptions.
Iftheplug-inunithasajumpergroupwhichisstrappedforinterchangeability,thesetting
alternativesarepresentedinaformthatdiffersfromthepresentationoftheothertables.
Intheinterchangeabilitytable,
X=thecorrespondingconnectionismade
blank=thecorrespondingconnectionisnotmade.
Implementationofthejumpersettings
Ahardwaresetting(strapping)ismadebymeansofajumper(markedbyarectangle).
Thematerialsrequired:Jumpercode1529100089
Selectionofsettings
Settingsareoftencalledonlyjumpersettings,orwhentheycanclearlybedefinedthey
aredividedintotwogroups:
Issue:2-9
standardsettings
alternativesettings
DN70630644
11
Overview
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Thestandardsettingsdonotdependonexternalfactors,sotheyarealwayssetinthe
samewayregardlessoftheequipmentposition.
Thealternativesettingsdependonexternalfactors,suchasthetrackposition,the
parametertobeselected,andtheoperatingenvironment.
Theplug-inunitswithbothstandardandalternativesettingsareamixtureofthecasesin
thetwopreviouschapters.
Presentationoftheread-onlymemorycircuits
Thefollowinginformationisgivenabouttheread-onlymemorycircuits:
locationofread-onlymemorycircuit(s)oftheplug-inunit
installationdirectionofread-onlymemorycircuit(s)(directionofthenotchofcircuit(s))
settingofread-onlymemorycircuit(s)inthesocket(socketsofcircuit(s)areindicated
withbrokenline)
thefollowingcanbereadinsidethecircuit(s)dependingonthecase:
EPROMorPROM;eithermarkingHIGHorLOWon8-bitread-onlymemory
circuits(noton16-bitcircuits)
baseaddressesofcircuits(forsomeplug-inunits,onlythebeginningofthebase
addressofthecircuit,e.g.60=60000H,A0=A0000H,ispresented)orthename
oftheprogramonthecircuit+indexesofcircuits.
Thefollowingplug-inunitshavesettingsthattheusercanset:
AS7-C
AS7-D
CLAB-S
CL3TG-U,CL2TG-UA,CL3TG-VA
CL3TG-UA
CP1D-A
CP816-A
CP816-AC
ETIP1-A
ETP
ETP-A
ETS2
ET16
HWAT-A
12
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Overview
HWAT-B
PCU2-D
PCU2-E
SBMUX-A
SERO-B
SWPRO-C
SW256B
TR3E,TR3A,TR3T
Thefollowingplug-inunitshavenojumpersettingstobesetbytheuser:
Issue:2-9
DCAR1-A
ESB24-A,ESB24-DandESB26:Theswitchandthepinheaderontheboardare
onlyfortestingpurposes.
PSC6-ABandPSC6-A
PSC6-CBandPSC6-C
PSC6-D
DN70630644
13
AS7-CC105007
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
2 AS7-CC105007
ThefiguresbelowshowstheAS7-Clayoutwithlocationofswitchblockandconnectors.
AS7-Clayout
Figure1
ConnectorsandmicroswitchesofAS7-C
SW1
P5
P4
SW1
OFF ON
P1
1
2
3
4
5
6
12
11
10
9
8
7
DN03309124
Interchangeabilitycodesettings
TheInterchangeabilitySwitchBlockconsistsofa6positionDIPswitch.Thisswitch
containsthefourinterchangeabilitycodebits.Theinterchangeabilitylinesdriveto'0'
whentheswitchesareOFF.
'OFF'isGND,'ON'isVCC.
Table1
14
SW1switchsettings.
Switch1
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3(MSB)
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0(LSB)
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table1
AS7-CC105007
SW1switchsettings.(Cont.)
Switch1
Setting
Meaning
5-8
OFF
Notinuse
6-7
OFF
Notinuse.
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table2
Interchangeabilitycodesettings
ICCcode
Meaning
SW1:112
(MSB)
SW1:211
SW1:310
SW1:49(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
Issue:2-9
DN70630644
15
AS7-CC105007
Table2
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Interchangeabilitycodesettings(Cont.)
ICCcode
Meaning
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
16
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
AS7-DC110791
3 AS7-DC110791
TheAS7-Dhastwovendorsthatdifferinlayoutbutareidenticalinfunction.
AdvantechAS7-D
Figure2
ConnectorsandmicroswitchesofAS7-D
Interchangeability
SWA
P5
OFFON
ON
P4
2 3 4
SWB
1
1
2
3
4
8
7
6
5
SWA
Bootsource
P3
SWB
OFFON
ON
2 3 4
1
2
3
4
P2
8
7
6
5
P1
DN70542436
Issue:2-9
Thereareotherpinheadersontheboardwhicharenotpresentedinthefigure.
OnlytheDIPswitcheswhichcanbesetbytheuseraredescribedhere.Donot
makeanychangestootherDIPswitchesorpinheaders.OtherDIPswitches
areusedforproduction,debuggingandtestingpurposesonly.
DN70630644
17
AS7-DC110791
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
RadiSysAS7-D
Figure3
ConnectorsandmicroswitchesofAS7-D
SWA
P5
P4
P3
Interchangeability
SWA
P2
ON
1
2 3 4
P1
OFFON
1
2
3
4
8
7
6
5
DN70542596
Interchangeabilitycodesettings
TheInterchangeabilitySwitchBlock(SWA)consistsofa4positionDIPswitch.This
switchcontainsthefourinterchangeabilitycodebits.Theinterchangeabilitylinesdriveto
'0'whentheswitchesareOFF.
'OFF'isGND,'ON'isVCC.
Table3
Switchsettings(SWA)
Switch
DefaultSetting
Meaning
1-8
OFF*)
Interchangeabilitycodebit3(MSB)
2-7
OFF*)
Interchangeabilitycodebit2
3-6
OFF*)
Interchangeabilitycodebit1
4-5
OFF*)
Interchangeabilitycodebit0(LSB)
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
18
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table4
AS7-DC110791
Interchangeabilitycodesettings
ICCcode
Setting
SW18(MSB)
SW27
SW36
SW45(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Bootsourceselection
Thebootsourceselectionswitchblock(SWB)consistsofa4-positionDIPswitch.Itis
onlypresentintheAdvantechvariantofAS7-D.
Issue:2-9
Switch
DefaultSetting Meaning
1-8
OFF
Notinuse.
DN70630644
19
AS7-DC110791
20
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Switch
DefaultSetting Meaning
2-7
OFF
Notinuse.
3-6
OFF
Notinuse.
4-5
ON
Bootmode.Defaultsetting.Donotchangethis
setting.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CLAB-SC08839
4 CLAB-SC08839
Figure4
JumpersandEPROMcircuitsofplug-inunitCLAB-S
Standard settings
W3-W4
W11
5
6
7
8
3
2
1
W1
W1,W7, W5-W6,
W10
W9,W12
W3 W4
PRTA
W5
W6
W9
W7
4
3
2
1
1
1
W11
W10
PROM
E0000H
W12
Interchangeability
W13
8765
PROM
C0000H
W13
1234
DN98618661
ThePRTA(ProcessorTestAdaptor)isaconnectorwhichcanbeusedfortestingand
servicing.
Standardsettingsarepresentedinthetablebelow,andthejumpersmustbesetas
shownduringnormaloperation.
Therearenoalternativesettingsavailableontheplug-inunit.
JumpergroupW13isusedforsettingtheinterchangeabilitycodeoftheplug-inunit
whenrequired,seethetablebelow.
Standardsettings(W1,W3,W4,W5-7,W9,W11,W12)
Table5
StandardsettingsofCLAB-S(W1,W3,W4,W5-7,W9,W11,W12)
Jumper
Setting
Meaning
W1;1-2
ON
32MHzclocksignaloftheprocessorisnotdisconnected
W3;2-3
ON
Automaticphaseadvanceenabled(usedinMobileCircuit
CoreDXNEs)
W4;2-3
ON
W12;1-2
ON
W5;1-2
ON
Issue:2-9
Watchdogenabled
DN70630644
21
CLAB-SC08839
Table5
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
StandardsettingsofCLAB-S(W1,W3,W4,W5-7,W9,W11,W12)(Cont.)
Jumper
Setting
Meaning
W6;1-2
ON
The32MHzoutputsignalofthephaselockcircuitisnotdisconnected
W7;1-2
ON
Theresetsignaloftheplug-inunitisnotdisconnected
W9;1-2
ON
The64MHzoutputsignalofthephaselockcircuitisnotdisconnected
W10;1-2
ON
Theresetsignaloftheprocessorisnotdisconnected
W11;ALL
OFF
Usedfortestingofthephaselockcircuit
Interchangeabilitycodesettings(W13)
Table6
InterchangeabilitycodesettingsofCLAB-S(W13)
ICCcode
W13settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
22
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table6
CLAB-SC08839
InterchangeabilitycodesettingsofCLAB-S(W13)(Cont.)
ICCcode
W13settings
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
Issue:2-9
DN70630644
23
CLAB-UC111246
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
5 CLAB-UC111246
Figure5
Jumpersandflashcircuitsofplug-inunitCLAB-U
Standardsettings
W51
W51 W66
4
6 5
2 1
3 4
W66
PRTA
W71,72
W71
W73
4 3
4 3
1
2
W70 W72
W78 W79
W82
W70,74,
75,78,86 W79 W82
W75
W74
3
2
4
5
6
W86
4
3
1 2
Interchangeability
PROM
8765
W73
1234
Dn70550007
ThePRTA(ProcessorTestAdaptor)isaconnectorwhichcanbeusedfortestingand
servicing.
Standardsettingsarepresentedinthetablebelow,andthejumpersmustbesetas
shownduringnormaloperation.
Therearenoalternativesettingsavailableontheplug-inunit.
JumpergroupW73isusedforsettingtheinterchangeabilitycodeoftheplug-inunit
whenrequired,seethetablebelow.
Standardsettings(W51,W66,W70,W74,W75,W78,W79,W82,W86)
Table7
StandardsettingsofCLAB-U(W51,W66,W70,W73,W74,W75,W78,
W79,W82,W86)
Jumper
Setting
Meaning
W51;1-4
ON
Theresetsignaloftheplug-inunitisdisconnected
W66;4-5
ON
Usedfortestingofthephaselockcircuit
W70;1-4
ON
WatchdogStopisenabled
24
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table7
CLAB-UC111246
StandardsettingsofCLAB-U(W51,W66,W70,W73,W74,W75,W78,
W79,W82,W86)(Cont.)
Jumper
Setting
Meaning
W71;1-2
OFF
Settingofphaseadvance:LD2orTSR0Aautomaticsettingof
phaseadvance
W71;2-3
ON
W72;1-2
OFF
W72;2-3
ON
W74;1-4
ON
The32MHzoutputsignalofthephaselockcircuitisconnected
W75;1-4
ON
The64MHzoutputsignalofthephaselockcircuitisconnected
W78;1-4
ON
Automaticsettingofphaseadvance
W79;1-4
OFF
Flashiswriteprotected
W82;1-4
ON
Theprocessorisnotintheresetstate
W86;1-4
ON
32MHzclocksignaloftheprocessorisconnected
Settingofphaseadvance:LD4orTSR0Bautomaticsettingof
phaseadvance
Interchangeabilitycodesettings(W73)
Table8
InterchangeabilitycodesettingsofCLAB-U(W73)
ICCcode
W73settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
Issue:2-9
DN70630644
25
CLAB-UC111246
Table8
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
InterchangeabilitycodesettingsofCLAB-U(W73)(Cont.)
ICCcode
W73settings
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
26
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CLAB-UAC111464
6 CLAB-UAC111464
Figure6
Jumpersandflashcircuitsofplug-inunitCLAB-UA
Standardsettings
W51
W51
W66
8 7
6 5
2 1
1 2
3 4
W66
PRTA
W82
W86
3
2
1
4 3
W73
4
3
1
2
W75
W74
4
5
6
W70,74,
75,78,86
W82
W71
W71,72
W70 W72
W78
1 2
Interchangeability
PROM
8765
W73
1234
DN70616379?
ThePRTA(ProcessorTestAdaptor)isaconnectorwhichcanbeusedfortestingand
servicing.
Standardsettingsarepresentedinthetablebelow,andthejumpersmustbesetas
shownduringnormaloperation.
Therearenoalternativesettingsavailableontheplug-inunit.
JumpergroupW73isusedforsettingtheinterchangeabilitycodeoftheplug-inunit
whenrequired,seethetablebelow.
Standardsettings(W51,W66,W70,W74,W75,W82,W86)
Table9
StandardsettingsofCLAB-UA(W51,W66,W70,W73,W74,W75,W82,
W86)
Jumper
Setting
Meaning
W51;1-4
ON
Theresetsignaloftheplug-inunitisdisconnected
W66;4-5
ON
Usedfortestingofthephaselockcircuit
W70;1-4
OFF
Flashiswriteprotected
Issue:2-9
DN70630644
27
CLAB-UAC111464
Table9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
StandardsettingsofCLAB-UA(W51,W66,W70,W73,W74,W75,W82,
W86)(Cont.)
Jumper
Setting
Meaning
W71;1-2
OFF
Settingofphaseadvance:LD2orTSR0Aautomaticsettingof
phaseadvance
W71;2-3
ON
W72;1-2
OFF
W72;2-3
ON
W74;1-4
ON
The32MHzoutputsignalofthephaselockcircuitisconnected
W75;1-4
ON
The64MHzoutputsignalofthephaselockcircuitisconnected
W82;1-4
ON
Theprocessorisnotintheresetstate
W86;1-4
ON
32MHzclocksignaloftheprocessorisconnected
Settingofphaseadvance:LD4orTSR0Bautomaticsettingof
phaseadvance
Interchangeabilitycodesettings(W73)
Table10
InterchangeabilitycodesettingsofCLAB-UA(W73)
ICCcode
W73settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
28
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table10
CLAB-UAC111464
InterchangeabilitycodesettingsofCLAB-UA(W73)(Cont.)
ICCcode
W73settings
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
Issue:2-9
DN70630644
29
CL3TG-UC111247,CL2TG-UAC111461,CL3TG-VA
C111463
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
7 CL3TG-UC111247,CL2TG-UAC111461,
CL3TG-VAC111463
Figure7
Jumperpins,standardjumpersintheCL3TG-U,CL2TG-UA,CL3TG-VA
W1,
W6,
W8
W1
1
4
EPROM
A
EPROM
B
W5
W35
W39 W37
W2
W38
W9
W11
W5
W36
W40
W6
W11
W10
W8 W9
W10
W12
3
4
W12
5
3
W38
W2
W35
1
W40
4
W39
W36
W37
DN0967332
Standardsettingsarepresentedinthetablebelow,andthejumpersmustbesetas
shownduringnormaloperation.
AlternativesettingsonjumpergroupsW10,andW2dependontheapplicationas
presentedinthetablebelow.Inthepreviousdesign(CL3TG,CL3TG-S,CL2TG-S)the
capacityofsequentialmemorywasdeterminedbystrappinggroupsW4andW5andthe
capacityoftonememorywithstrappinggroupsW6andW7.Intheredesignonesizeof
memorywillbeusedforbothoptions,sothesestrapsarenotneededanymore.For
jumperW4andW5schematicwillbechangedtodoafixedconnectionequivalenttothe
shortbetweenpins1and2andforW6andW7theequivalentfixedconnectionis
betweenpins2and3.JumpergroupsW35,W36,W38,W39andW40areusedin
TONEFLASHandformoreinformation,pleaserefertoTonegeneratorsandsequencing
memoryfilesizesettingsofCL3TG-U/-V/-VA,CL3TG-UAversion3,CL2TG-U/-UA.
JumpergroupW11isusedforsettingtheinterchangeabilitycodeoftheplug-inunitwhen
required,seethetablebelow.
30
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CL3TG-UC111247,CL2TG-UAC111461,CL3TG-VA
C111463
Standardsettings(W1,W2,W6,W8,W10)
Table11
StandardsettingsofCL3TG-U,CL2TG-UA,CL3TG-VA
Jumper
Setting
Meaning
W1
1-2
ON=fortestinguseinnormaloperation
W2
1-2
ON=Tonegeneratoruses30timeslots
(usedwithTON-FIA-A)
OFF=Tonegeneratoruses28timeslots
(usedwithTON-SXCA)
W5
1-2
OFF=manualresetsignaloftheplug-in
unitdisconnectedinnormaloperation
W6
1-2
ON=normalsituation
OFF=poweronresettoCPLDdisconnected
W8
1-2
ON=normalsituation
OFF=16MHzclockoutputdisconnected
W9
2-3
ON=fortestinguseinnormaloperation
W10
1-2
ON=normalsituation
OFF=32MHzclockoutputdisconnected
W12
1-8
ON=Watchdogfunctionenabledinnormal
situation
OFF=Watchdogfunctiondisabled
2-7
ON=Flashwriteprotectionenabled
OFF=Flashwriteprotectiondisabled
W37
Issue:2-9
1-2
ON=fortestinguseinnormaloperation
DN70630644
31
CL3TG-UC111247,CL2TG-UAC111461,CL3TG-VA
C111463
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Interchangeabilitycodesettings(W11)
Table12
32
InterchangeabilitycodesettingsofCL3TG-U,CL2TG-UA,CL3TG-VA
(W11)
ICCcode
W11settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CL3TG-UAC111462
8 CL3TG-UAC111462
CL3TG-UAhastwodifferentversionswhichcanbeseparatedbydifferencesinthe
PWB.
8.1 CL3TG-UA(version1)
Figure8
Jumperpins,standardjumpers,andEPROMcircuitsintheCL3TG-UA
(version1)
W1
Alternative
settings
W2
W3 W4-W7
1
W6
1
2
3
PhasememoryB**)
W13
32 1
30 2
W5
W4
W7
32
30
W3
8765
J1
1
2
Phasememory A**)
1234
J5
W8
W9
PRTA
W11
Standard
settings
W1,W8
W11
123
W12
W13
PROM
90000H
DN98618697
J2
W2,W9,W12
1
Standardsettingsarepresentedinthetablebelow,andthejumpersmustbesetas
shownduringnormaloperation.
AlternativesettingsonjumpergroupsW3,W4,W5,W6,andW7dependonthe
applicationaspresentedinthetablebelow.
JumpergroupW13isusedforsettingtheinterchangeabilitycodeoftheplug-inunit
whenrequired,seethetablebelow.
Issue:2-9
Therearetwodifferentsizesofread-onlymemorycircuitsforphasememoryand
tonegeneratormemory:28-pin(256kbit)and32-pin(1Mbit/2Mbit/4Mbit).
ThePRTA(ProcessorTestAdaptor)W10isaconnectorwhichcanbeusedfor
testingandservicing.
DN70630644
33
CL3TG-UAC111462
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Standardsettings(W1,W2,W8,W9,W11,W12)
Table13
StandardsettingsofCL3TG-UA(version1)
Jumper
Setting
Meaning
W1;1-2
ON
Fortestingpurposes
W2;1-2
ON
Fortestingpurposes
W8;1-2
ON
Fortestingpurposes
W9;1-2
ON
Fortestingpurposes
W11;1-2
ON
Fortestingpurposes
W12;1-2
ON
Fortestingpurposes
Alternativesettings(W3,W4,W5,W6,W7)
Table14
AlternativesettingsofCL3TG-UA(version1)(W3,W4,W5,W6,W7)
Jumper
Setting
Meaning
W3;1-2
ON
TON-XXXproduct:
W4;2-3
ON
Tonegeneratormemory1Mbit/
W5;1-2
ON
Phasememory1Mbit
W6;1-2
ON
TON-MYAICCB
W7;2-3
ON
TON-SEAICCC
TON-SEBICCB
TON-GBAICCB
TON-GBBICCA
TON-LKAICCB
TON-THAICCB
TON-THBICCB
34
W3;1-2
ON
Tonegeneratormemory2Mbit
W4;2-3
ON
or4Mbit/Phasememory1Mbit
W5;1-2
ON
OtherTONproductsandnewer
W6;2-3
ON
ICCsthanlistedabove
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table14
CL3TG-UAC111462
AlternativesettingsofCL3TG-UA(version1)(W3,W4,W5,W6,W7)
(Cont.)
Jumper
Setting
Meaning
W7;2-3
ON
ICC=Interchangeabilitycode
Interchangeabilitycodesettings(W13)
Table15
Issue:2-9
InterchangeabilitycodesettingsofCL3TG-UA(version1)(W13)
ICCcode
W13settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
DN70630644
35
CL3TG-UAC111462
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table15
InterchangeabilitycodesettingsofCL3TG-UA(version1)(W13)(Cont.)
ICCcode
W13settings
ON
OFF
OFF
OFF
8.2 CL3TG-UA(version3)
CL3TG-UA(version3)jumpersettings
Figure9
Jumperpins,standardjumpersintheCL3TG-UA(version3)
W1,
W6,
W8
W1
1
4
EPROM
A
EPROM
B
W5
W35
W39 W37
W2
W38
W9
W11
W5
W36
W40
W6
W11
W10
W8 W9
W10
W12
3
4
W12
5
3
W38
W2
W35
1
W40
4
W39
W36
W37
DN0967332
JumpergroupsW35,W36,W38,W39andW40areusedinTONEFLASHandformore
information,pleaserefertoTonegeneratorsandsequencingmemoryfilesizesettingsof
CL3TG-U/-V/-VA,CL3TG-UAversion3,CL2TG-U/-UA/-UT.
ThesettingsforjumpersW1,W2,W5,W6,W8,W9,W10,W12andW37aredescribed
inthefollowingtable.
36
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CL3TG-UAC111462
StandardsettingforCL3TG-UA(version3)
Table16
StandardsettingsofCL3TG-UA(version3)
Jumper
Setting
Meaning
W1
1-2
ON=fortestinguseinnormaloperation
W2
1-2
ON=Tonegeneratoruses30timeslots
(usedwithTON-FIA-A)
OFF=Tonegeneratoruses28timeslots
(usedwithTON-SXCA)
W5
1-2
OFF=manualresetsignaloftheplug-in
unitdisconnectedinnormaloperation
W6
1-2
ON=normalsituation
OFF=poweronresettoCPLDdisconnected
W8
1-2
ON=normalsituation
OFF=16MHzclockoutputdisconnected
W9
2-3
ON=fortestinguseinnormaloperation
W10
1-2
ON=normalsituation
OFF=32MHzclockoutputdisconnected
W12
1-8
ON=Watchdogfunctionenabledinnormal
situation
OFF=Watchdogfunctiondisabled
2-7
ON=Flashwriteprotectionenabled
OFF=Flashwriteprotectiondisabled
W37
1-2
ON=fortestinguseinnormaloperation
Interchangeabilitycodesettings(W11)
Table17
InterchangeabilitycodesettingsofCL3TG-UA(W11)
ICCcode
W11settings
1-8
Issue:2-9
2-7
DN70630644
3-6
4-5
37
CL3TG-UAC111462
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table17
38
InterchangeabilitycodesettingsofCL3TG-UA(W11)(Cont.)
ICCcode
W11settings
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Tonegeneratorsandsequencingmemoryfilesize
settingsofCL3TG-U/-V/-VA,CL3TG-UAversion3,
CL2TG-U/-UA/-UT
9 Tonegeneratorsandsequencingmemoryfile
sizesettingsofCL3TG-U/-V/-VA,CL3TG-UA
version3,CL2TG-U/-UA/-UT
TwotoneproductsTON-FIA-AandTON-SXCAareusedbutothertoneproductsarealso
possible.
Thetableinthefollowingdescribesthetoneandsequencingmemoryjumpersettingsfor
allnewCLxTG-XvariantsincludingCL3TG-U/-V/-VA,CL3TG-UAversion3andCL2TGU/-UA/-UT.
Table18
ToneandsequencingmemoryjumpersettingsofCL3TG-U/-V/-VA,CL3TGUAversion3andCL2TG-U/-UA/-UT
FileSize
Tone
Memory(A)
ToneProduct Sequencing
Memory(B)
32kByte
IC58
IC57
W392-3
W352-5
W394-5
W381-2-3
ToneProduct
TON-SXCA
W384-5
W401-4
128kByte
W364-5
TON-SXCA
W355-6
W392-3
W382-3
W394-5
W384-5
TON-FIA-A
W401-2
256kByte
W362-3
TON-FIA-A
W351-2
W364-5
W355-6
W391-2
W381-2
W394-5
W384-5
W401-2
512kByte
Issue:2-9
W362-3
W351-2
W364-5
W355-6
W391-2
W381-2
W395-6
W385-6
DN70630644
39
Tonegeneratorsandsequencingmemoryfilesize
settingsofCL3TG-U/-V/-VA,CL3TG-UAversion3,
CL2TG-U/-UA/-UT
Table18
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
ToneandsequencingmemoryjumpersettingsofCL3TG-U/-V/-VA,CL3TGUAversion3andCL2TG-U/-UA/-UT(Cont.)
FileSize
Tone
Memory(A)
ToneProduct Sequencing
Memory(B)
IC58
ToneProduct
IC57
W401-2
40
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP1D-AC111441
10 CP1D-AC111441
TheCP1D-Ahastwovendorsthatdifferinlayoutbutareidenticalinfunction.Theycan
bedistinguishedfromeachotherbythefollowing:
slightdifferencesinthefrontpanel(coolingfins)
differencesonthePWB.
10.1 AdvantechCP1D-A
Figure10
MicroswitchesoftheCP1D-A(Advantech)
P5
1
SWA
P4
P2
2
11 01 10 00
P1
DN70658197
1
2
3
4
5
6
ON
ON
SWA
OFF
1 2 3 4 5 6
Interchangeability
12
11
10
9
8
7
10.1.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstDIMM10andDIMM00andDIMM11andDIMM01
second.
Issue:2-9
DN70630644
41
CP1D-AC111441
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
WhenusingDualChannelMode,parallelDIMMslots(i.e.DIMM10and
DIMM00,forexample)musthaveidenticalDIMMs(anidenticalDIMMmeans
anidenticalNokiaSiemensNetworksC-code).DIMMsinserieswithina
memorychanneldonothavetobeidentical(i.e.DIMM11andDIMM10,for
example).Forexample,therecanbe512MBDIMMsinslotsDIMM11and
DIMM01and1GBDIMMsinslotsDIMM10andDIMM00.
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstDIMM00andDIMM01
second.
DualChannelModeisdefault.SingleChannelModeisusedonlyifsospecified
indeliveryspecificdocumentation.
10.2 RadisysCP1D-A
Figure11
MicroswitchesoftheCP1D-A(Radisys)
SW1
P5
P4
P2
2
P1
42
DN70630644
OFF
ON
ON
SW1
1
2
3
4
5
6
1 2 3 4 5 6
Interchangeability
12
11
10
9
8
7
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP1D-AC111441
10.2.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstJ14andJ13andJ12andJ11second.
WhenusingDualChannelMode,parallelDIMMslots(i.e.J14andJ13,for
example)musthaveidenticalDIMMs(anidenticalDIMMmeansanidentical
NokiaSiemensNetworksC-code).DIMMsinserieswithinamemorychannel
donothavetobeidentical(i.e.J14andJ12,forexample).Forexample,there
canbe512MBDIMMsinslotsJ14andJ13and1GBDIMMsinslotsJ12and
J11.
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstJ14andJ12second.
DualChannelModeisdefault.SingleChannelModeisusedonlyifsospecified
indeliveryspecificdocumentation.
10.3 DIP-switchsettings
Thefollowingsettingsaremadewithmicroswitchseethetablebelow:
Interchangeabilitycode
MBIFstatus(inuse/notinuse).
Table19
SWA/SW1switchsettings.
Switch
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0
5-8
OFF
Notinuse
6-7
OFF
MessageBusInterface(MBIF)status:
OFF=MBIFinuse(bitD3inregister104hreads
0)
Issue:2-9
DN70630644
43
CP1D-AC111441
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table19
SWA/SW1switchsettings.(Cont.)
Switch
Setting
Meaning
ON=MBIFisnotinuse(bitD3inregister6Eh
readsas0)
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table20
Interchangeabilitycode(ICC)settings(SWA/SW1).
ICCcode
Switchsetting
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
44
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table20
Interchangeabilitycode(ICC)settings(SWA/SW1).(Cont.)
ICCcode
Switchsetting
ON
Issue:2-9
CP1D-AC111441
ON
ON
DN70630644
OFF
45
CP816-AC108488
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
11 CP816-AC108488
TheCP816-Ahasthreevendorsthatdifferinlayoutbutareidenticalinfunction.They
canbedistinguishedfromeachotherbythefollowing:
slightdifferencesinthefrontpanel(coolingfins)
differencesonthePWB.
11.1 AdvantechCP816-A
Figure12
ConnectorsandswitchesoftheCP816-A
P5
SW1
P4
P3
P2
A1
P1
B1 A2 B2
DN05160554
Interchangeability
SW1
OFFON
1
12
2
11
3
10
4
9
5
8
6
7
11.1.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstA2andB2andA1andB1second.
46
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP816-AC108488
WhenusingDualChannelMode,parallelDIMMslots(i.e.A2andB2,for
example)musthaveidenticalDIMMs(anidenticalDIMMmeansanidentical
NokiaSiemensNetworksC-code).DIMMsinserieswithinamemorychannel
donothavetobeidentical(i.e.A1andA2,forexample).Forexample,there
canbe512MBDIMMsinslotsA1andB1and1GBDIMMsinslotsA2andB2.
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstA2andA1second.
DualChannelModeisdefault.SingleChannelModeisusedonlyifsospecified
indeliveryspecificdocumentation.
11.1.2 DIP-switchsettings
Thefollowingsettingsaremadewithmicroswitchseethetablebelow:
Interchangeabilitycode
MBIFstatus(inuse/notinuse).
Table21
SW1switchsettings.
Switch1
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0
5-8
OFF
Notinuse
6-7
OFF
MessageBusInterface(MBIF)status:OFF=
MBIFinuse(bitD3inregister104hreads0).
InNEinstallations,whenEMBisused,thissetting
mustbeON=MBIFnotinuse.
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Issue:2-9
DN70630644
47
CP816-AC108488
Table22
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Interchangeabilitycode(ICC)settings(SW1).
ICCcode
Switchsetting
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
48
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP816-AC108488
11.2 ForceCP816-A
Figure13
ConnectorsandswitchesoftheCP816-A
SW1
MCH
ICH3-S
CPU
P10P12P11 P13
DN0480066
SW1
ON
7
8
9
10
11
12
OFF
6
5
4
3
2
1
11.2.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstP13andP11andP12andP10second.
Issue:2-9
WhenusingDualChannelMode,parallelDIMMslots(i.e.P13andP11,for
example)musthaveidenticalDIMMs(anidenticalDIMMmeansanidentical
NokiaSiemensNetworksC-code).DIMMsinserieswithinamemorychannel
donothavetobeidentical(i.e.P13andP12,forexample).Forexample,there
canbe512MBDIMMsinslotsP13andP11and1GBDIMMsinslotsP12and
P10.
DN70630644
49
CP816-AC108488
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstP11andP10second
DualChannelModeisdefault.TheSingleChannelModeisusedonlyifso
specifiedindeliveryspecificdocumentation.
11.2.2 DIP-switchsettings
Thefollowingsettingsaremadewithmicroswitchseethetablebelow:
Interchangeabilitycode
MBIFstatus(inuse/notinuse).
Table23
SW1switchsettings.
Switch1
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0
5-8
OFF
Notinuse
6-7
OFF
MessageBusInterface(MBIF)status:OFF=
MBIFinuse(bitD3inregister104hreads0).
InNEinstallations,whenEMBisused,thissetting
mustbeON=MBIFnotinuse.
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table24
Interchangeabilitycode(ICC)settings(SW1).
ICCcode
Switchsetting
50
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table24
CP816-AC108488
Interchangeabilitycode(ICC)settings(SW1).(Cont.)
ICCcode
Switchsetting
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Issue:2-9
DN70630644
51
CP816-AC108488
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
11.3 RadiSysCP816-A
Figure14
ConnectorsandswitchesoftheCP816-A
ICH3-S
Daughter
Board
MCH
CPU
SW3
SW3
DN0480078
OFF
1
2
3
4
5
6
ON
12
11
10
9
8
7
11.3.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstJ14andJ13andJ12andJ11second.
52
WhenusingDualChannelMode,parallelDIMMslots(i.e.J14andJ13,for
example)musthaveidenticalDIMMs(anidenticalDIMMmeansanidentical
NokiaSiemensNetworksC-code).DIMMsinserieswithinamemorychannel
donothavetobeidentical(i.e.J14andJ12,forexample).Forexample,there
canbe512MBDIMMsinslotsJ14andJ13and1GBDIMMsinslotsJ12and
J11.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP816-AC108488
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstJ14andJ12second.
DualChannelModeisdefault.SingleChannelModeisusedonlyifsospecified
indeliveryspecificdocumentation.
11.3.2 DIP-switchsettings
Thefollowingsettingsaremadewithmicroswitchseethetablebelow:
Interchangeabilitycode
MBIFstatus(inuse/notinuse).
Table25
SW3switchsettings.
Switch1
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0
5-8
OFF
Notinuse
6-7
OFF
MessageBusInterface(MBIF)status:OFF=
MBIFinuse(bitD3inregister104hreads0).
InNEinstallations,whenEMBisused,thissetting
mustbeON=MBIFnotinuse.
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table26
Interchangeabilitycode(ICC)settings(SW3).
ICCcode
Switchsetting
Issue:2-9
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
DN70630644
53
CP816-AC108488
Table26
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Interchangeabilitycode(ICC)settings(SW3).(Cont.)
ICCcode
Switchsetting
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
54
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP816-ACC111134
12 CP816-ACC111134
TheCP816-AChastwovendorsthatdifferinlayoutbutareidenticalinfunction.They
canbedistinguishedfromeachotherbythefollowing:
slightdifferencesinthefrontpanel(coolingfins)
differencesonthePWB.
12.1 AdvantechCP816-AC
Figure15
ConnectorsandswitchesoftheCP816-AC
P5
SW1
P4
P2
A1
P1
B1 A2 B2
DN70407181
Interchangeability
SW1
OFFON
1
12
2
11
3
10
4
9
5
8
6
7
12.1.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstA2andB2andA1andB1second.
Issue:2-9
DN70630644
55
CP816-ACC111134
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
WhenusingDualChannelMode,parallelDIMMslots(i.e.A2andB2,for
example)musthaveidenticalDIMMs(anidenticalDIMMmeansanidentical
NokiaSiemensNetworksC-code).DIMMsinserieswithinamemorychannel
donothavetobeidentical(i.e.A1andA2,forexample).Forexample,there
canbe512MBDIMMsinslotsA1andB1and1GBDIMMsinslotsA2andB2.
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstA2andA1second.
DualChannelModeisdefault.SingleChannelModeisusedonlyifsospecified
indeliveryspecificdocumentation.
12.1.2 DIP-switchsettings
Thefollowingsettingsaremadewithmicroswitchseethetablebelow:
Interchangeabilitycode
MBIFstatus(inuse/notinuse).
Table27
SW1switchsettings.
Switch1
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0
5-8
OFF
Notinuse
6-7
OFF
MessageBusInterface(MBIF)status:OFF=
MBIFinuse(bitD3inregister104hreads0).
InNEinstallations,whenEMBisused,thissetting
mustbeON=MBIFnotinuse.
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
56
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table28
CP816-ACC111134
Interchangeabilitycode(ICC)settings(SW1).
ICCcode
Switchsetting
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Issue:2-9
DN70630644
57
CP816-ACC111134
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
12.2 RadiSysCP816-AC
Figure16
ConnectorsandswitchesoftheCP816-AC
ICH3-S
MCH
CPU
SW3
J11 J12 J13 J14
SW3
DN70407209
OFF
1
2
3
4
5
6
ON
12
11
10
9
8
7
12.2.1 EquippingDIMMmodules
SelectingDualChannelMode
WhenequippingDIMMmodulesforDualChannelMode,notethatDIMMmodulesmust
beequippedinpairs.Therefore,fillfirstJ14andJ13andJ12andJ11second.
58
WhenusingDualChannelMode,parallelDIMMslots(i.e.J14andJ13,for
example)musthaveidenticalDIMMs(anidenticalDIMMmeansanidentical
NokiaSiemensNetworksC-code).DIMMsinserieswithinamemorychannel
donothavetobeidentical(i.e.J14andJ12,forexample).Forexample,there
canbe512MBDIMMsinslotsJ14andJ13and1GBDIMMsinslotsJ12and
J11.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
CP816-ACC111134
SelectingSingleChannelMode
WhenequippingDIMMmodulesforSingleChannelMode,fillfirstJ14andJ12second.
DualChannelModeisdefault.SingleChannelModeisusedonlyifsospecified
indeliveryspecificdocumentation.
12.2.2 DIP-switchsettings
Thefollowingsettingsaremadewithmicroswitchseethetablebelow:
Interchangeabilitycode
MBIFstatus(inuse/notinuse).
Table29
SW3switchsettings.
Switch1
Setting
Meaning
1-12
OFF*)
Interchangeabilitycodebit3
2-11
OFF*)
Interchangeabilitycodebit2
3-10
OFF*)
Interchangeabilitycodebit1
4-9
OFF*)
Interchangeabilitycodebit0
5-8
OFF
Notinuse
6-7
OFF
MessageBusInterface(MBIF)status:OFF=
MBIFinuse(bitD3inregister104hreads0).
InNEinstallations,whenEMBisused,thissetting
mustbeON=MBIFnotinuse.
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table30
Interchangeabilitycode(ICC)settings(SW3).
ICCcode
Switchsetting
Issue:2-9
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
DN70630644
59
CP816-ACC111134
Table30
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Interchangeabilitycode(ICC)settings(SW3).(Cont.)
ICCcode
Switchsetting
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
60
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
ETIP1-AC111193
13 ETIP1-AC111193
Figure17
DIPswitchesofplug-inunitETIP1-A
J5
J4
J2
S2
S1
S3
J1
DN70626863
Standardsettingsarepresentedinthetablebelow,andtheDIPswitchesmustbesetas
shownduringnormaloperation.
Therearenoalternativesettingsavailableontheplug-inunit.
DIPswitchS1isusedforsettingtheinterchangeabilitycodeoftheplug-inunitwhen
required,seethetablebelow.
Standardsettings(S2andS3)
Table31
StandardsettingsofETIP1-A(DIPswitchS2andS3)
DIPswitch
1-8
2-7
3-6
4-5
Meaning
S2
OFF
OFF
OFF
OFF
watchdogenabled-defaultvalue
OFF
OFF
OFF
ON
watchdogdisabled
allotherswitchpositionsarereservedfor
futureuse
OFF
OFF
OFF
OFF
Reservedforfutureuse-defaultvalue
S3
Issue:2-9
DN70630644
61
ETIP1-AC111193
Table31
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
StandardsettingsofETIP1-A(DIPswitchS2andS3)(Cont.)
DIPswitch
1-8
2-7
3-6
4-5
Meaning
allotherswitchpositionsarereservedfor
futureuse
Interchangeabilitycodesettings(S1)
Table32
62
InterchangeabilitycodesettingsofETIP1-A(DIP-SwitchS1))
ICCcode
S1settings
Switch
1-8
2-7
3-6
4-5
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
ON
ON
OFF
ON
ON
ON
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
ETIP1-AC111193
"A"isthedefaultvalueoftheICCcode(allswitchesOFF)
Issue:2-9
DN70630644
63
ETPC111826
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
14 ETPC111826
Jumperblocksoftheplug-inunit
Figure18
Jumpergroupoftheplug-inunitETP
Daughterboard
41
P5
S1
P4
P2
S1
P1
4 3 2 1
ON
W11
1
DN0951036ETP-A
Mainboard
W11
4
5
6
3
2
1
14.1 Jumpers
Table33
StandardsettingsofW11
Jumper
Setting
Meaning
1-6
OFF
OcteonWatchdogisenabled
2-5
OFF
Baudrate9600isselected
3-4
OFF
ForcedbootfromFLASH1isdisabled
14.2 DIP-switches
Standardsettings
Jumpersforthesestandardsettingsaresetatthefactory,andnormallythereisnoneed
tochangethem.
64
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table34
InterchangeabilitycodesettingsofETP
ICCcode
Switchsettings
1-8
2-7
3-6
4-5
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
ON
ON
OFF
ON
ON
ON
Table35
Issue:2-9
ETPC111826
InterchangeabilitycodesettingswithDIP-switchS1
Switch
Default
setting
Function
1-8
OFF
Interchangeabilitycodebit0
2-7
OFF
Interchangeabilitycodebit1
DN70630644
65
ETPC111826
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table35
66
InterchangeabilitycodesettingswithDIP-switchS1(Cont.)
Switch
Default
setting
Function
3-6
OFF
Interchangeabilitycodebit2
4-5
OFF
Interchangeabilitycodebit3
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
ETP-AC111828
15 ETP-AC111828
Jumperblocksoftheplug-inunit
Figure19
Jumpergroupoftheplug-inunitETP-A
Daughterboard
41
P5
S1
P4
P2
S1
P1
4 3 2 1
ON
W11
1
DN0951036ETP-A
Mainboard
W11
4
5
6
3
2
1
15.1 Jumpers
Table36
StandardsettingsofW11
Jumper
Setting
Meaning
1-6
OFF
OcteonWatchdogisenabled
2-5
OFF
Baudrate9600isselected
3-4
OFF
ForcedbootfromFLASH1isdisabled
15.2 DIP-switches
Standardsettings
Jumpersforthesestandardsettingsaresetatthefactory,andnormallythereisnoneed
tochangethem.
Issue:2-9
DN70630644
67
ETP-AC111828
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table37
ICCcode
Switchsettings
1-8
2-7
3-6
4-5
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
ON
ON
OFF
ON
ON
ON
Table38
68
InterchangeabilitycodesettingsofETP-A.
InterchangeabilitycodesettingswithDIP-switchS1.
DIPSwitch
Default
setting
Function
1-8
OFF
Interchangeabilitycodebit0
2-7
OFF
Interchangeabilitycodebit1
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table38
Issue:2-9
ETP-AC111828
InterchangeabilitycodesettingswithDIP-switchS1.(Cont.)
DIPSwitch
Default
setting
Function
3-6
OFF
Interchangeabilitycodebit2
4-5
OFF
Interchangeabilitycodebit3
DN70630644
69
ETS2C109474
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
16 ETS2C109474
Figure20
JumpersandmicroswitchesoftheETS2
J4
SW1
SW2
SW1,SW2
OFFON
J2
1
2
3
4
8
7
6
5
W3
4
5
6
W3
3
2
1
J1
DN05158998
JumperW3settings
ThesettingoftheJumperW3ispresentedinthetablebelow(W3).Thisjumperisnot
setduringnormaloperation.
Table39
Pins
JumperW3settings.
Whennotconnected/whenconnected
Externalwatchdogenabled/Externalwatchdogdisabled
BackplaneconnectorJTAGselected/EmulatorconnectorW4
JTAGselected
RSTCONFsignalpulledlow/RSTCONFsignalconnectedto
Vcc
InterchangeabilitysettingsSW1
Thesettingoftheinterchangeabilitycodeispresentedinthetablebelow(SW1).
70
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table40
ETS2C109474
Interchangeabilitycode(ICC)settings(SW1).
ICCcode
Setting
45
3-6
2-7
1-8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Unitconfigurationsettings
Theunitconfigurationsettingsarepresentedinthetablebelow(SW2).
Table41
Configurationsettings(SW2).
Switch
Defaultsetting
Function
1-8
OFF
WidthoftheHDLClink:
OFF=16x64kbit/s,ON=8x64kbit/s
Issue:2-9
DN70630644
71
ETS2C109474
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table41
Configurationsettings(SW2).(Cont.)
2-7
OFF
Reservedforfutureuse
3-6
OFF
1F#0ETPmode:
OFF=normalmode,ON=ETPmode
4-5
OFF
1F#1ETPmode:
OFF=normalmode,ON=ETPmode
72
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
ET16C109519
17 ET16C109519
TheET16hastwovendorsthatdifferinlayoutandfunctionoftheinterfaceswitch.They
canbedistinguishedfromeachotherbythedifferencesinthePWB.
17.1 EmersonET16(versions1-4)
Figure21
JumpersandmicroswitchesoftheEmersonET16(version1)
P5
P4
SW1
B2
Lineinterfacemode
OFF
SW1
ON
P2
Interchangeability
7 5 3 1
P1
B2
8 6 4 2
DN0596334
Configurationsettings
Thelineinterfacemodesettingsarepresentedinthetablebelow(SW1).Lineinterface
modecanbeoverriddenbySWsettings
Issue:2-9
Switch
Function
OFF
OFF
E1(default)
OFF
ON
T1
DN70630644
73
ET16C109519
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
E1settingappliestobothsymmetric(120)andasymmetric(75)interfaces.
Conversionfromsymmetrictoasymmetricisrealizedinconnectorpanel
CPETC.ConnectorpanelCPETSisneededforsymmetricE1interface.
17.2 EmersonET16(version5onwards)
Figure22
JumpersandmicroswitchesoftheEmersonET16(version5onwards)
P5
SW1
P4
W2
Lineinterfacemode
SW1
2
ON
OFF
1
P2
Interchangeability
W2
P1
DN0950516
Configurationsettings
Thelineinterfacemodesettingsarepresentedinthetablebelow(SW1).Lineinterface
modecanbeoverriddenbySWsettings
74
Switch
Function
OFF
OFF
E1(default)
OFF
ON
T1
E1settingappliestobothsymmetric(120)andasymmetric(75)interfaces.
Conversionfromsymmetrictoasymmetricisrealizedinconnectorpanel
CPETC.ConnectorpanelCPETSisneededforsymmetricE1interface.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
ET16C109519
17.3 InterphaseET16
Figure23
JumpersandmicroswitchesoftheInterphaseET16
P5
ON
P4
SW1
OFF
1
2 4 6 8 10
W1
W1
SW1
P2
1
3 5 7 9
P1
DN70480735
Configurationsettings
Thelineinterfacemodesettingsarepresentedinthetablebelow(SW1).Lineinterface
modecanbeoverriddenbySWsettings
Issue:2-9
Switch
Function
OFF
OFF
JT1
OFF
ON
T1
ON
OFF
E1/75R(notin
use)
ON
ON
E1/120R
DN70630644
75
ET16C109519
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
E1settingappliestobothsymmetric(120)andasymmetric(75)interfaces.
Conversionfromsymmetrictoasymmetricisrealizedinconnectorpanel
CPETC.ConnectorpanelCPETSisneededforsymmetricE1interface.
17.4 Interchangeabilitysettings
Thesettingoftheinterchangeabilitycodeispresentedinthetablebelow(B2/W2/W1).
Table42
76
Interchangeabilitycode(ICC)settings(B2/W2/W1).
ICCcode
Setting
7-8
5-6
3-4
1-2
ON
ON
ON
ON
ON
ON
ON
OFF
ON
ON
OFF
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
HWAT-AC08950
18 HWAT-AC08950
Figure24
Jumpersoftheplug-inunitHWAT-A
J5
W1
PRTA
J4
W2
J3
Standard
settings
W3
W3
W10
43
43
12
12
43
Alternative
settings
W4
W2
12
W10
Interchangeability
W5
J1
W4
1
2
3
4
8
7
6
5
DN98618576
Standardsettingsarepresentedinthetablebelow,andthejumpersW3andW10must
besetasshownduringnormaloperation.
AlternativesettingsonjumpergroupsW2dependontheapplicationaspresentedinthe
tablebelow.
JumpergroupW4isusedforsettingtheinterchangeabilitycodeoftheplug-inunitwhen
required,seethetablebelow.
Connectorswhichdonotrequirejumpers:
W1serviceandtestingconnectorPRTA,
andW5testconnectorforPCIbridgecircuits.
Standardsettings(W3,W10)
Table43
Issue:2-9
StandardsettingsofHWAT-A(W3,W10)
Jumper
Setting
Meaning
W3;1-2
ON
ClocksignalconnectedtoCPU
W3;3-4
OFF
W10;1-2
OFF
Oscillatorforforcedstart-up
DN70630644
77
HWAT-AC08950
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table43
StandardsettingsofHWAT-A(W3,W10)(Cont.)
Jumper
Setting
Meaning
W10;3-4
OFF
counter,running
Alternativesettings(W2)
Table44
AlternativesettingsofHWAT-A(W2)
Jumper
Setting
Meaning
BranchingofSBUS(SupervisionBus)
W2;2-3
ON
SBUSisnotbranched.
W2;1-4
OFF
Cabinetsinonerow;forexample,DXHLR,
CompactDXMSC,SGSN,SRRi,CPS,
CDS,HSS,IPTGateway,andBSC3i
MSS(IftheIPCHisnotthefirstcabinetintherow,
nextto1Acabinet)
W2;2-3
OFF
SBUSbranched.
W2;1-4
OFF
Cabinetsinseveralrows;forexample,
DXMSC,TransitDXMSC
Cabinetsinonerow;forexample
MSS(IftheIPCHisthefirstcabinetintherow,next
to1Acabinet)
Interchangeabilitycodesettings(W4)
Table45
78
InterchangeabilitycodesettingsofHWAT-A(W4)
ICCcode
W4settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table45
Issue:2-9
HWAT-AC08950
InterchangeabilitycodesettingsofHWAT-A(W4)(Cont.)
ICCcode
W4settings
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DN70630644
79
HWAT-BC111250
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
19 HWAT-BC111250
Figure25
Jumpersoftheplug-inunitHWAT-B
J5
W4
W6
Alternative
settings
W1
J1
Interchangeability
W4
1
2
3
4
12
W6
W1
43
Standard
settings
12
J3
43
J4
8
7
6
5
DN70584281
Standardsettingsarepresentedinthetablebelow,andthejumperW6mustbesetas
shownduringnormaloperation.
AlternativesettingsonjumpergroupsW1dependontheapplicationaspresentedinthe
tablebelow.
JumpergroupW4isusedforsettingtheinterchangeabilitycodeoftheplug-inunitwhen
required,seethetablebelow.
Otherconnectorsdonotrequirejumpers.
Standardsettings(W6)
Table46
80
StandardsettingsofHWAT-B(W6)
Jumper
Setting
Meaning
W6;2-3
OFF
ClocksignalconnectedtoCPU
W6;1-4
ON
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
HWAT-BC111250
Alternativesettings(W1)
Table47
AlternativesettingsofHWAT-B(W1)
Jumper
Setting
Meaning
BranchingofSBUS(SupervisionBus)
W1;2-3
OFF
SBUSisnotbranched.
W1;1-4
ON
Cabinetsinonerow;forexample,DXHLR,
CompactDXMSC,SGSN,SRRi,CPS,
CDS,HSS,IPTGateway,andBSC3i
MSS(IftheIPCHisnotthefirstcabinetintherow,
nextto1Acabinet)
W1;2-3
OFF
SBUSisbranched.
W1;1-4
OFF
Cabinetsinseveralrows;forexample,
DXMSC,TransitDXMSC
Cabinetsinonerow;forexample
MSS(IftheIPCHisthefirstcabinetintherow,
nextto1Acabinet)
Interchangeabilitycodesettings(W4)
Table48
Issue:2-9
InterchangeabilitycodesettingsofHWAT-B(W4)
ICCcode
W4settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
DN70630644
81
HWAT-BC111250
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table48
82
InterchangeabilitycodesettingsofHWAT-B(W4)(Cont.)
ICCcode
W4settings
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
PCU2-DC108407
20 PCU2-DC108407
ThejumpergroupsandLEDindicatorsofthePCU2-Dplug-inunitareshowninthe
figurebelow.
Figure26
Theconnectors,LEDindicatorsandDIPswitchgroupofthePCU2-D
W1
J7
J8
W3
J6
J1
Daughterboard
W4
J2
LD1
LD2
LD3
PQII_1
PQII_0
W5
W6
LD4
W2
Daughterboard
W5
1
2
3
6
5
4
W6
4
5
6
3
2
1
J5
J3
DN0484195
DIP-switch
W201
ON OFF
4
3
2
1
TherearetwoswitchesforjumpersettingsontheprimarysideofthePCU2-D:The6-pin
W5isusedforindicatingtheplaceofthePCM,selectingMII-MUXmode,andfor
selecting4Mor8MPCM.The6-pinW6isusedforselectingoftheemulator,disabling
thewatchdog,andforselectingthedebuggingmode.Therearealsotwoswitchesthat
theuserdoesnothavetoset,namely:W1fortestingsideselectionandW2forJTAG
chainselection.Inaddition,therearetwoemulators,W3(PQII_1)andW4(PQII_0).
OnthesecondarysideofthePCU2-D,thereisamicroswitchW201forsettingthe
interchangeabilitycode.
W5
ThetablebelowpresentstheuseofW5.
Issue:2-9
DN70630644
83
PCU2-DC108407
Table49
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
TheuseofW5.
Selectioncriteria
Setting
Explanation
ThePCMinplace
1-6
0=PCM5;PCMfromcartridgecrossconnection
1=PCM3;PCMstraightfromGroupSwitch
SettingMII-MUXmode
2-5
0=MII-MUXactive
1=MII-MUXbypass
4M/8M
3-4
0=4M
1=8M
0=thejumperisoff;1=thejumperison
W6
ThetablebelowpresentstheuseofW6.
Table50
TheuseofW6.
SelectionCriteria
Setting
Explanation
Selectionofemulator
1-6
0=Emulatornotinplace
1=Emulatorinplace
Watchdogdisabled
2-5
0=Watchdognotdisabled
1=Watchdogdisabled
Debuggermode
3-4
0=Debuggermodenotselected
1=Debuggermodeselected
0=thejumperisoff;1=thejumperison
W201
Interchangeabilitycodeissetwitha4-switchDIP-switchgrouplocatedonthesecondary
sideofthecircuitboardofthePCU2-D(seethetablebelow).
84
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table51
PCU2-DC108407
Settingtheinterchangeabilitycode.
Code
Jumpersetting
Switch1
(MSB)
Switch2
Switch3
Switch4
(LSB)
Off
Off
Off
Off
Off
Off
Off
On
Off
Off
On
Off
Off
Off
On
On
Off
On
Off
Off
Off
On
Off
On
Off
On
On
Off
Off
On
On
On
On
Off
Off
Off
On
Off
Off
On
On
Off
On
Off
On
Off
On
On
On
On
Off
Off
On
On
Off
On
On
On
On
Off
TheuseoflettersI,OandQasinterchangeabilitycodesisnotallowed.
PCU2-DjumpersettingsinBSC3i
ThefollowinginformationisspecificallyforBSC3inetworkelements.
W5
ThetablebelowpresentstheuseofW5forPCU2-DinBSC3i.
Issue:2-9
DN70630644
85
PCU2-DC108407
Table52
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
TheuseofW5forPCU2-DinBSC3i.
Selectioncriteria
Setting
Explanation
ThePCMinplace
1-6
0=PCM5;PCU2-DconnectedtoGSWB
1=PCM3;PCU2-DconnectedtoGSW1KB/GSW2KB
SettingMII-MUXmode
2-5
0=MII-MUXactive
SelectionofPCMmode
3-4
0=4M;PCU2-Dequippedtoslots06and07
1=8M;PCU2-Dequippedtoslots03,04and05
0=thejumperisoff;1=thejumperison
W6
ThetablebelowpresentstheuseofW6forPCU2-DinBSC3i.
Table53
TheuseofW6forPCU2-DinBSC3i.
Selectioncriteria
Setting
Explanation
Selectionofemulator
1-6
0=Emulatornotinplace
Watchdogdisabled
2-5
0=Watchdognotdisabled
Debuggermode
3-4
0=Debuggermodenotselected
0=thejumperisoff;1=thejumperison
86
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
PCU2-EC110629
21 PCU2-EC110629
Figure27
Jumpers,DIPswitchandbackplaneconnectorsofplug-inunitPCU2-E
W1
J5
W1
3
4
2
1
W12
1
2
4
3
J2
W12
4 3
W13
W13
SW1
1 2
Interchangeability
ON
SW1
J1
1 2 3 4
OFF
DN70557278
Standardsettingsarepresentedinthetablebelow,thejumpersmustbesetasshown
duringnormaloperation.
Therearenoalternativesettingsavailableontheplug-inunit,exceptforjumperW1.
DIPswitchSW1isusedforsettingtheinterchangeabilitycodeoftheplug-inunitwhen
required,seethetablebelow.
Table54
SettingsofPCU2-EinBSC3i660GSWB(W1)
Strapping
group
Strapping
Settingin
BSC3i660
GSWB
Function
W1
1-4
OFF
PCMinterface8Mbit/s.
W1
2-3
ON
SharedPCM(J5row6/7)used,interfaces4Mbit/s.
Issue:2-9
DN70630644
87
PCU2-EC110629
Table55
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SettingsofPCU2-EinBSC3i660GSW1KB(W1)
Strapping
group
Strapping
Settingin
BSC3i660
GSW1KB
Function
W1
1-4
ON
PCMinterface4Mbit/s.
W1
2-3
OFF
4M/8MsharedPCMmodenotinuse.
Table56
SettingsofPCU2-EinBSC3i1000/2000(W1)
Strapping
group
Strapping
Settingin
BSC3i
1000/2000
Function
W1
1-4
ON
PCMinterface4Mbit/s(intracks6-7).
OFF
PCMinterface8Mbit/s(intracks3-5).
OFF
4M/8MsharedPCMmodenotinuse.
W1
Table57
2-3
SettingsofPCU2-EinUpgratedFlexiBSC(W1)
Strapping
group
Strapping
Settingin
Upgraded
FlexiBSC
(M98HW)
Function
W1
1-4
ON
PCMinterface4Mbit/s.SelectedforPCU2-Esinslots0607inBCSUs0-3.
OFF
PCMinterface8Mbit/s.SelectedforPCU2-Esinslots0305inBCSUs0-3andinslots03-07inBCSUs4-6.
OFF
4M/8MsharedPCMmodenotinuse.
W1
Table58
2-3
SettingsofPCU2-EinNewdeliveredFlexiBSC(W1)
Strapping
group
Strapping
SettinginNew
FlexiBSC
Function
W1
1-4
ON
PCMinterface4Mbit/s.SelectedforPCU2-Esinslots0307inBCSU0.
88
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table58
PCU2-EC110629
SettingsofPCU2-EinNewdeliveredFlexiBSC(W1)(Cont.)
Strapping
group
Strapping
SettinginNew
FlexiBSC
Function
OFF
PCMinterface8Mbit/s.SelectedforPCU2-Esinslots0307inBCSUs1-6.
OFF
4M/8MsharedPCMmodenotinuse.
W1
Table59
2-3
StandardsettingsofPCU2-EinFlexiBSC(W12)
Strapping
group
Strapping
Defaultsetting Function
inFlexiBSC
W12
1-2
OFF
RS-232portspeedis9600bps.(Default)
W12
3-4
OFF
IPETCcartridgeusageisdisabled.(Default)
Table60
StandardsettingsofPCU2-EinFlexiBSC(W13)
Strapping
group
Strapping
Defaultsetting Function
inFlexiBSC
W13
1-2
OFF
MPC8567emulatorisdisabled.(default)
W13
3-4
OFF
MPC8567watchdogisenabled.(default)
Interchangeabilitycodesettings(SW1)
Table61
Issue:2-9
InterchangeabilitycodesettingsofPCU2-E(SW1)
ICCcode
SW1settings
Switch1(MSB)
Switch2
Switch3
Switch4(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
DN70630644
89
PCU2-EC110629
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table61
ICCcode
SW1settings
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
90
InterchangeabilitycodesettingsofPCU2-E(SW1)(Cont.)
TheuseoflettersI,OandQasinterchangeabilitycodesisnotallowed.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SBMUX-AC110546
22 SBMUX-AC110546
Figure28
Connectors,microswitchandsettingsoftheSBMUX-A.
P5
P4
SW1
SW4 SW5
SW3
SW2
SW6
P3
SW1-6
8 7 6 5
P2
ON
OFF
1 2 3 4
P1
DN05160087
TheSBMUX-Ahassixmicroswitchpackageswithfourswitcheseach.Theswitchesare
usedforsettingPCMmode,SerialBroadbandInterfacecapacityandInterchangeability
code.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
Table62
Issue:2-9
PCMmodesettingsontheSBMUX-A(SW1).
Switch
Defaultsetting Function
1-8
OFF(4M)
4M/8MmodeforPCMcircuits0127OFF4Mmodeselected:
PCMcircuits063areconnectedthroughR0R31,T0T31
serialbuses.ON8Mmodeselected:PCMcircuits0127are
connectedthroughR0R31,T0T31serialbuses.
2-7
OFF(4M)
4M/8MmodeforPCMcircuits128255OFF4Mmodeselected:
PCMcircuits128191areconnectedthroughR32R63,
T32T64serialbuses.ON8Mmodeselected:PCMcircuits128
255areconnectedthroughR32R63T32T63serialbuses.
DN70630644
91
SBMUX-AC110546
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table62
PCMmodesettingsontheSBMUX-A(SW1).(Cont.)
3-6
Reserved
4-5
Reserved
Interchangeabilitycodesettings(SW2)
Thesettingoftheinterchangeabilitycode(ICCcode)ispresentedinthetablebelow.
Table63
InterchangeabilitysettingsontheSBMUX-A(SW2).
Switch
Defaultsetting
Function
1-8
OFF
Interchangeabilitycodebit3
2-7
OFF
Interchangeabilitycodebit2
3-6
OFF
Interchangeabilitycodebit1
4-5
OFF
Interchangeabilitycodebit0
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table64
Interchangeabilitycode(ICC)settings(SW2).
ICCcode
Switchsetting
Switch1
Switch2
Switch3
Switch4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
92
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table64
SBMUX-AC110546
Interchangeabilitycode(ICC)settings(SW2).(Cont.)
ICCcode
Switchsetting
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table65
Issue:2-9
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).
Switch
Function
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits015areconnectedthroughSerialBroadband1interface.
OFF
ON
OFF
OFF
PCMcircuits031areconnectedthroughSerialBroadband1interface.
ON
ON
OFF
OFF
PCMcircuits047areconnectedthroughSerialBroadband1interface.
OFF
OFF
ON
OFF
PCMcircuits063areconnectedthroughSerialBroadband1interface.
DN70630644
93
SBMUX-AC110546
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table65
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).(Cont.)
Switch
Function
ON
OFF
ON
OFF
PCMcircuits079areconnectedthroughSerialBroadband1interface.
OFF
ON
ON
OFF
PCMcircuits095areconnectedthroughSerialBroadband1interface.
ON
ON
ON
OFF
PCMcircuits0111areconnectedthroughSerialBroadband1interface.
OFF
OFF
OFF
ON
PCMcircuits0127areconnectedthroughSerialBroadband1interface.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table66
94
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).
Switch
Function
OFF
OFF
OFF
OFF
SB2interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits6479areconnectedthroughSerialBroadband2interface.
OFF
ON
OFF
OFF
PCMcircuits6495areconnectedthroughSerialBroadband2interface.
ON
ON
OFF
OFF
PCMcircuits64111areconnectedthrough
SerialBroadband2interface.
OFF
OFF
ON
OFF
PCMcircuits64127areconnectedthrough
SerialBroadband1interface.
ON
OFF
ON
OFF
PCMcircuits64143areconnectedthrough
SerialBroadband2interface.
OFF
ON
ON
OFF
PCMcircuits64159areconnectedthrough
SerialBroadband2interface.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table66
SBMUX-AC110546
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).(Cont.)
Switch
Function
ON
ON
ON
OFF
PCMcircuits64175areconnectedthrough
SerialBroadband2interface.
OFF
OFF
OFF
ON
PCMcircuits64191areconnectedthrough
SerialBroadband2interface.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table67
Issue:2-9
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).
Switch
Function
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits128143areconnectedthrough
SerialBroadband3interface.
OFF
ON
OFF
OFF
PCMcircuits128159areconnectedthrough
SerialBroadband3interface.
ON
ON
OFF
OFF
PCMcircuits128175areconnectedthrough
SerialBroadband3interface.
OFF
OFF
ON
OFF
PCMcircuits128191areconnectedthrough
SerialBroadband3interface.
ON
OFF
ON
OFF
PCMcircuits128207areconnectedthrough
SerialBroadband3interface.
OFF
ON
ON
OFF
PCMcircuits128223areconnectedthrough
SerialBroadband3interface.
ON
ON
ON
OFF
PCMcircuits128239areconnectedthrough
SerialBroadband3interface.
OFF
OFF
OFF
ON
PCMcircuits128255areconnectedthrough
SerialBroadband3interface.
DN70630644
95
SBMUX-AC110546
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandinterfaceSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table68
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).
Switch
Function
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits192207areconnectedthrough
SerialBroadband4interface.
OFF
ON
OFF
OFF
PCMcircuits192223areconnectedthrough
SerialBroadband4interface.
ON
ON
OFF
OFF
PCMcircuits192239areconnectedthrough
SerialBroadband4interface.
OFF
OFF
ON
OFF
PCMcircuits192255areconnectedthrough
SerialBroadband4interface.
ON
OFF
ON
OFF
Notspecified
OFF
ON
ON
OFF
Notspecified
ON
ON
ON
OFF
Notspecified
OFF
OFF
OFF
ON
Notspecified
SBMUX-AjumpersettingsincombinedBSC/TCSMinstallationwhere
BSCpartiseitherupgradedFlexiBSCornewdeliveryFlexiBSC
ThefollowinginformationisspecificallyforcombinedFlexiBSC/TCSM3inetwork
elements.
PCMmodesettings(SW1)
96
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table69
SBMUX-AC110546
PCMmodesettingsontheSBMUX-A(SW1).
SW1
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SBMUX-A
01
ON
ON
OFF
OFF
InternalPCMs0-255
8Mmodeselected
SBMUX-A
02
ON
ON
OFF
OFF
InternalPCMs0-255
8Mmodeselected
SerialBroadband1Interfacesettings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table70
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).
SW3
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SBMUX-A
01
ON
ON
OFF
OFF
SB1interface,internalPCMcircuits047connected.
SBMUX-A
02
ON
ON
OFF
OFF
SB1interface,internalPCMcircuits047connected.
SerialBroadbandSB2settings(SW4),alternative1,Equipment
protectioninuse
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table71
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).
SW4
SBMUX-A
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB2interface,internalPCMcircuits64127connected.A)
WhenTCSA0cabinetisinquestion,
DN70630644
97
SBMUX-AC110546
Table71
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).(Cont.)
SW4
Switch
selectedifSB1interfacesofETS2/ETIP1-AinGTIC
2slot05andSB1interfacesofETS2/ETIP1-AinGTIC
3slot05connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
intefacesofETS2/ETIP1-AinGTIC
5slot05andSB1intefacesofETS2/ETIP1-AinGTIC
6slot05connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
8slot05andSB1interfacesofETS2/ETIP1-AinGTIC
9slot05connected.
SBMUX-A
02
OFF
OFF
ON1)
OFF
SB2interface,internalPCMcircuits64127connected.A)
WhenTCSA0cabinetisinquestion,
selectedifSB2interfacesofETS2/ETIP1-AinGTIC
2slot06andSB2interfacesofETS2/ETIP1-AinGTIC
3slot06connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB2
intefacesofETS2/ETIP1-AinGTIC
5slot06andSB2intefacesofETS2/ETIP1-AinGTIC
6slot06connected.
98
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table71
SBMUX-AC110546
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).(Cont.)
SW4
Switch
C)WhenTCSA2
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
8slot06andSB2interfacesofETS2/ETIP1-AinGTIC
9slot06connected.
1)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
SerialBroadbandSB2settings(SW4),alternative2,Transmission
protectioninuse
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table72
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).
SW4
SBMUX-A
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB2interface,internalPCMcircuits64127connected.A)
WhenTCSA0cabinetisinquestion,
selectedifSB1interfacesofETS2/ETIP1-AinGTIC
2slot05connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
5slot05connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
8slot05connected.
Issue:2-9
DN70630644
99
SBMUX-AC110546
Table72
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).(Cont.)
SW4
SBMUX-A
Switch
02
OFF
OFF
ON1)
OFF
SB2interface,internalPCMcircuits64127connected.A)
WhenTCSA0cabinetisinquestion,
selectedifSB1interfacesofETS2/ETIP1-AinGTIC
3slot05connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
6slot05connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
9slot05connected.
1)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF.
SerialBroadbandSB3settings(SW5),alternative1,Equipment
protectioninuse
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table73
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).
SW5
SBMUX-A
100
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB3interface,internalPCMcircuits
128-191connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
2slot05andSB2in-
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table73
SBMUX-AC110546
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).(Cont.)
SW5
Switch
terfacesofETS2/ETIP1-AinGTIC
3slot05connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
5slot05andSB2interfacesofETS2/ETIP1-AinGTIC
6slot05connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
8slot05andSB2interfacesofETS2/ETIP1-AinGTIC
9slot05connected.
SBMUX-A
02
OFF
OFF
ON1)
OFF
SB3interface,internalPCMcircuits
128-191connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
2slot07andSB1interfacesofETS2/ETIP1-AinGTIC
3slot07connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
5slot07andSB1interfacesofETS2/ETIP1-AinGTIC
6slot07connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
Issue:2-9
DN70630644
101
SBMUX-AC110546
Table73
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).(Cont.)
SW5
Switch
8slot07andSB1interfacesofETS2/ETIP1-AinGTIC
9slot07connected.
1)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
SerialBroadbandSB3settings(SW5),alternative2,Transmission
protectioninuse
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table74
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).
SW5
SBMUX-A
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB3interface,internalPCMcircuits
128-191connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
2slot05connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
5slot05connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
8slot05connected.
SBMUX-A
102
02
OFF
OFF
ON1)
DN70630644
OFF
SB3interface,internalPCMcircuits
128-191connected.
A)WhenTCSA0
cabinetisinques-
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table74
SBMUX-AC110546
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).(Cont.)
SW5
Switch
tion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
3slot05connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
6slot05connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
9slot05connected.
1)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
SerialBroadbandinterfaceSB4settings(SW6),alternative1,
Equipmentprotectioninuse
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table75
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).
SW6
SBMUX-A
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB4interface,internalPCMcircuits
192-255connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
2slot06andSB1interfacesofETS2/ETIP1-AinGTIC
3slot06connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
Issue:2-9
DN70630644
103
SBMUX-AC110546
Table75
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).(Cont.)
SW6
Switch
interfacesofETS2/ETIP1-AinGTIC
5slot06andSB1interfacesofETS2/ETIP1-AinGTIC
6slot06connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
8slot06andSB1interfacesofETS2/ETIP1-AinGTIC
9slot06connected.
SBMUX-A
02
OFF
OFF
ON1)
OFF
SB4interface,internalPCMcircuits
192-255connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
2slot07andSB2interfacesofETS2/ETIP1-AinGTIC
3slot07connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
5slot07andSB2interfacesofETS2/ETIP1-AinGTIC
6slot07connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB2
interfacesofETS2/ETIP1-AinGTIC
8slot07andSB2interfacesofETS2/ETIP1-AinGTIC
9slot07connected.
1)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
104
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SBMUX-AC110546
SerialBroadbandinterfaceSB4settings(SW6),alternative2,
Transmissionprotectioninuse
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table76
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).
SW6
SBMUX-A
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB4interface,internalPCMcircuits
192-255connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
2slot06connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
5slot06connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
8slot06connected.
SBMUX-A
02
OFF
OFF
ON1)
OFF
SB4interface,internalPCMcircuits
192-255connected.
A)WhenTCSA0
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
3slot06connected.
B)WhenTCSA1
cabinetisinquestion,selectedifSB1
interfacesofETS2/ETIP1-AinGTIC
6slot06connected.
C)WhenTCSA2
cabinetisinquestion,selectedifSB1
Issue:2-9
DN70630644
105
SBMUX-AC110546
Table76
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).(Cont.)
SW6
Switch
interfacesofETS2/ETIP1-AinGTIC
9slot06connected.
1)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
SBMUX-AjumpersettingsincombinedBSC3i/TCSM3iinstallation
whereBSCpartiseitherBSC3i1000orBSC3i2000
ThefollowinginformationisspecificallyforcombinedBSC3i/TCSM3inetworkelements.
TCSA1&TCS2onlyincombinedBSC/TCSMinstallationwhereBSCpartisBSC3i
1000
PCMmodesettings(SW1)
Table77
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
PCMmodesettingsontheSBMUX-A(SW1).
SW1
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SBMUX-A
01
ON
ON
OFF
OFF
InternalPCMs0-255
8Mmodeselected
SBMUX-A
02
ON
ON
OFF
OFF
InternalPCMs0-255
8Mmodeselected
SerialBroadband1Interfacesettings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table78
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).
SW3
Switch
Slot
106
1(1-8)
2(2-7)
3(3-6)
DN70630644
4(4-5)
Note
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table78
SBMUX-AC110546
SerialBroadbandInterfaceSB1settingsontheSBMUX-A(SW3).(Cont.)
SW3
Switch
SBMUX-A
01
ON
ON
OFF
OFF
SB1interface,internalPCMcircuits047connected.
SBMUX-A
02
ON
ON
OFF
OFF
SB1interface,internalPCMcircuits047connected.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table79
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).
SW4
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SBMUX-A
01
OFF
OFF
ON1)
OFF
SB2interface,internalPCMcircuits64127connected.A)
WhenTC2C0cabinetisinquestion,
selectedifinterface
0ofETS2inGTIC2
slot05connected.B)
WhenTC2C1cabinetisinquestion,
selectedifinterface
0ofETS2inGTIC5
slot05connected.C)
WhenTC2C2cabinetisinquestion,
selectedifinterface
0ofETS2inGTIC8
slot05connected.
SBMUX-A
02
OFF
OFF
ON1)
OFF
SB2interface,internalPCMcircuits64127connected.A)
WhenTC2C0cabinetisinquestion,
selectedifinterface
0ofETS2inGTIC3
slot05connected.B)
WhenTC2C1cabinetisinquestion,
Issue:2-9
DN70630644
107
SBMUX-AC110546
Table79
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SerialBroadbandInterfaceSB2settingsontheSBMUX-A(SW4).(Cont.)
SW4
Switch
selectedifinterface
0ofETS2inGTIC6
slot05connected.C)
WhenTC2C2cabinetisinquestion,
selectedifinterface
0ofETS2inGTIC9
slot05connected.
1)IfETS2innotconnectedinthisPCMposition,switchmustbeOFF.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table80
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).
SW5
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SBMUX-A
01
OFF
OFF
ON1)
OFF
SB3interface,internalPCMcircuits
128-191connected.
A)WhenTC2C0
cabinetisinquestion,selectedifinterface1ofETS2in
GTIC2slot05connected.B)When
TC2C1cabinetisin
question,selectedif
interface1ofETS2
inGTIC5slot05
connected.C)When
TC2C2cabinetisin
question,selectedif
interface1ofETS2
inGTIC8slot05
connected.
SBMUX-A
02
OFF
OFF
ON1)
OFF
SB3interface,internalPCMcircuits
128-191connected.
A)WhenTC2C0
cabinetisinquestion,selectedifinter-
108
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table80
SBMUX-AC110546
SerialBroadbandInterfaceSB3settingsontheSBMUX-A(SW5).(Cont.)
SW5
Switch
face1ofETS2in
GTIC3slot05connected.B)When
TC2C1cabinetisin
question,selectedif
interface1ofETS2
inGTIC6slot05
connected.C)When
TC2C2cabinetisin
question,selectedif
interface1ofETS2
inGTIC9slot05
connected.
1)IfETS2innotconnectedinthisPCMposition,switchmustbeOFF.
SerialBroadbandinterfaceSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table81
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).
SW6
SBMUX-A
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON1)
OFF
SB4interface,internalPCMcircuits
192-255connected.
A)WhenTC2C0
cabinetisinquestion,selectedifinterface0ofETS2in
GTIC2slot06connected.B)When
TC2C1cabinetisin
question,selectedif
interface0ofETS2
inGTIC5slot06
connected.C)When
TC2C2cabinetisin
question,selectedif
interface0ofETS2
inGTIC8slot06
connected.
DN70630644
109
SBMUX-AC110546
Table81
SerialBroadbandInterfaceSB4settingsontheSBMUX-A(SW6).(Cont.)
SW6
SBMUX-A
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Switch
02
OFF
OFF
ON1)
OFF
SB4interface,internalPCMcircuits
192-255connected.
A)WhenTC2C0
cabinetisinquestion,selectedifinterface0ofETS2in
GTIC3slot06connected.B)When
TC2C1cabinetisin
question,selectedif
interface0ofETS2
inGTIC6slot06
connected.C)When
TC2C2cabinetisin
question,selectedif
interface0ofETS2
inGTIC9slot06
connected.
1)IfETS2innotconnectedinthisPCMposition,switchmustbeOFF.
110
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SERO-BC109453
23 SERO-BC109453
Figure29
JumperandmicroswitchsettingsoftheSERO-B
W1W2W3W4
J5
J4
W5W6W7W8
J3
W9
654
W1-W8
W10
123
W11
OFFON
SERO-B
Interchangeability
J1
W11
1
2
3
4
8
7
6
5
DN05209132
AlternativesettingsonjumpergroupsW1throughW8dependontheapplicationas
presentedinthetablebelow.
MicroswitchW11isusedforsettingtheinterchangeabilitycodeoftheplug-inunitwhen
required,seethetablebelow.
PinheadergroupsW9andW10areonlyforproductiontestingandprogramming
purposes.
Alternativesettings
Table82
AlternativesettingofSERO-B
Meaning
Jumper
Setting
CTS(ClearToSend)controlcomesfromanexternaldevice
W3;2-3
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W3;1-2
ON
W3;4-5
ON
Channel0(V.28)
Channel1(V.28)
CTS(ClearToSend)controlcomesfromanexternaldevice
Issue:2-9
DN70630644
111
SERO-BC109453
Table82
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
AlternativesettingofSERO-B(Cont.)
Meaning
Jumper
Setting
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W3;5-6
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W1;2-3
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W1;1-2
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W1;4-5
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W1;5-6
ON
V.28inuse:CTS(ClearToSend)controlcomesfromanexternaldevice
W4;2-3
ON
V.28inuse:ExternalCTScontrolnotused,settostate0(Defaultsetting)
W4;1-2
ON
V.11inuse
W4;1-2
ON
V.28inuse:CTS(ClearToSend)controlcomesfromanexternaldevice
W4;4-5
ON
V.28inuse:ExternalCTScontrolnotused,settostate0(Defaultsetting)
W4;5-6
ON
V.11inuse
W4;5-6
ON
V.28inuse:CTS(ClearToSend)comesfromanexternaldevice
W2;2-3
ON
V.28inuse:ExternalCTSnotused,settostate0(Defaultsetting)
W2;1-2
ON
V.11inuse
W2;1-2
ON
W2;4-5
ON
Channel2(V.28)
Channel3(V.28)
Channel4(V.28orV.11)
Channel5(V.28orV.11)
Channel6(V.28orV.11)
Channel7(V.28orV.11)
V.28inuse:CTS(ClearToSend)controlcomesfromanexternaldevice
112
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table82
SERO-BC109453
AlternativesettingofSERO-B(Cont.)
Meaning
Jumper
Setting
V.28inuse:ExternalCTScontrolnotused,settostate0(Defaultsetting)
W2;5-6
ON
V.11inuse
W2;5-6
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W8;2-3
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W8;1-2
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W8;4-5
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W8;5-6
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W7;2-3
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W7;1-2
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W7;4-5
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W7;5-6
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W5;2-3
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W5;1-2
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W5;4-5
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W5;5-6
ON
Channel8(V.28)
Channel9(V.28)
Channel10(V.28)
Channel11(V.28)
Channel12(V.28)
Channel13(V.28)
Channel14(V.28)
Issue:2-9
DN70630644
113
SERO-BC109453
Table82
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
AlternativesettingofSERO-B(Cont.)
Meaning
Jumper
Setting
CTS(ClearToSend)controlcomesfromanexternaldevice
W6;2-3
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W6;1-2
ON
CTS(ClearToSend)controlcomesfromanexternaldevice
W6;4-5
ON
ExternalCTScontrolnotused,settostate0(Defaultsetting)
W6;5-6
ON
Channel15(V.28)
Interchangeabilitysettings(W11)
Theinterchangeabilitycodeselection(microswitchW11)
Table83
InterchangeabilitycodesettingsofSERO-B(W11)
ICCcode
W11settings
1-8
2-7
3-6
4-5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
114
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table83
SERO-BC109453
InterchangeabilitycodesettingsofSERO-B(W11)(Cont.)
ICCcode
W11settings
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Issue:2-9
DN70630644
115
SWPRO-CC111169
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
24 SWPRO-CC111169
Thefigurebelowshowsthelayoutwithlocationoftheswitchesandtheconnectors.
SWPRO-CLayout
Figure30
DIPswitchesoftheplug-inunitSWPRO-C
SWE
Miscellaneous settings
SWE
P5
OFFON
ON
P4
8
7
6
5
2 3 4
SWB
1
2
3
4
SWA
P3
Interchangeability
SWA
OFFON
P2
ON
8
7
6
5
2 3 4
DN70573841
P1
1
2
3
4
Bootsource
SWB
OFFON
ON
8
7
6
5
2 3 4
1
2
3
4
Thereareotherpinheadersontheboardwhicharenotpresentedinthefigure.
OnlytheDIPswitcheswhichcanbesetbytheuseraredescribedhere.Donot
makeanychangestootherpinheaders,theyareusedforproduction,
debuggingandtestingpurposesonly.
Interchangeabilitycodesettings
TheInterchangeabilitySwitchBlock(SWA)consistsofa4positionDIPswitch.This
switchcontainsthefourinterchangeabilitycodebits.Theinterchangeabilitylinesdriveto
'0'whentheswitchesareOFF.
116
'OFF'isGND,'ON'isVCC.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table84
SWPRO-CC111169
Switchsettings(SWA).
Switch
DefaultSetting
Meaning
1-8
OFF*)
Interchangeabilitycodebit3(MSB)
2-7
OFF*)
Interchangeabilitycodebit2
3-6
OFF*)
Interchangeabilitycodebit1
4-5
OFF*)
Interchangeabilitycodebit0(LSB)
*)ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
ThetablebelowpresentsthesettingoftheinterchangeabilitycodeforSWPRO-C.
Table85
InterchangeabilitycodesettingsofSWPRO-C
ICCcode
Setting
SW18(MSB)
SW27
SW36
SW45(LSB)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
Issue:2-9
DN70630644
117
SWPRO-CC111169
Table85
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
InterchangeabilitycodesettingsofSWPRO-C(Cont.)
ICCcode
Setting
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
Bootsourceselection
Thebootsourceselectionswitchblock(SWB)consistsofa4-positionDIPswitch.
Switch
DefaultSetting Meaning
1-8
OFF
Notinuse.
2-7
OFF
Notinuse.
3-6
OFF
Notinuse.
4-5
ON
Bootmode.Defaultsetting.Donotchangethis
setting.
MiscellaneousSettings
Theswitchblock(SWE)isconnectedtofourinputsoftheFPGA(SW_IN3:0)andfor
miscellaneoususe.
Table86
118
Switchsettings(SWE).
Switch
DefaultSetting
Meaning
1-8
OFF
ClockPhaseControl0(SW_IN0)
2-7
OFF
ClockPhaseControl1(SW_IN1)
3-6
OFF
Reservedforfutureuse(SW_IN2)
4-5
OFF
Reservedforfutureuse(SW_IN3)
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SWPRO-CC111169
ThetablebelowpresentsthesettingofGSWBControlBusClockPhaseforSWPRO-C.
Table87
GSWBControlBusClockPhasecodesettings
ControlBusClock
Phase
Setting
SW18
SW27
SW36
SW45
Defaultsettingwith
normaltiming
OFF
OFF
OFF
OFF
15nsdelayedtiming
ON
OFF
OFF
OFF
15nsadvancedtiming
OFF
ON
OFF
OFF
30nsadvancedtiming
ON
ON
OFF
OFF
Issue:2-9
DN70630644
119
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
25 SW256BC109365
Figure31
Connectors,microswitchandsettingsoftheSW256B
P5
P4
SW1
SW4 SW5
SW3
SW2
SW6
P3
Interchangeability
/PCM/SBI
SW1-6
8 7 6 5
P2
ON
OFF
1 2 3 4
P1
DN05159767
TheSW256Bhassixmicroswitchpackageswithfourswitcheseach.Theswitchesare
usedforsettingPCMmode,SerialBroadbandInterfacecapacityandInterchangeability
code.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
Table88
120
PCMmodesettingsontheSW256B(SW1).
Switch
Default
setting
Function
1-8
OFF(4M)
4M/8MmodeforPCMcircuits0127OFF4Mmodeselected:
PCMcircuits063areconnectedthroughR0R31,T0T31
serialbuses.ON8Mmodeselected:PCMcircuits0127are
connectedthroughR0R31,T0T31serialbuses.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table88
SW256BC109365
PCMmodesettingsontheSW256B(SW1).(Cont.)
Switch
Default
setting
Function
2-7
OFF(4M)
4M/8MmodeforPCMcircuits128255OFF4Mmodeselected:
PCMcircuits128191areconnectedthroughR32R63,
T32T63serialbuses.ON8Mmodeselected:PCMcircuits128
255areconnectedthroughR32R63T32T63serialbuses.
3-6
Reserved
4-5
Reserved
Interchangeabilitycodesettings(SW2)
Thesettingoftheinterchangeabilitycode(ICCcode)ispresentedinthetablebelow.
Table89
InterchangeabilitysettingsontheSW256B(SW2).
Switch
Defaultsetting
Function
1-8
OFF
Interchangeabilitycodebit3
2-7
OFF
Interchangeabilitycodebit2
3-6
OFF
Interchangeabilitycodebit1
4-5
OFF
Interchangeabilitycodebit0
Thetablebelowpresentsthesettingoftheinterchangeabilitycode.
Table90
Interchangeabilitycode(ICC)settings(SW2).
ICCcode
Switchsetting
Switch1
Switch2
Switch3
Switch4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
Issue:2-9
DN70630644
121
SW256BC109365
Table90
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Interchangeabilitycode(ICC)settings(SW2).(Cont.)
ICCcode
Switchsetting
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
ThefirstinterchangeabilitycodeAcorrespondstoallswitchesOFF,afterwhichthe
settingsstarttorollforeachinterchangeabilitycodechange.
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table91
122
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).
Switch
Function
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits015areconnectedthroughSerialBroadband1interface.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table91
SW256BC109365
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
Switch
Function
OFF
ON
OFF
OFF
PCMcircuits031areconnectedthroughSerialBroadband1interface.
ON
ON
OFF
OFF
PCMcircuits047areconnectedthroughSerialBroadband1interface.
OFF
OFF
ON
OFF
PCMcircuits063areconnectedthroughSerialBroadband1interface.
ON
OFF
ON
OFF
PCMcircuits079areconnectedthroughSerialBroadband1interface.
OFF
ON
ON
OFF
PCMcircuits095areconnectedthroughSerialBroadband1interface.
ON
ON
ON
OFF
PCMcircuits0111areconnectedthroughSerialBroadband1interface.
OFF
OFF
OFF
ON
PCMcircuits0127areconnectedthroughSerialBroadband1interface.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table92
Issue:2-9
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).
Switch
Function
OFF
OFF
OFF
OFF
SB2interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits6479areconnectedthroughSerialBroadband2interface.
OFF
ON
OFF
OFF
PCMcircuits6495areconnectedthroughSerialBroadband2interface.
ON
ON
OFF
OFF
PCMcircuits64111areconnectedthrough
SerialBroadband2interface.
DN70630644
123
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table92
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
Switch
Function
OFF
OFF
ON
OFF
PCMcircuits64127areconnectedthrough
SerialBroadband2interface.
ON
OFF
ON
OFF
PCMcircuits64143areconnectedthrough
SerialBroadband2interface.
OFF
ON
ON
OFF
PCMcircuits64159areconnectedthrough
SerialBroadband2interface.
ON
ON
ON
OFF
PCMcircuits64175areconnectedthrough
SerialBroadband2interface.
OFF
OFF
OFF
ON
PCMcircuits64191areconnectedthrough
SerialBroadband2interface.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table93
124
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).
Switch
Function
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits128143areconnectedthrough
SerialBroadband3interface.
OFF
ON
OFF
OFF
PCMcircuits128159areconnectedthrough
SerialBroadband3interface.
ON
ON
OFF
OFF
PCMcircuits128175areconnectedthrough
SerialBroadband3interface.
OFF
OFF
ON
OFF
PCMcircuits128191areconnectedthrough
SerialBroadband3interface.
ON
OFF
ON
OFF
PCMcircuits128207areconnectedthrough
SerialBroadband3interface.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table93
SW256BC109365
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
Switch
Function
OFF
ON
ON
OFF
PCMcircuits128223areconnectedthrough
SerialBroadband3interface.
ON
ON
ON
OFF
PCMcircuits128239areconnectedthrough
SerialBroadband3interface.
OFF
OFF
OFF
ON
PCMcircuits128255areconnectedthrough
SerialBroadband3interface.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table94
Issue:2-9
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).
Switch
Function
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
ON
OFF
OFF
OFF
PCMcircuits192207areconnectedthrough
SerialBroadband4interface.
OFF
ON
OFF
OFF
PCMcircuits192223areconnectedthrough
SerialBroadband4interface.
ON
ON
OFF
OFF
PCMcircuits192239areconnectedthrough
SerialBroadband4interface.
OFF
OFF
ON
OFF
PCMcircuits192255areconnectedthrough
SerialBroadband4interface.
ON
OFF
ON
OFF
Notspecified
OFF
ON
ON
OFF
Notspecified
ON
ON
ON
OFF
Notspecified
OFF
OFF
OFF
ON
Notspecified
DN70630644
125
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BjumpersettingsinS15newdeliveryFlexiBSC
ThejumpersettingoftheSW256BinS15newdeliveryFlexiBSCispresentedinthe
tablesbelow.
Table95
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW1)
SW1
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
PCM0-2554M
modeselected
SW256B1
02
ON
ON
OFF
OFF
PCM256-5118M
modeselected
SW256B2
03
ON
ON
OFF
OFF
PCM512-7678M
modeselected
SW256B3
04
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
05
ON
ON
OFF
OFF
PCM1024-1279
8Mmodeselected
SW256B5
06
ON
ON
OFF
OFF
PCM1280-1535
8Mmodeselected
SW256B6
07
ON
ON
OFF
OFF
PCM1536-1791
8Mmodeselected
SW256B7
08
ON
ON
OFF
OFF
PCM1792-2047
8Mmodeselected
Table96
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW3)
SW3
126
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB1interfaceis
disabled
SW256B1
02
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits256319connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table96
SW256BC109365
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW3)
(Cont.)
SW3
Switch
A.SelectedifSB1
interfacesofETS2/ETIP1-AinETC
0&2slot21connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot14connected.
C.SelectedifSB2
interfaceofETP(T)/(E)inETC
0&2slot20isconnected.
D.SelectedifSB2
interfaceofETP(T)/(E)inGTIC0
slot30isconnected.
SW256B2
03
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits512575connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot17
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot13connected.
C.SelectedifSB2
interfaceofETP(T)/(E)inGTIC
0&1slot17isconnected.
Issue:2-9
DN70630644
127
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table96
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW3)
(Cont.)
SW3
Switch
D.SelectedifSB2
interfaceofETP(T)/(E)inGTIC0
slot26isconnected.
SW256B3
04
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits768831connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot15
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot11connected.
C.SelectedifSB2
interfaceofETP(T)/(E)inETC
1&3slot30isconnected.
D.SelectedifSB2
interfaceofETP(T)/(E)inGTIC1
slot30isconnected.
SW256B4
05
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits10241087connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot16
connected.
128
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table96
SW256BC109365
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW3)
(Cont.)
SW3
Switch
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot12connected.
C.SelectedifSB2
interfaceofETP(T)/(E)inETC
0&2slot23isconnected.
D.SelectedifSB2
interfaceofETP(T)/(E)inETC1
slot23isconnected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits12801343connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot13
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot13connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits15361599connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot11
connected.
Issue:2-9
DN70630644
129
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table96
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW3)
(Cont.)
SW3
Switch
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot12connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB1interface,
PCMcircuits17921855connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot12
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot12connected.
*)IfneitherETS2norETIP1-AnorETP(T)/(E)isconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyETS2/ETIP1-Aisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.HWredundancyETP(ETP(T)/(E))isinuse.
D.TransmissionredundancyETP(ETP(T)/(E))isinuse.
Table97
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW4)
SW4
SW256B0
130
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits64-127connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table97
SW256BC109365
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW4)
(Cont.)
SW4
Switch
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC
0&1slot10connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC
0slot10connected.
C.SelectedifSB2interfaceofETP(T)/(E)
inETC0&2slot26is
connected.
D.SelectedifSB2interfaceofETP(T)/(E)
inETC2slot26is
connected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits320-383connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinETC
0&2slot21connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot14connected.
SW256B2
03
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits576-639connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot17connected.
Issue:2-9
DN70630644
131
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table97
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW4)
(Cont.)
SW4
Switch
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
1slot13connected.
C.SelectedifSB2interfaceofETP(T)/(E)
inGTIC0&1slot17is
connected.
SW256B3
04
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits832-895connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot15connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
1slot11connected.
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1088-1151
connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot16connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
1slot12connected.
SW256B5
132
06
OFF
OFF
DN70630644
ON*)
OFF
SB2interface,PCM
circuits1344-1407
connected.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table97
SW256BC109365
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW4)
(Cont.)
SW4
Switch
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
0&1slot13connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot13connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1600-1663
connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
0&1slot11connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot11connected.
C.SelectedifSB2interfaceofETP(T)/(E)
inGTIC0&1slot15is
connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1856-1919
connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
0&1slot12connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot12connected.
Issue:2-9
DN70630644
133
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table97
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW4)
(Cont.)
SW4
Switch
*)IfneitherETS2norETIP1-AnorETP(T)/(E)isconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyETS2/ETIP1-Aisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.HWredundancyETP(ETP(T)/(E))isinuse.
D.TransmissionredundancyETP(ETP(T)/(E))isinuse.
Table98
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW5)
SW5
134
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B4
05
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B5
06
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B6
07
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B7
08
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1920-1983connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table98
SW256BC109365
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW5)
(Cont.)
SW5
Switch
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot14
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot10connected.
*)IfneitherETS2norETIP1-AnorETP(T)/(E)isconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyETS2/ETIP1-Aisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.HWredundancyETP(ETP(T)/(E))isinuse.
D.TransmissionredundancyETP(ETP(T)/(E))isinuse.
Table99
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW6)
SW6
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits
192-255connected.
A.SelectedifSB2interfacesofETS2/ETIP1-Ain
GTIC0&1slot10connected.
B.SelectedifSB2interfacesofETS2/ETIP1-Ain
GTIC0slot10connected.
Issue:2-9
SW256B1
02
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B2
03
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
DN70630644
135
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table99
JumpersettingoftheSW256BinS15newdeliveryFlexiBSC(SW6)
(Cont.)
SW6
Switch
SW256B4
05
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B5
06
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B6
07
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits
1984-2047connected.
A.SelectedifSB2interfacesofETS2/ETIP1-Ain
GTIC1&0slot14connected.
B.SelectedifSB2interfaceofETS2/ETIP1-Ain
GTIC1slot10connected.
C.SelectedifSB2interfaceofETP(T)/(E)inGTIC
0&1slot15isconnected.
D.SelectedifSB2interfaceofETP(T)/(E)inETC
0slot23isconnected.
*)IfneitherETS2norETIP1-AnorETP(T)/(E)isconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyETS2/ETIP1-Aisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.HWredundancyETP(ETP(T)/(E))isinuse.
D.TransmissionredundancyETP(ETP(T)/(E))isinuse.
SW256BjumpersettingsinS14first-deliveryFlexiBSC
Thefollowinginformationisspecificallyforfirst-deliveryFlexiBSCnetworkelements.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
136
4M/8MmodeforserialbusesR0...R31,T0...T31
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
4M/8MmodeforserialbusesR32...R63,T32...T63
SW1
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected
SW256B1
ON
ON
OFF
OFF
PCM256-5118Mmode
selected
SW256B2
ON
ON
OFF
OFF
PCM512-7678M
modeselected
SW256B3
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
ON
ON
OFF
OFF
PCM1024-12798M
modeselected
SW256B5
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
SW256B7
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW3
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note!
SW256B0
OFF
OFF
OFF
OFF
SB1interfaceisdisabled
SW256B1
OFF
OFF
OFF
OFF
SB1interfaceisdisabled
SW256B2
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits512-575connected.
DN70630644
137
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW3
Switch
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot17
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot13connected.
SW256B3
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits768-831connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot15
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot11connected.
SW256B4
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1024-1087connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot16
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot12connected.
SW256B5
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1280-1343connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC0&1slot13
connected.
138
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW3
SW256BC109365
Switch
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot13connected.
SW256B6
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1536-1599connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC0&1slot11
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot11connected.
SW256B7
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1792-1855connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC0&1slot12
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot12connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW4
Switch
Slot
Issue:2-9
1(1-8)
2(2-7)
DN70630644
3(3-6)
4(4-5)
Note
139
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
SW256B0
Switch
1
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits64-127connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot10connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot10
connected.
SW256B1
OFF
OFF
OFF
OFF
SB2interfaceisdisabled
SW256B2
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits576-639connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot17connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot13
connected.
SW256B3
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits832-895connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot15connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot11
connected.
SW256B4
140
OFF
OFF
DN70630644
ON*)
OFF
SB2interface,PCMcircuits1088-1151connected.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
SW256BC109365
Switch
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot16connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot12
connected.
SW256B5
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1344-1407connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot13connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot13
connected.
SW256B6
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1600-1663connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot11connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot11
connected.
SW256B7
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1856-1919connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot12connected.
Issue:2-9
DN70630644
141
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
Switch
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot12
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW5
142
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B1
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B2
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B3
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B4
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B5
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B6
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B7
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1920-1983connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW5
SW256BC109365
Switch
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot14connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot10
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW6
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits192-255connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot10connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
slot10connected.
Issue:2-9
SW256B1
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B2
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B3
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
DN70630644
143
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW6
Switch
SW256B4
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B5
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B6
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B7
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1984-2047connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot14connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot10
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SW256BjumpersettingsincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC
ThejumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhereBSCpart
isS15newdeliveryFlexiBSCispresentedinthetablesbelow.
Table100
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW1)
SW1
SW256B0
144
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table100
SW256BC109365
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW1)(Cont.)
SW1
Switch
SW256B1
02
ON
ON
OFF
OFF
PCM256-5118Mmode
selected.
SW256B2
03
ON
ON
OFF
OFF
PCM512-7678Mmode
selected.
SW256B3
04
ON
ON
OFF
OFF
PCM768-10238M
modeselected.
SW256B4
05
ON
ON
OFF
OFF
PCM1024-12798M
modeselected.
SW256B5
06
ON
ON
OFF
OFF
PCM1280-15358M
modeselected.
SW256B6
07
ON
ON
OFF
OFF
PCM1536-17918M
modeselected.
SW256B7
08
ON
ON
OFF
OFF
PCM1792-20478M
modeselected.
Table101
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW3)
SW3
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB1interfaceisdisabled
SW256B1
02
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits256-319connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinETC0
&2slot21connected.
Issue:2-9
DN70630644
145
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table101
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW3)(Cont.)
SW3
Switch
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot14connected.
C.SelectedifSB2interfaceofETPT/Ein
ETC0&2slot20is
connected.
SW256B2
03
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits512-575connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot17connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot13connected.
SW256B3
04
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits768-831connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot15connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot11connected.
C.SelectedifSB2interfaceofETPT/Ein
ETC1&3slot30is
connected.
SW256B4
146
05
OFF
OFF
DN70630644
ON*)
OFF
SB1interface,PCM
circuits1024-1087
connected.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table101
SW256BC109365
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW3)(Cont.)
SW3
Switch
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot16connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot12connected.
C.SelectedifSB2interfaceofETPT/Ein
ETC0&2slot23is
connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits1280-1343
connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot13connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot13connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits1536-1599
connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot11connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot11connected.
SW256B7
Issue:2-9
08
OFF
OFF
DN70630644
ON*)
OFF
SB1interface,PCM
circuits1792-1855
connected.
147
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table101
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW3)(Cont.)
SW3
Switch
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot12connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot12connected.
*)IfneitherETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
Table102
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW4)
SW4
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits64-127connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC
0&1slot10connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC
0slot10connected.
SW256B1
148
02
OFF
OFF
DN70630644
ON*)
OFF
SB2interface,PCM
circuits320-383connected.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table102
SW256BC109365
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW4)(Cont.)
SW4
Switch
A.SelectedifSB2interfacesofETS2/ETIP1-AinETC0
&2slot21connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot14connected.
C.SelectedifSB3
interfaceofETPT/E
inETC0&2slot20
connected.
SW256B2
03
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits576-639connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot17connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
1slot13connected.
SW256B3
04
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits832-895connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot15connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
1slot11connected.
Issue:2-9
DN70630644
149
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table102
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW4)(Cont.)
SW4
Switch
C.SelectedifSB3
interfaceofETPT/E
inETC1&3slot30
connected.
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1088-1151
connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot16connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
1slot12connected.
C.SelectedifSB3
interfaceofETPT/E
inETC0&2slot23
connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1344-1407
connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot13connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot13connected.
SW256B6
150
07
OFF
OFF
DN70630644
ON*)
OFF
SB2interface,PCM
circuits1600-1663
connected.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table102
SW256BC109365
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW4)(Cont.)
SW4
Switch
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
1&0slot11connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot11connected.
C.SelectedifSB2
interfaceofETPT/E
inGTIC0&1slot15
isconnected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1856-1919
connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC
0&1slot12connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC
0slot12connected.
C.SelectedifSB2interfaceofETPT/Ein
GTIC0&1slot17is
connected.
1)IfneitherETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
Issue:2-9
DN70630644
151
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table103
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW5)
SW5
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B4
05
ON**)
ON**)
OFF
OFF
SB3interface,PCM
circuits1152-1199
connectedtoSBMUX-Ainslot01of
GTIC8>IC9
(TC2C2)
SW256B5
06
ON**)
ON**)
OFF
OFF
SB3interface,PCM
circuits1408-1455
connectedtoSBMUX-Ainslot01of
GTIC5>IC6
(TC2C1)
SW256B6
07
ON**)
ON**)
OFF
OFF
SB3interface,PCM
circuits1664-1711
connectedtoSBMUX-Ainslot01of
GTIC2>IC3
(TC2C0)
SW256B7
08
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1920-1983
connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-AinGTIC
1&0slot14connected.
152
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table103
SW256BC109365
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW5)(Cont.)
SW5
Switch
B.SelectedifSB1
interfaceofETS2/ETIP1-AinGTIC
1slot10connected.
*)IfneitherETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmustbe
OFF.
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF.
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunitsis
used.
Table104
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW6)
SW6
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits192-255connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-AinGTIC
0&1slot10connected.
B.SelectedifSB2
interfacesofETS2/ETIP1-AinGTIC
0slot10connected.
C.SelectedifSB3
interfaceofETPT/E
inETC0&2slot26
isconnected.
SW256B1
Issue:2-9
02
OFF
OFF
DN70630644
OFF
OFF
SB4interfaceisdisabled.
153
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table104
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW6)(Cont.)
SW6
Switch
SW256B2
03
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B4
05
ON**)
ON**)
OFF
OFF
SB4interface,PCM
circuits1216-1263
connectedtoSBMUX-Ainslot02of
GTIC8>IC9
(TC2C2).
SW256B5
06
ON**)
ON**)
OFF
OFF
SB4interface,PCM
circuits1472-1519
connectedtoSBMUX-Ainslot02of
GTIC5>IC6
(TC2C1).
SW256B6
07
ON**)
ON**)
OFF
OFF
SB4interface,PCM
circuits1728-1775
connectedtoSBMUX-Ainslot02of
GTIC2>IC3
(TC2C0).
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1984-2047
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-AinGTIC
1&0slot14connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-AinGTIC
1slot10connected.
*)IfneitherETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmustbe
OFF.
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF.
A.HWredundancyisinuse.
154
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table104
SW256BC109365
JumpersettingoftheSW256BincombinedBSC/TCSMinstallationwhere
BSCpartisS15newdeliveryFlexiBSC(SW6)(Cont.)
SW6
Switch
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SW256BjumpersettingsincombinedBSC/TCSMinstallationwhere
theBSCpartisS14first-deliveryFlexiBSC
ThefollowinginformationisspecificallyforcombinedBSC/TCSMinstallationswherethe
BSCpartisfirst-deliveryFlexiBSC.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
SW1
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected
SW256B1
ON
ON
OFF
OFF
PCM256-5118Mmode
selected
SW256B2
ON
ON
OFF
OFF
PCM512-7678Mmode
selected
SW256B3
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
ON
ON
OFF
OFF
PCM1024-12798M
modeselected
SW256B5
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
DN70630644
155
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW1
SW256B7
Switch
8
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW3
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
OFF
OFF
OFF
OFF
SB1interfaceisdisabled
SW256B1
OFF
OFF
OFF
OFF
SB1interfaceisdisabled
SW256B2
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits512-575connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot17
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot13connected.
SW256B3
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits768-831connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot15
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot11connected.
156
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW3
SW256B4
SW256BC109365
Switch
5
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1024-1087connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC1&0slot16
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot12connected.
SW256B5
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1280-1343connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC0&1slot13
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot13connected.
SW256B6
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1536-1599connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC0&1slot11
connected.
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot11connected.
SW256B7
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1792-1855connected.
A.SelectedifSB1interfacesofETS2/ETIP1-A
inGTIC0&1slot12
connected.
Issue:2-9
DN70630644
157
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW3
Switch
B.SelectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot12connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW4
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits64-127connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot10connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot10
connected.
SW256B1
OFF
OFF
OFF
OFF
SB2interfaceisdisabled
SW256B2
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits576-639connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot17connected.
158
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
SW256BC109365
Switch
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot13
connected.
SW256B3
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits832-895connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot15connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot11
connected.
SW256B4
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1088-1151connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot16connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot12
connected.
SW256B5
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1344-1407connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot13connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot13
connected.
SW256B6
Issue:2-9
OFF
OFF
DN70630644
ON*)
OFF
SB2interface,PCMcircuits1600-1663connected.
159
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
Switch
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot11connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot11
connected..
SW256B7
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1856-1919connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot12connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot12
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW5
160
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B1
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B2
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW5
SW256BC109365
Switch
SW256B3
OFF
OFF
OFF
OFF
SB3interfaceisdisabled
SW256B4
ON**)
ON**)
OFF
OFF
SB3interface,PCMcircuits1152-1199connectedtoSBMUX-Ain
slot01ofGTIC8&
GTIC9(TC2C2)
SW256B5
ON**)
ON**)
OFF
OFF
SB3interface,PCMcircuits1408-1455connectedtoSBMUX-Ain
slot01ofGTIC5&
GTIC6(TC2C1)
SW256B6
ON**)
ON**)
OFF
OFF
SB3interface,PCMcircuits1664-1711connectedtoSBMUX-Ain
slot01ofGTIC2&
GTIC3(TC2C0)
SW256B7
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1920-1983connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot14connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot10
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Issue:2-9
DN70630644
161
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW6
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note!
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits192-255connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot10connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot10
connected.
162
SW256B1
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B2
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B3
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B4
ON**)
ON**)
OFF
OFF
SB4interface,PCMcircuits1216-1263connectedtoSBMUX-Ain
slot02ofGTIC8&
GTIC9(TC2C2)
SW256B5
ON**)
ON**)
OFF
OFF
SB4interface,PCMcircuits1472-1519connectedtoSBMUX-Ain
slot02ofGTIC5&
GTIC6(TC2C1)
SW256B6
ON**)
ON**)
OFF
OFF
SB4interface,PCMcircuits1728-1775connectedtoSBMUX-Ain
slot02ofGTIC2&
GTIC3(TC2C0)
SW256B7
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1984-2047connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW6
SW256BC109365
Switch
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot14connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot10
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
SW256BjumpersettingsinupgradedFlexiBSC
ThefollowinginformationisspecificallyforupgradedFlexiBSCnetworkelements.Note
thatinupgradedFlexiBSC,SerialBroadband1(SB1)interfacesarenotusedatallin
GSW2KB0&1slots02-07.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
SW1
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
OFF
OFF
OFF
OFF
PCM0-2554M
modeselected
SW256B1
OFF
OFF
OFF
OFF
PCM256-5114M
modeselected
SW256B2
ON
ON
OFF
OFF
PCM512-7678M
modeselected
DN70630644
163
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW1
Switch
SW256B3
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
ON
ON
OFF
OFF
PCM1024-12798M
modeselected
SW256B5
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
SW256B7
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW3
164
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
SW256B4
05
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
SW256B5
06
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
SW256B6
07
OFF
OFF
OFF
OFF
SB1interfaceis
disabled.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SW3
SW256B7
Switch
08
OFF
OFF
OFF*)
OFF
SB1interface,PCM
circuits1792-1855
connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot07
connected.
B.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1slot03connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot05connected.
D.SelectedifSB3
interfaceofETPT/E
inGTIC0&1slot
07isconnected.
*)IfneitherETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmust
beOFF.
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW4
SW256B0
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits64-127connected.
DN70630644
165
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
Switch
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot01
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot01connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot01connected.
D.SelectedifSB2
interfaceofETPT/E
inETC4&5slot
02isconnected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits320-383
connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot02
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot02connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot03connected.
D.SelectedifSB2
interfaceofETPT/E
inGTIC0&1slot
02isconnected.
SW256B2
166
03
OFF
OFF
DN70630644
OFF
OFF
SB2interfaceis
disabled.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SW4
Switch
SW256B3
04
OFF
OFF
OFF
OFF
SB2interfaceis
disabled.
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1088-1151
connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot03
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot03connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot05connected.
D.SelectedifSB2
interfaceofETPT/E
inETC4&5slot
07isconnected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1344-1407
connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot05
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC1slot01connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot01connected.
Issue:2-9
DN70630644
167
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW4
Switch
D.SelectedifSB3
interfaceofETPT/E
inETC2&3slot
02isconnected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1600-1663
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC1&0slot05
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC1slot01connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot02connected.
D.SelectedifSB2
interfaceofETPT/E
inETC2&3slot
02isconnected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1856-1919
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC1&0slot07
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC1slot03connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot06connected.
168
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SW4
Switch
D.SelectedifSB2
interfaceofETPT/E
inGTIC0&1slot
07isconnected.
*)IfnorETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmustbe
OFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW5
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceis
disabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceis
disabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceis
disabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceis
disabled.
SW256B4
05
OFF
OFF
OFF
OFF
SB3interfaceis
disabled.
SW256B5
06
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1408-1471
connected.
DN70630644
169
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW5
Switch
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC0&1slot04
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot04connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot07connected.
D.SelectedifSB1
interfaceofETPT/E
inGTIC0&1slot
04isconnected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1664-1727
connected.
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot06
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot02connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot03connected.
D.SelectedifSB2
interfaceofETPT/E
inETC2&3slot
07isconnected.
SW256B7
170
08
OFF
OFF
DN70630644
ON*)
OFF
SB3interface,PCM
circuits1920-1983
connected.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SW5
Switch
A.SelectedifSB1
interfacesofETS2/ETIP1-Ain
GTIC1&0slot08
connected.
B.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot04connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot07connected.
D.SelectedifSB1
interfaceofETPT/E
inGTIC0&1slot
08isconnected.
*)IfnorETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmustbe
OFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
SW6
SW256B0
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits192-255
connected.
DN70630644
171
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW6
Switch
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC0&1slot01
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC0slot01connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot02connected.
D.SelectedifSB3
interfaceofETPT/E
inETC4&5slot
02isconnected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits448-511
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC0&1slot02
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC0slot02connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot04connected.
D.SelectedifSB3
interfaceofETPT/E
inGTIC0&1slot
02isconnected.
SW256B2
172
03
OFF
OFF
DN70630644
OFF
OFF
SB4interfaceis
disabled.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SW6
Switch
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceis
disabled.
SW256B4
05
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1216-1279
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC0&1slot03
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC0slot03connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot06connected.
D.SelectedifSB3
interfaceofETPT/E
inETC4&5slot
07isconnected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1472-1535
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC0&1slot04
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC0slot04connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC0slot08connected.
Issue:2-9
DN70630644
173
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW6
Switch
D.SelectedifSB2
interfaceofETPT/E
inGTIC0&1slot
04isconnected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1728-1791
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC1&0slot06
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC1slot02connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot04connected.
D.SelectedifSB3
interfaceofETPT/E
inETC2&3slot
07isconnected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1984-2047
connected.
A.SelectedifSB2
interfacesofETS2/ETIP1-Ain
GTIC1&0slot08
connected.
B.SelectedifSB2
interfaceofETS2/ETIP1-Ain
GTIC1slot04connected.
C.SelectedifSB1
interfaceofETS2/ETIP1-Ain
GTIC1slot08connected.
174
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SW6
Switch
D.SelectedifSB2
interfaceofETPT/E
inGTIC0&1slot
08isconnected.
*)IfnorETS2norETIP1-AnorETPT/EisconnectedinthisPCMposition,switchmustbe
OFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SW256BsettingsinacombinedBSC/TCSMinstallationwherethe
BSCpartisupgradedFlexiBSC
ThefollowinginformationisspecificallyforacombinedBSC/TCSMinstallationwherethe
BSCpartisupgradedFlexiBSC.NotethatinupgradedFlexiBSC,SerialBroadband1
(SB1)interfacesarenotusedatallinGSW2KB0&1slots02-07.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
Table105
PCMmodesettingsontheSW256B(SW1).
SW1
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected
SW256B1
02
OFF
OFF
OFF
OFF
PCM256-5114Mmode
selected
SW256B2
03
ON
ON
OFF
OFF
PCM512-7678M
modeselected
SW256B3
04
ON
ON
OFF
OFF
PCM768-10238M
modeselected
DN70630644
175
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table105
PCMmodesettingsontheSW256B(SW1).(Cont.)
SW1
Switch
SW256B4
05
ON
ON
OFF
OFF
PCM1024-12798M
modeselected
SW256B5
06
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
07
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
SW256B7
08
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table106
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).
SW3
176
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B3
04
OFF**)
OFF**)
OFF
OFF
SB1interface,PCMcircuits768-815connectedtoSBMUX-Ainslot
01ofGTIC5>IC6
(TC2C1)
SW256B4
05
OFF**)
OFF**)
OFF
OFF
SB1interface,PCMcircuits1024-1071connectedtoSBMUX-Ain
slot01ofGTIC8&
GTIC9(TC2C2)
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table106
SW256BC109365
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
SW3
Switch
SW256B5
06
OFF**)
OFF**)
OFF
OFF
SB1interface,PCMcircuits1280-1327connectedtoSBMUX-Ain
slot01ofGTIC2&
GTIC3(TC2C0)
SW256B6
07
OFF**)
OFF**)
OFF
OFF
SB1interface,PCMcircuits1536-1583connectedtoSBMUX-Ain
slot02ofGTIC2&
GTIC3(TC2C0)
SW256B7
08
OFF
OFF
OFF*)
OFF
SB1interface,PCMcircuits1792-1855connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot07connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot03
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot05
connected.
D.SelectedifSB3interfaceofETPT/Ein
GTIC0&1slot07is
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Issue:2-9
DN70630644
177
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table107
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).
SW4
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits64-127connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot01connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot01
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot01
connected.
D.SelectedifSB2interfaceofETPT/EinETC
4&5slot02isconnected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits320-383connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot02connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot02
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot03
connected.
D.SelectedifSB2interfaceofETPT/Ein
GTIC0&1slot02is
connected.
SW256B2
178
03
OFF
OFF
DN70630644
OFF
OFF
SB2interfaceisdisabled.
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table107
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
SW256B3
04
ON**)
ON**)
OFF
OFF
SB2interface,PCMcircuits832-879connectedtoSBMUX-Ainslot
02ofGTIC5>IC6
(TC2C1)
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1088-1151connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot03
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot05
connected.
D.SelectedifSB2interfaceofETPT/Ein
ETC4&5slot07is
connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1344-1407connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot05connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot01
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot01
connected.
D.SelectedifSB3interfaceofETPT/Ein
ETC2&3slot02is
connected.
Issue:2-9
DN70630644
179
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table107
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
SW256B6
Switch
07
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1600-1663connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot05connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot01
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot02
connected.
D.SelectedifSB2interfaceofETPT/Ein
ETC2&3slot02is
connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1856-1919connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot07connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot03
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot06
connected.
D.SelectedifSB2interfaceofETPT/Ein
GTIC0&1slot07is
connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
180
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table107
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table108
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).
SW5
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B4
05
ON**)
ON**)
OFF
OFF
SB3interface,PCMcircuits1152-1199connectedtoSBMUX-Ain
slot02ofGTIC8&
GTIC9(TC2C2)
SW256B5
06
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1408-1471connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
Issue:2-9
DN70630644
181
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table108
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
Switch
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot04
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot07
connected.
D.SelectedifSB1interfaceofETPT/Ein
GTIC0&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1664-1727connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot02
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot03
connected.
D.SelectedifSB1interfaceofETPT/Ein
ETC2&3slot07connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1920-1983connected.
A.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot04
connected.
182
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table108
SW256BC109365
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
Switch
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot07
connected.
D.SelectedifSB1interfaceofETPT/Ein
GTIC0&1slot08connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF
**)IfSBMUX-AisnotconnectedinthisPCMposition,switchmustbeOFF
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table109
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).
Switch
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
01
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits192-255connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot01connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot01
connected.
Issue:2-9
DN70630644
183
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table109
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot02
connected.
D.SelectedifSB3interfaceofETPT/Ein
ETC4&5slot02connected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits448-511connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot02connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot02
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot04
connected.
D.SelectedifSB3interfaceofETPT/Ein
GTIC0&1slot02connected.
SW256B2
03
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceisdisabled
SW256B4
05
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1216-1279connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
184
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table109
SW256BC109365
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot03
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot06
connected.
D.SelectedifSB3interfaceofETPT/Ein
ETC4&5slot07connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1472-1535connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot04
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot08
connected.
D.SelectedifSB2interfaceofETPT/Ein
GTIC0&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1728-1791connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot02
connected.
Issue:2-9
DN70630644
185
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table109
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot04
connected.
D.SelectedifSB3interfaceofETPT/Ein
ETC2&3slot07connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1984-2047connected.
A.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot04
connected.
C.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot08
connected.
D.SelectedifSB2interfaceofETPT/Ein
GTIC0&1slot08connected.
*)IfETS2orETIP1-AisnotconnectedinthisPCMposition,switchmustbeOFF.
A.HWredundancyisinuse.
B.TransmissionredundancyisinuseandfullcapacityofETS2and/orETIP1-Aplug-inunits
isused.
C.TransmissionredundancyisinuseandhalfcapacityofETS2and/orETIP1-Aplug-in
unitsisused.
SW256BjumpersettingsinBSC3i
ThefollowinginformationisspecificallyforBSC3inetworkelements.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
186
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
Table110
PCMmodesettingsontheSW256B(SW1).
SW1
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected
SW256B1
02
OFF
OFF
OFF
OFF
PCM256-5114Mmode
selected
SW256B2
03
ON
ON
OFF
OFF
PCM512-7678M
modeselected
SW256B3
04
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
05
OFF
OFF
OFF
OFF
PCM1024-12794M
modeselected
SW256B5
06
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
07
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
SW256B7
08
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table111
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).
SW3
SW256B0
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
DN70630644
187
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table111
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
SW3
Switch
SW256B1
02
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B4
05
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B5
06
ON
ON
OFF
OFF
SB1interfaceisdisabled.
SW256B6
07
ON
ON
OFF
OFF
SB1interfaceisdisabled.
SW256B7
08
OFF
OFF
ON*)
OFF
SB1interface,PCMcircuits1792-1855connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot03
connectedorSB1interfaceofETS2/ETIP1-A
inGTIC1slot05connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1&0slot07
connected.
C.SelectedifSB3interfaceofETPE/Tin
slot6ofGTIC-0(for
BSC3i1000)connectedorselectedifSB3
interfaceofETPE/Tin
slot1ofETC-5(for
BSC3i2000)connected.
D.SelectedifSB3interfaceofETPE/Tin
slot6ofGTIC0/GTIC1
connected.
188
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table111
SW256BC109365
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
SW3
Switch
*)IfETS2orETIP1-AorETPEorETPTisnotconnectedinthisPCMposition,switchmust
beOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table112
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).
SW4
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits64-127connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot01
connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0&1slot01
connected.
C.SelectedifSB2interfaceofETPE/Tin
slot1ofETC-4(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot1ofETC-4/ETC-5
(forBSC3i2000)connected.
Issue:2-9
DN70630644
189
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table112
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
SW256B1
Switch
02
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits320-383connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot02
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot03connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0&1slot02
connected.
C.SelectedifSB2interfaceofETPE/Tin
slot1ofGTIC-0(for
BSC1000)orselected
ifSB2interfaceof
ETPE/Tinslot6of
ETC-3(forBSC2000).
D.SelectedifSB2interfaceofETPE/Tin
slot1ofGTIC0/GTIC1
connected.
E.SelectedifSB2interfaceofETP(A)in
slot3ofETC-4(for
BSC3i2000)connected.
SW256B2
03
OFF
OFF
OFF
OFF
SB2interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB2interfaceisdisabled.
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1088-1151connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot03
connectedorselected
190
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table112
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot05connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
C.SelectedifSB2interfaceofETPE/Tin
slot6ofETC-4(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot6ofETC4/ETC5
connected.
E.SelectedifSB2interfaceofETP(A)in
slot3ofGTIC-0(for
BSC3i1000)connectedorselectedifSB2
interfaceofETP(A)in
slot3ofETC-2(for
BSC3i2000)connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1344-1407connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot01
connected.
B.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1&0slot05
connected.
C.SelectedifSB3interfaceofETPE/Tin
slot6ofETC-5(for
BSC3i2000)connected.
Issue:2-9
DN70630644
191
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table112
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
D.SelectedifSB3interfaceofETPE/Tin
slot1ofETC2/ETC3
connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1600-1663connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot01
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC1
slot02connected.
B.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1&0slot05
connected.
C.SelectedifSB2interfaceofETPE/Tin
slot6ofETC-5(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot1ofETC2/ETC3
connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB2interface,PCMcircuits1856-1919connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot03
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC1
slot06connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot07connected.
192
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table112
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
C.SelectedifSB2interfacesofETPE/Tin
track6ofGTIC-0(for
BSC3i1000)orselectedifSB2interfacesof
ETPE/Tintrack1of
ETC-5(forBSC3i
2000).
D.SelectedifSB2interfaceofETPE/Tin
track6ofGTIC0/GTIC
1connected.
*)IfETS2orETIP1-AorETPEorETPTorETP(A)isnotconnectedinthisPCMposition,
switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
E.ETP(A)poolredundancyinuse.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table113
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).
SW5
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
DN70630644
193
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table113
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
Switch
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B4
05
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B5
06
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1408-1471connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC0slot04
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot07connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1664-1727connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot02
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC1
slot03connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
C.SelectedifSB2interfacesofETPE/Tin
track6ofETC-2(for
BSC3i2000).
D.SelectedifSB2interfaceofETPE/Tin
track6ETC-2/ETC-3
connected(forBSC3i
2000).
194
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table113
SW256BC109365
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
SW256B7
Switch
08
OFF
OFF
ON*)
OFF
SB3interface,PCMcircuits1920-1983connected.
A.SelectedifSB1interfaceofETS2/ETIP1AinGTIC1slot04
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC1
slot07connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
*)IfETS2orETIP1-AorETPEorETPTisnotconnectedinthisPCMposition,switchmust
beOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table114
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).
Switch
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
01
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits192-255connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot01
connectedorselected
Issue:2-9
DN70630644
195
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table114
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot02connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot01connected.
C.SelectedifSB3interfacesofETPE/Tin
track1ofETC-4(for
BSC3i2000).
D.SelectedifSB3interfaceofETPE/Tin
track1ofETC5/ETC4
connected(forBSC3i
2000).
SW256B1
02
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits448-511connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot02
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot04connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot02connected.
C.SelectedifSB3interfacesofETPE/Tin
track1ofGTIC-0(for
BSC3i1000)orselectedifSB3interfacesof
ETPE/Tintrack6of
ETC-3(forBSC3i
2000).
D.SelectedifSB3interfaceofETPE/Tin
track1GTIC0/GTIC1
connected.
196
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table114
SW256BC109365
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
E.SelectedifSB2interfaceofETP(A)in
track3ofETC-5(for
BSC3i2000)connected.
SW256B2
03
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B4
05
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1216-1279connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot03
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot06connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
C.SelectedifSB3interfacesofETPE/Tin
track6ofETC-4(for
BSC3i2000).
D.SelectedifSB3interfaceofETPE/Tin
track6ofETC4/ETC5
connected(forBSC3i
2000).
E.SelectedifSB2interfaceofETP(A)in
track3ofGTIC-1(for
BSC3i1000)connectedorselectedifSB2
interfaceofETP(A)in
track3ofETC-3(for
BSC3i2000)connected.
Issue:2-9
DN70630644
197
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table114
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
SW256B5
Switch
06
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1472-1535connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC0slot04
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC0
slot08connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1728-1791connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot02
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC1
slot04connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
C.SelectedifSB3interfacesofETPE/Tin
track6ofETC-2(for
BSC3i2000).
D.SelectedifSB3interfacesofETPE/Tin
track6ofETC2/ETC3
connected(forBSC3i
2000).
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCMcircuits1984-2047connected.
A.SelectedifSB2interfaceofETS2/ETIP1AinGTIC1slot04
198
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table114
SW256BC109365
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
connectedorselected
ifSB1interfaceofETS2/ETIP1-AinGTIC1
slot08connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
*)IfETS2orETIP1-AorETPEorETPTorETP(A)isnotconnectedinthisPCMposition,
switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
E.ETP(A)poolredundancyinuse.
SW256settingsinacombinedBSC/TCSMinstallationwheretheBSC
partisBSC3i1000orBSC3i2000andTCSMpartisS12-S14HW
TCSM3i
ThefollowinginformationisspecificallyforcombinedBSC3i/TCSM3inetworkelement
installations,wheretheBSCpartisBSC3i1000orBSC3i2000andtheTCSMpartis
S12-S14HWTCSM3i.AlsomixedS12-S14HWTCSM3icabinetandS15HWTCSM3i
cabinetconfigurationsintheTCSMpartaresupported.ThesupportedTCSMpart
cabinetconfigurationsasfollows:
3xS12-S14HWTCSM3icabinets
2xS12-S14HWTCSM3icabinets+1xS15HWTCSM3icabinet
1xS12-S14HWTCSM3icabinet+2xS15HWTCSM3icabinets
2xS15HWTCSM3icabinets
S15HWTCSM3irelatedSW256BDIPswitchsettingsarepresentedinsectionSW256
settingsinacombinedBSC/TCSMinstallationwheretheBSCpartisBSC3i1000or
BSC3i2000andTCSMpartisS15HWTCSM3i.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
Issue:2-9
4M/8MmodeforserialbusesR0...R31,T0...T31
DN70630644
199
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
4M/8MmodeforserialbusesR32...R63,T32...T63
Table115
PCMmodesettingsontheSW256B(SW1).
SW1
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected
SW256B1
02
OFF
OFF
OFF
OFF
PCM256-5114M
modeselected
SW256B2
03
ON
ON
OFF
OFF
PCM512-7678M
modeselected
SW256B3
04
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
05
OFF
OFF
OFF
OFF
PCM1024-12794M
modeselected.Used
whenonlyTCSA0
cabinetisequipped.
05
ON1)
ON1)
OFF
OFF
PCM1024-12798M
modeselected.Used
whenTCSA1cabinet
orbothTCSA1and
TCSA2cabinetsare
equipped.
SW256B5
06
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
07
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
SW256B7
08
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
1)IfTCSA1andTCSA2cabinetsarenotequippedincombinedBSC/TCSMinstallation,
switchmustbeOFF.
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
200
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table116
SW256BC109365
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).
SW3
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B3
04
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits768-815connectedtoSBMUX-Ain
slot01ofGTIC5&
GTIC6(TCSA1).
SW256B4
05
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits1024-1071
connectedtoSBMUXAinslot01ofGTIC8
>IC9(TCSA2).
SW256B5
06
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits1280-1327
connectedtoSBMUXAinslot01ofGTIC2
>IC3(TCSA0).
SW256B6
07
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits1536-1583
connectedtoSBMUXAinslot02ofGTIC2
>IC3(TCSA0).
SW256B7
08
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits1792-1855
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot03connectedor
SB1interfaceofETS2/ETIP1-AinGTIC1
slot05connected.
Issue:2-9
DN70630644
201
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table116
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
SW3
Switch
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
&0slot07connected.
C.SelectedifSB3interfaceofETPE/Tin
slot6ofGTIC-0(for
BSC3i1000)connectedorselectedifSB3
interfaceofETPE/Tin
slot1ofETC-5(for
BSC3i2000)connected.
D.SelectedifSB3interfaceofETPE/Tin
slot6ofGTIC0/GTIC
1connected.
*)IfSBMUX-AorETS2orETIP1-AorETPEorETPTisnotconnectedinthisPCMposition,
switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table117
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).
SW4
SW256B0
202
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits64-127connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table117
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot01connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
&1slot01connected.
C.SelectedifSB2interfaceofETPE/Tin
slot1ofETC-4(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot1ofETC-4/ETC-5
(forBSC3i2000)connected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits320-383connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot03connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
&1slot02connected.
C.SelectedifSB2interfaceofETPE/Tin
slot1ofGTIC-0(for
BSC1000)orselected
ifSB2interfaceof
ETPE/Tinslot6of
ETC-3(forBSC2000).
D.SelectedifSB2interfaceofETPE/Tin
slot1ofGTIC0/GTIC
1connected.
Issue:2-9
DN70630644
203
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table117
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
E.SelectedifSB2interfaceofETP(A)in
slot3ofETC-4(for
BSC3i2000)connected.
SW256B2
03
OFF
OFF
OFF
OFF
SB2interfaceisdisabled.
SW256B3
04
ON*)
ON*)
OFF
OFF
SB2interface,PCM
circuits832-879connectedtoSBMUX-Ain
slot02ofGTIC5&
GTIC6(TCSA1).
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1088-1151
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot03connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot05connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
C.SelectedifSB2interfaceofETPE/Tin
slot6ofETC-4(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot6ofETC4/ETC5
connected.
E.SelectedifSB2interfaceofETP(A)in
slot3ofGTIC-0(for
BSC3i1000)connectedorselectedifSB2
interfaceofETP(A)in
204
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table117
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
slot3ofETC-2(for
BSC3i2000)connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1344-1407
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot01connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
&0slot05connected.
C.SelectedifSB3interfaceofETPE/Tin
slot6ofETC-5(for
BSC3i2000)connected.
D.SelectedifSB3interfaceofETPE/Tin
slot1ofETC2/ETC3
connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1600-1663
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot01connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot02connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
&0slot05connected.
C.SelectedifSB2interfaceofETPE/Tin
slot6ofETC-5(for
BSC3i2000)connected.
Issue:2-9
DN70630644
205
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table117
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
D.SelectedifSB2interfaceofETPE/Tin
slot1ofETC2/ETC3
connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1856-1919
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot03connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot06connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot07connected.
C.SelectedifSB2interfacesofETPE/Tin
track6ofGTIC-0(for
BSC3i1000)orselectedifSB2interfacesof
ETPE/Tintrack1of
ETC-5(forBSC3i
2000).
D.SelectedifSB2interfaceofETPE/Tin
track6ofGTIC
0/GTIC1connected.
*)IfSBMUX-AorETS2orETIP1-AorETPEorETPTorETP(A)isnotconnectedinthis
PCMposition,switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
E.ETP(A)poolredundancyinuse.
206
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table118
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).
SW5
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B4
05
ON*)
ON*)
OFF
OFF
SB3interface,PCM
circuits1152-1199
connectedtoSBMUXAinslot02ofGTIC8
>IC9(TCSA2).
SW256B5
06
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1408-1471
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot07connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1664-1727
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
Issue:2-9
DN70630644
207
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table118
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
Switch
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot03connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
C.SelectedifSB2interfacesofETPE/Tin
track6ofETC-2(for
BSC3i2000).
D.SelectedifSB2interfaceofETPE/Tin
track6ETC-2/ETC-3
connected(forBSC3i
2000).
SW256B7
08
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1920-1983
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot07connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
*)IfSBMUX-AorETS2orETIP1-AorETPEorETPTisnotconnectedinthisPCMposition,
switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
208
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table119
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).
Switch
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
01
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits192-255connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot01connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot02connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot01connected.
C.SelectedifSB3interfacesofETPE/Tin
track1ofETC-4(for
BSC3i2000).
D.SelectedifSB3interfaceofETPE/Tin
track1ofETC5/ETC4
connected(forBSC3i
2000).
SW256B1
02
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits448-511connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot04connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot02connected.
Issue:2-9
DN70630644
209
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table119
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
C.SelectedifSB3interfacesofETPE/Tin
track1ofGTIC-0(for
BSC3i1000)orselectedifSB3interfacesof
ETPE/Tintrack6of
ETC-3(forBSC3i
2000).
D.SelectedifSB3interfaceofETPE/Tin
track1GTIC0/GTIC1
connected.
E.SelectedifSB2interfaceofETP(A)in
track3ofETC-5(for
BSC3i2000)connected.
SW256B2
03
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B4
05
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1216-1279
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot03connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot06connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
C.SelectedifSB3interfacesofETPE/Tin
track6ofETC-4(for
BSC3i2000).
210
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table119
SW256BC109365
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
D.SelectedifSB3interfaceofETPE/Tin
track6ofETC4/ETC5
connected(forBSC3i
2000).
E.SelectedifSB2interfaceofETP(A)in
track3ofGTIC-1(for
BSC3i1000)connectedorselectedifSB2
interfaceofETP(A)in
track3ofETC-3(for
BSC3i2000)connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1472-1535
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot08connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1728-1791
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot04connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
Issue:2-9
DN70630644
211
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table119
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
C.SelectedifSB3interfacesofETPE/Tin
track6ofETC-2(for
BSC3i2000).
D.SelectedifSB3interfacesofETPE/Tin
track6ofETC2/ETC
3connected(for
BSC3i2000).
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1984-2047
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot08connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
*)IfETS2orETIP1-AorETPEorETPTorETP(A)isnotconnectedinthisPCMposition,
switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
E.ETP(A)poolredundancyinuse.
SW256settingsinacombinedBSC/TCSMinstallationwheretheBSC
partisBSC3i1000orBSC3i2000andTCSMpartisS15HWTCSM3i
ThefollowinginformationisspecificallyforcombinedBSC3i/TCSM3inetworkelement
installations,wheretheBSCpartisBSC3i1000orBSC3i2000andtheTCSMpartis
S15HWTCSM3i.AlsomixedS12-S14HWTCSM3icabinetandS15HWTCSM3i
cabinetconfigurationsintheTCSMpartaresupported.ThesupportedTCSMpart
cabinetconfigurationsasfollows:
212
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
SW256BC109365
3xS12-S14HWTCSM3icabinets
2xS12-S14HWTCSM3icabinets+1xS15HWTCSM3icabinet
1xS12-S14HWTCSM3icabinet+2xS15HWTCSM3icabinets
2xS15HWTCSM3icabinets
S12-S14HWTCSM3irelatedSW256BDIPswitchsettingsarepresentedinsection
SW256settingsinacombinedBSC/TCSMinstallationwheretheBSCpartisBSC3i
1000orBSC3i2000andTCSMpartisS12-S14HWTCSM3i.
TCSA1&TCSA2(onlywhenTCSA0isS12-S14HWTCSM3icabinet)cabinetsarein
useonlywhentheBSCpartisBSC3i1000.
PCMmodesettings(SW1)
ThePCMmodesetupismadewithmicroswitches:
4M/8MmodeforserialbusesR0...R31,T0...T31
4M/8MmodeforserialbusesR32...R63,T32...T63
Table120
PCMmodesettingsontheSW256B(SW1).
SW1
Issue:2-9
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
PCM0-2554Mmode
selected
SW256B1
02
OFF
OFF
OFF
OFF
PCM256-5114M
modeselected
SW256B2
03
ON
ON
OFF
OFF
PCM512-7678M
modeselected
SW256B3
04
ON
ON
OFF
OFF
PCM768-10238M
modeselected
SW256B4
05
OFF
OFF
OFF
OFF
PCM1024-12794M
modeselected.Used
whenonlyTCSA0
cabinetisequipped.
05
ON1)
ON1)
OFF
OFF
PCM1024-12798M
modeselected.Used
whenTCSA1cabinet
orbothTCSA1and
TCSA2cabinetsare
equipped.
DN70630644
213
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table120
PCMmodesettingsontheSW256B(SW1).(Cont.)
SW1
Switch
SW256B5
06
ON
ON
OFF
OFF
PCM1280-15358M
modeselected
SW256B6
07
ON
ON
OFF
OFF
PCM1536-17918M
modeselected
SW256B7
08
ON
ON
OFF
OFF
PCM1792-20478M
modeselected
1)IfTCSA1andTCSA2cabinetsarenotequippedincombinedBSC/TCSMinstallation,
switchmustbeOFF.
SerialBroadbandSB1settings(SW3)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table121
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).
SW3
214
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB1interfaceisdisabled.
SW256B3
04
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits768-815connected.Selectedif
SB1-0interfaceofSBMUX-Asinslots18&
22ofTC1C6(TCSA
1)connected.
SW256B4
05
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits1024-1071
connected.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table121
SW256BC109365
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
SW3
Switch
A.SelectedifSB1-0
interfaceofSBMUX-As
inslots18&22of
TC1C4(TCSA0)connected.
B.SelectedifSB1-0
interfaceofSBMUX-As
inslots18&22of
TC1C12(TCSA2)
connected.
SW256B5
06
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits1280-1327
connected.Selectedif
SB1-0interfaceofSBMUX-Asinslots18&
22ofTC1C0(TCSA
0)connected.
SW256B6
07
ON*)
ON*)
OFF
OFF
SB1interface,PCM
circuits1536-1583
connected.Selectedif
SB1-0interfaceofSBMUX-Asinslots18&
22ofTC1C2(TCSA
0)connected.
SW256B7
08
OFF
OFF
ON*)
OFF
SB1interface,PCM
circuits1792-1855
connected.
C.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot03connectedor
SB1interfaceofETS2/ETIP1-AinGTIC1
slot05connected.
D.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
&0slot07connected.
E.SelectedifSB3interfaceofETPE/Tin
slot6ofGTIC-0(for
BSC3i1000)connectedorselectedifSB3
interfaceofETPE/Tin
Issue:2-9
DN70630644
215
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table121
SerialBroadbandInterfaceSB1settingsontheSW256B(SW3).(Cont.)
SW3
Switch
slot1ofETC-5(for
BSC3i2000)connected.
F.SelectedifSB3interfaceofETPE/Tin
slot6ofGTIC0/GTIC
1connected.
*)IfSBMUX-AorETS2orETIP1-AorETPEorETPTisnotconnectedinthisPCMposition,
switchmustbeOFF.
A.CombinedBSC/TCSMinstallation,wheretheTCSMparthasonlyS15HWTCSM3icabinets.
B.CombinedBSC/TCSMinstallation,wheretheTCSMpartconsistsofbothS12-S14HW
TCSM3icabinetsandS15HWTCSM3icabinets.
C.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
D.STMU/ETIPHWredundancyinuse.
E.ETPE/TTXNredundancyinuse.
F.ETPE/THWredundancyinuse.
SerialBroadbandSB2settings(SW4)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table122
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).
SW4
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
01
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits64-127connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot01connected.
216
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table122
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
&1slot01connected.
C.SelectedifSB2interfaceofETPE/Tin
slot1ofETC-4(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot1ofETC-4/ETC-5
(forBSC3i2000)connected.
SW256B1
02
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits320-383connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot03connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
&1slot02connected.
C.SelectedifSB2interfaceofETPE/Tin
slot1ofGTIC-0(for
BSC1000)orselected
ifSB2interfaceof
ETPE/Tinslot6of
ETC-3(forBSC2000).
D.SelectedifSB2interfaceofETPE/Tin
slot1ofGTIC0/GTIC
1connected.
E.SelectedifSB2interfaceofETP(A)in
slot3ofETC-4(for
BSC3i2000)connected.
Issue:2-9
DN70630644
217
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table122
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
Switch
SW256B2
03
OFF
OFF
OFF
OFF
SB2interfaceisdisabled.
SW256B3
04
ON*)
ON*)
OFF
OFF
SB2interface,PCM
circuits832-879connected.Selectedif
SB1-0interfaceofSBMUX-Asinslots18&
22ofTC1C8(TCSA
1)connected.
SW256B4
05
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1088-1151
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot03connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot05connected.
B.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
C.SelectedifSB2interfaceofETPE/Tin
slot6ofETC-4(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot6ofETC4/ETC5
connected.
E.SelectedifSB2interfaceofETP(A)in
slot3ofGTIC-0(for
BSC3i1000)connectedorselectedifSB2
interfaceofETP(A)in
slot3ofETC-2(for
BSC3i2000)connected.
218
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table122
SW256BC109365
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
SW256B5
Switch
06
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1344-1407
connected.
A.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot01connected.
B.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
&0slot05connected.
C.SelectedifSB3interfaceofETPE/Tin
slot6ofETC-5(for
BSC3i2000)connected.
D.SelectedifSB3interfaceofETPE/Tin
slot1ofETC2/ETC3
connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1600-1663
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot01connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot02connected.
B.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
&0slot05connected.
C.SelectedifSB2interfaceofETPE/Tin
slot6ofETC-5(for
BSC3i2000)connected.
D.SelectedifSB2interfaceofETPE/Tin
slot1ofETC2/ETC3
connected.
Issue:2-9
DN70630644
219
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table122
SerialBroadbandInterfaceSB2settingsontheSW256B(SW4).(Cont.)
SW4
SW256B7
Switch
08
OFF
OFF
ON*)
OFF
SB2interface,PCM
circuits1856-1919
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot03connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot06connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot07connected.
C.SelectedifSB2interfacesofETPE/Tin
track6ofGTIC-0(for
BSC3i1000)orselectedifSB2interfacesof
ETPE/Tintrack1of
ETC-5(forBSC3i
2000).
D.SelectedifSB2interfaceofETPE/Tin
track6ofGTIC
0/GTIC1connected.
*)IfSBMUX-AorETS2orETIP1-AorETPEorETPTorETP(A)isnotconnectedinthis
PCMposition,switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
E.ETP(A)poolredundancyinuse.
SerialBroadbandSB3settings(SW5)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
220
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table123
SW256BC109365
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).
SW5
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
Note
SW256B0
01
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B1
02
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B2
03
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB3interfaceisdisabled.
SW256B4
05
ON*)
ON*)
OFF
OFF
SB3interface,PCM
circuits1152-1199
connected.
A.SelectedifSB1-0
interfaceofSBMUXAsinslots18&22of
TC1C10(TCSA1)
connected.
B.SelectedifSB1-0
interfaceofSBMUXAsinslots18&22of
TC1C14(TCSA2)
connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1408-1471
connected.
C.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC0
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot07connected.
D.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
Issue:2-9
DN70630644
221
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table123
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
SW256B6
Switch
07
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1664-1727
connected.
C.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot03connected.
D.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
E.SelectedifSB2interfacesofETPE/Tin
track6ofETC-2(for
BSC3i2000).
F.SelectedifSB2interfaceofETPE/Tin
track6ETC-2/ETC-3
connected(forBSC3i
2000).
SW256B7
08
OFF
OFF
ON*)
OFF
SB3interface,PCM
circuits1920-1983
connected.
C.SelectedifSB1interfaceofETS2/ETIP1-AinGTIC1
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot07connected.
D.SelectedifSB1interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
*)IfSBMUX-AorETS2orETIP1-AorETPEorETPTisnotconnectedinthisPCMposition,
switchmustbeOFF.
A.CombinedBSC/TCSMinstallation,wheretheTCSMparthasonlyS15HWTCSM3icabinets.
222
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table123
SW256BC109365
SerialBroadbandInterfaceSB3settingsontheSW256B(SW5).(Cont.)
SW5
Switch
B.CombinedBSC/TCSMinstallation,wheretheTCSMpartconsistsofbothS12-S14HW
TCSM3icabinetsandS15HWTCSM3icabinets.
C.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
D.STMU/ETIPHWredundancyinuse.
E.ETPE/TTXNredundancyinuse.
F.ETPE/THWredundancyinuse.
SerialBroadbandSB4settings(SW6)
ThesettingoftheSerialBroadbandInterfacecapacityispresentedinthetablebelow.
Table124
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).
Switch
SW256B0
Switch
Slot
1(1-8)
2(2-7)
3(3-6)
4(4-5)
01
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits192-255connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot01connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot02connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot01connected.
C.SelectedifSB3interfacesofETPE/Tin
track1ofETC-4(for
BSC3i2000).
Issue:2-9
DN70630644
223
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table124
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
D.SelectedifSB3interfaceofETPE/Tin
track1ofETC5/ETC4
connected(forBSC3i
2000).
SW256B1
02
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits448-511connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot04connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot02connected.
C.SelectedifSB3interfacesofETPE/Tin
track1ofGTIC-0(for
BSC3i1000)orselectedifSB3interfacesof
ETPE/Tintrack6of
ETC-3(forBSC3i
2000).
D.SelectedifSB3interfaceofETPE/Tin
track1GTIC0/GTIC1
connected.
E.SelectedifSB2interfaceofETP(A)in
track3ofETC-5(for
BSC3i2000)connected.
224
SW256B2
03
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
SW256B3
04
OFF
OFF
OFF
OFF
SB4interfaceisdisabled.
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table124
SW256BC109365
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
SW256B4
Switch
05
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1216-1279
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot03connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot06connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot03connected.
C.SelectedifSB3interfacesofETPE/Tin
track6ofETC-4(for
BSC3i2000).
D.SelectedifSB3interfaceofETPE/Tin
track6ofETC4/ETC5
connected(forBSC3i
2000).
E.SelectedifSB2interfaceofETP(A)in
track3ofGTIC-1(for
BSC3i1000)connectedorselectedifSB2
interfaceofETP(A)in
track3ofETC-3(for
BSC3i2000)connected.
SW256B5
06
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1472-1535
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC0
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC0slot08connected.
Issue:2-9
DN70630644
225
SW256BC109365
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table124
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC0
&1slot04connected.
SW256B6
07
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1728-1791
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot02connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot04connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot06connected.
C.SelectedifSB3interfacesofETPE/Tin
track6ofETC-2(for
BSC3i2000).
D.SelectedifSB3interfacesofETPE/Tin
track6ofETC2/ETC
3connected(for
BSC3i2000).
SW256B7
08
OFF
OFF
ON*)
OFF
SB4interface,PCM
circuits1984-2047
connected.
A.SelectedifSB2interfaceofETS2/ETIP1-AinGTIC1
slot04connectedor
selectedifSB1interfaceofETS2/ETIP1-A
inGTIC1slot08connected.
B.SelectedifSB2interfacesofETS2/ETIP1-AinGTIC1
&0slot08connected.
226
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Table124
SW256BC109365
SerialBroadbandInterfaceSB4settingsontheSW256B(SW6).(Cont.)
Switch
Switch
*)IfETS2orETIP1-AorETPEorETPTorETP(A)isnotconnectedinthisPCMposition,
switchmustbeOFF.
A.STMU/ETIPTXNredundancyisinuse.Thefirstinterfacesettingreferstofullcapacity
andthesecondinterfacesettingreferstohalfcapacity.
B.STMU/ETIPHWredundancyinuse.
C.ETPE/TTXNredundancyinuse.
D.ETPE/THWredundancyinuse.
E.ETP(A)poolredundancyinuse.
Issue:2-9
DN70630644
227
TR3EC109454,TR3AC109455,TR3TC111545
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
26 TR3EC109454,TR3AC109455,TR3TC111545
Jumperblocksoftheplug-inunit
Figure32
Jumpergroupoftheplug-inunitTR3E/A
P4
P2
Interchangeability
8 7 6 5
W7
1 2 3 4
P1
W7
DN05159743
Figure33
Jumpergroupoftheplug-inunitTR3T(version1)
Interchangeability
W12
P4
1
2
3
4
8
7
6
5
ETSI/ ANSImode
P2
1
W14
W12
1
W14
1
2
3
6
5
4
P1
DN70632821
228
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
Figure34
TR3EC109454,TR3AC109455,TR3TC111545
Jumpergroupoftheplug-inunitTR3T(version2)
Interchangeability
W12
P4
1
2
3
4
8
7
6
5
ETSI/ ANSImode
P2
1
W14
W12
1
W14
1
2
3
6
5
4
P1
DN0950625
Standardsettings
Jumpersforthesestandardsettingsaresetatthefactory,andnormallythereisnoneed
tochangethem.ForTR3E/AthejumperisW7,forTR3TitisW12.
ForTR3T,RJ45connectorhasbeenremoved.
Table125
InterchangeabilitycodesettingsofTR3E/A(W7)andTR3T(W12).
ICCcode
W7/W12settings
1-8
2-7
3-6
4-5
ON
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
Issue:2-9
DN70630644
229
TR3EC109454,TR3AC109455,TR3TC111545
Table125
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
InterchangeabilitycodesettingsofTR3E/A(W7)andTR3T(W12).(Cont.)
ICCcode
W7/W12settings
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ForTR3T,theETSIorANSIsettingwillhavetoselected.
Table126
ETSI/ANSIsettingsofTR3T(W14).
Jumper
Default
setting
Function
1-6
OFF
ON=ANSI
modeselected.OFF=ETSImodeselected.
2-5
3-4
230
Reservedfor
futureuse.
ON
ON=CPLD
downloading
withispdowloadis
enabled.OFF=CPLD
downloading
withispdowloadis
notenabled
DN70630644
Issue:2-9
JumperSettingsofthePlug-inUnitsinFlexiBSCand
TCSM3i
TR3EC109454,TR3AC109455,TR3TC111545
IncombinedBSC/TCSMinstallationETSImodemustalwaysbeselectedwhetherETSI
orANSImodeistobeused.
Issue:2-9
DN70630644
231