Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1. Scope*
1.1 This specification provides standard fitting geometries
and laying lengths for plastic fittings intended for use in drain,
waste, and vent applications. (See Specifications D2661 and
D2665.)
1.2 Fittings meeting the requirements of this standard specification are designed for use with outside diameter controlled
pipe. The inside diameter can vary significantly as the wall
thickness and outside diameter varies and therefore is not
suitable for use as a fitting socket.
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
and are not considered standard.
2. Referenced Documents
2.1 ASTM Standards:2
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.
Current edition approved Aug. 1, 2009. Published August 2009. Originally
approved in 1974. Last previous edition approved in 2009 as D3311 09. DOI:
10.1520/D3311-09A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standards Document Summary page on
the ASTM website.
4. Keywords
4.1 DWV; fittings; plastic; Schedule 40; thermoplastic
D3311 09a
TABLE 1 Bends, in. (mm)
Long Sweep
14 Bend
Bend
14
Bend
Bend
18
16
Bend
1 16
1916 (40)
134 (44)
2516 (59)
3116 (78)
378 (98)
5 (min) (127)
6 (152)
214 (57)
234 (70)
314 (83)
4116 (103)
41516 (125)
9 (229)
...
1 (25)
118 (29)
112 (38)
134 (44)
2316 (56)
2 (min) (51)
2116 (52)
(22)
1 (25)
1516 (33)
11116 (43)
2116 (52)
338 (86)
...
(11)
12 (13)
1116 (17)
1316 (21)
1 (25)
112 (38)
112 (38)
78
7 16
14
GG
3116 (78)
3116 (78)
378 (98)
4316 (106)
4716 (113)
5716 (138)
4116 (103)
4116 (103)
41516 (125)
434 (121)
41516 (125)
6 (152)
...
4116 (103)
...
...
558 (143)
...
...
214 (57)
...
D3311 09a
TABLE 3 Sanitary Tees, 45 Wyes, Combination Wyes and 18 Bends, in. (mm)
GN
GJ
GN
GJ
GN
GJ
(19)
1 (25)
138 (35)
11316 (46)
214 (57)
312 (89)
412 (114)
1916 (40)
134 (44)
2516 (59)
3116 (78)
378 (98)
5 (127)
6 (152)
1116 (27)
118 (29)
138 (35)
158 (41)
178 (48)
134 (44)
238 (60)
2916 (65)
278 (73)
358 (92)
5 (127)
638 (162)
8716 (214)
1134 (298)
(11)
12 (13)
1 (25)
118 (29)
11316 (46)
21516 (75)
338 (86)
412 (114)
6516 (160)
858 (219)
34
7 16
TABLE 4 Reducing Sanitary Tees, 45 Wyes, Combination Wyes, and 18 Bends, in. (mm)
G1
G2
G3
G4
G1
G2
G3
G1
G2
G3
(17)B
1 (25)
1316 (21)
1316 (30)
1316 (30)
138 (35)
1316 (30)
1316 (30)
1516 (24)
1316 (30)
1516 (24)B
1116 (27)B
118 (29)
134 (44)
2316 (56)B
258 (67)
3916 (90)
112 (38)B
134 (44)
11116 (43)
11516 (49)
11516 (49)
2516 (59)
11516 (49)
11516 (49)
134 (44)
218 (54)
2116 (52)B
2 (51)B
2116 (52)
3 (76)
358 (92)B
418 (105)
41316 (122)
11116 (43)B
134 (44)
11316 (46)
2316 (56)
2316 (56)
2516 (59)
2316 (56)
2316 (56)
2916 (65)
278 (73)
2716 (62)B
314 (83)B
3516 (84)
3916 (90)
4516 (110)B
514 (133)
512 (140)
11116 (43)B
134 (44)
11316 (46)
2316 (56)
2316 (56)
2516 (50)
2316 (56)
2316 (56)
2916 (65)
278 (73)
212 (64)B
314 (83)B
3516 (84)
3916 (90)
4516 (110)B
514 (133)
512 (140)
34 (19)B
1 (25)B
1116 (27)
12 (13)
78 (22)
0 (0)B
38 (10)
1116 (27)
316 (5)B
316 (5)B
38 (10)
1 (25)
21316 (71)B
312 (89)B
3516 (84)
334 (95)
418 (105)
3516 (84)B
11
4 16 (119)
5916 (141)
61516 (176)B
61116 (170)B
758 (194)
912 (241)
21516 (75)B
338 (86)B
3716 (87)
4516 (110)
458 (117)
31516 (100)B
9
5 16 (141)
6 (152)
7716 (189)B
7716 (189)B
858 (219)
91316 (249)
12 (13)
916 (14)
1 (25)
916 (14)
18 (3)
716 (11)
516 (8)
1116 (27)
1116 (17)B
916 (14)B
314 (83)
31116 (94)
1
4 2 (114)
31116 (170)
3716 (87)
434 (121)
3
4 4 (121)
638 (162)
71316 (198)B
71316 (198)B
3316 (81)
358 (92)
1
4 2 (114)
358 (92)
414 (108)
5516 (135)
7
5 8 (149)
678 (175)
81316 (224)B
81516 (227)B
11 16
D3311 09a
TABLE 5 60 Wyes, Single, and Double, in. (mm)
Nominal Pipe
Size
GN
GJ
Nominal Pipe
Size
G1
G2
G3
1 1 2
2
3
118 (40)
138 (37)
158 (37)
278 (73)
358 (92)
5 (127)
2 by 2 by 112
3 by 3 by 112
3 by 3 by 2
1116 (27)
12 (13)
78 (22)
3716 (87)
334 (95)
418 (105)
3716 (87)
4516 (110)
458 (117)
G1
G2
G3
1 12
2 by 112 by 112
2 by 2 by 112
1916 (40)
1716 (37)
1716 (37)
1316 (30)
1316 (30)
1516 (33)
114 (32)
114 (32)
114 (32)
Nominal
Pipe Size
OD
ID
1 1 2
2
3
1.900
2.375
3.500
1.500
1.939
2.900
Length
-in. increments from
close to 18 in. long
12
Nominal Pipe
Size
1 1 2
2
3
4
1316 (30)
112 (38)
178 (48)
212 (64)
58
34
78
58
(16)
(16)
(19)
(22)
Nominal Pipe
Size
Vent Tee
1 1 4
1 1 2
2
3
4
1 (25)
1316 (30)
112 (38)
178 (48)
212 (64)
Bend Vent
14
1 (25)
1316 (30)
112 (38)
178 (48)
212 (64)
D3311 09a
TABLE 11 Reducing Vent Tees, Single, and Double, in. (mm)
GN
2 by 1 by 1
2 by 2 by 112
3 by 3 by 112
3 by 3 by 2
1 (30)
1316 (30)
1316 (30)
112 (38)
12
12
GJ
1
112
178
178
3 16
12
(38)
(38)
(48)
(48)
Style 2
Style 3
Nominal Pipe
Size
CM
L1
CM
112 by 114
2 by 114
2 by 112
3 by 112
3 by 2
4 by 2
4 by 3
6 by 3
6 by 4
8 by 4
8 by 6
(24)
1116 (27)
1116 (27)
134 (44)
134 (44)
2 (51)
2 (51)
5
3 16 (84)
312 (89)
458 (117)
458 (117)
(5)
516 (8)
516 (8)
1 (25)
78 (22)
118 (29)
12 (13)
11316 (97)
134 (44)
278 (73)
158 (41)
(5)
316 (5)
316 (5)
14 (6)
14 (6)
14 (6)
14 (6)
516 (8)
12 (13)
58 (16)
58 (16)
...
...
...
134 (44)
134 (44)
2 (51)
2 (51)
...
...
...
...
...
...
...
34 (19)
78 (22)
78 (22)
112 (38)
...
...
...
...
...
...
...
14 (6)
14 (6)
14 (6)
14 (6)
...
...
...
...
1 (25)
118 (29)
1332 (28)
112 (38)
158 (41)
...
...
...
...
...
...
15 16
3 16
3 16
D3311 09a
TABLE 13 Couplings, Adapters, in. (mm)
Coupling
Female Adapter
Female Fitting
Adapter
Male Adapter
1.600
1.840
2.320
3.440
4.440
6.550
8.655
to
to
to
to
to
to
to
N, min
1.380
1.610
2.067
3.068
4.026
6.065
8.610
N, min
(3)
18 (3)
18 (3)
316 (5)
14 (6)
14 (6)
14 (6)
(6)
14 (6)
14 (6)
516 (8)
1132 (9)
...
...
18
14
N, min
A, max
(5)
316 (5)
316 (5)
38 (10)
38 (10)
...
...
1.290 (32.77)
1.552 (39.42)
2.067 (52.50)
3.068 (77.93)
4.026 (102.26)
...
...
3 16
Nominal
Pipe Size
N, min
114 by 112
112 by 2
112 by 3
2 by 3
2 by 4
3 by 4
(10)
(13)
1332 (28)
78 (22)
138 (35)
1516 (24)
13 32
17 32
N, min
(4)
(4)
532 (4)
732 (6)
14 (6)
...
...
5 32
5 32
D3311 09a
TABLE 15 Trap Adapters, in. (mm)
Without stop
With Stop
Nominal
Pipe Size
N, min
1 1 4
1 1 2
2
114 by 112
316
316
3 16
3 16
A, min
(5)
(5)
(5)
(5)
1.250
1.500
2.000
1.250
(32)
(38)
(51)
(32)
Nominal
Pipe Size
1 1 4
1 1 2
2
2 1 2
3
3 1 2
4
6
8
(13)
(16)
58 (16)
34 (19)
34 (19)
34 (19)
78 (22)
1 (25)
138 (35)
1 (25)
138 (35)
138 (35)
112 (38)
134 (44)
134 (44)
178 (48)
2 (51)
238 (60)
1 (25)
1 (25)
114 (32)
114 (32)
158 (41)
158 (41)
2 (51)
214 (32)
312 (89)
12
58
D3311 09a
TABLE 17 Hubs, in. (mm)
Nominal
Pipe Size
AJ
2
3
4
Reducing 4 by 3
...
3.448 (87.58)
4.493 (114.12)
4.493 (114.12)
...
11116 (43)
11516 (49)
11516 (49)
...
(8)
1132 (9)
516 (8)
2.94 (74.7)
3.94 (100.1)
4.94 (125.5)
4.94 (125.5)
5 16
CJ
2 3 8
258
278
278
(60)
(67)
(73)
(73)
N
(10)
(11)
12 (13)
716 (11)
38
7 16
Nominal
Pipe Size
L2, min
2
3
4
312 (89)
334 (95)
4 (102)
L1, min
458 (117)
558 (143)
618 (156)
L3, min
(10)
(10)
38 (10)
38
38
AN
max
min
2.75 (69.9)
3.88 (98.6)
4.88 (124.0)
2.63 (66.8)
3.63 (92.2)
4.63 (117.6)
2.00 (50.8)
3.00 (76.2)
4.00 (101.6)
D3311 09a
TABLE 19 Reducing Spigots, in. (mm)
Nominal
Pipe Size
L2 min
2 by 112
3 by 112
3 by 2
4 by 2
4 by 3
312 (89)
334 (95)
334 (95)
4 (102)
4 (102)
L1 min
L3 min
414 (108)
412 (114)
458 (117)
478 (124)
512 (140)
3 8
3 8
3 8
38
38
(10)
(10)
(10)
(10)
(10)
AJ
max
min
2.75 (69.9)
3.88 (98.6)
3.88 (98.6)
4.88 (124.0)
4.88 (124.0)
2.63 (66.8)
3.63 (92.2)
3.63 (92.2)
4.63 (117.6)
4.63 (117.6)
2.00 (50.8)
3.00 (76.2)
3.00 (76.2)
4.00 (101.6)
4.00 (101.6)
Nominal
Pipe Size
min GJ
min GGJ
min GGN
min GN
min R
1 1 4
1 1 2
2
3
4
418 (105)
4732 (107)
714 (184)
8716 (214)
101316 (275)
338 (86)
358 (92)
4116 (103)
6516 (160)
778 (200)
3 (76)
3 (76)
5 (127)
1
6 4 (159)
8116 (205)
138 (35)
138 (35)
214 (57)
258 (67)
3716 (87)
158 (41)
158 (41)
212 (64)
318 (79)
4116 (103)
D3311 09a
TABLE 21 Double Fixture Fitting, in. (mm)
G1
G2
G3
G4
12
(10)
(10)
(13)
3 (90)
4916 (116)
634 (171)
2 (62)
3116 (78)
412 (114)
2 (62)
3116 (78)
412 (114)
(10)
(10)
38 (10)
3916 (90)
4916 (116)
4916 (116)
2716 (62)
3116 (78)
3116 (78)
2716 (62)
3116 (78)
3116 (78)
9 16
38
38
38
38
7 16
7 16
G2
G3
G4
(10)
38 (10)
12 (13)
318 (79)
414 (108)
614 (159)
21116 (68)
312 (89)
41516 (125)
(10)
318 (79)
(10)
(10)
12 (13)
414 (108)
414 (108)
614 (159)
38
R1
R2
21116 (68)
312 (89)
41516 (125)
358 (92)
412 (114)
658 (168)
358 (92)
412 (114)
658 (168)
278 (73)
278 (73)
358 (92)
358 (92)
278 (73)
312 (89)
41516 (125)
312 (69)
312 (89)
41516 (125)
358 (92)
412 (114)
658 (168)
412 (114)
412 (114)
658 (168)
Reducing
2 by
1 1 2
2 by
2 by
3 by
112 by 112 by
38
112 by 112 by 2
112 by 2 by 2
2 by 3 by 3
38
38
10
D3311 09a
TABLE 23 Single and Double Long Turn Tee, in. (mm)
G1
G2
(10)
(11)
1116 (17)
1116 (27)
112 (38)
212 (64)
3716 (87)
31516 (100)
518 (130)
7916 (192)
10 (254)
1538 (391)
3116 (78)
312 (89)
4716 (113)
612 (165)
812 (216)
1278 (327)
434 (121)
578 (149)
7 (178)
1018 (257)
1314 (337)
19 (483)
38
7 16
TABLE 24 Single and Double Long Turn Tee Reducing, in. (mm)
G1
G3
G2
(10)
(10)
716 (11)
1116 (17)
38 (10)
716 (11)
716 (11)
1116 (17)
38 (10)
58 (16)
1116 (27)
916 (14)
1516 (24)
112 (38)
2 (51)
358 (92)
358 (92)
4316 (107)
518 (130)
31316 (97)
4316 (102)
434 (121)
51116 (128)
5316 (132)
618 (156)
8116 (205)
718 (181)
9116 (230)
11 (279)
13516 (338)
3116 (78)
3116 (78)
312 (89)
4716 (113)
3116 (78)
312 (89)
312 (89)
4716 (113)
3916 (90)
412 (114)
612 (165)
4916 (116)
658 (168)
812 (216)
1034 (273)
3716 (87)
3716 (87)
31516 (100)
518 (130)
3716 (87)
31516 (100)
31516 (100)
518 (130)
31516 (100)
518 (130)
7916 (192)
518 (130)
7916 (192)
10 (254)
1234 (324)
434 (121)
434 (121)
578 (200)
7 (178)
434 (121)
578 (149)
578 (149)
7 (178)
578 (149)
7 (178)
1018 (257)
7 (178)
1018 (257)
1314 (337)
16 (406)
38
38
11
D3311 09a
TABLE 25 Three-Way EII, in. (mm)
Nominal
Pipe Size
1 1 2
2
3
4
Reducing
2 by 112 by 112 (short)
3 by 2 by 3
2 by 112 by 112 (long)
G1
G2
G3
134 (44)
2516 (59)
3116 (78)
378 (98)
134 (44)
2516 (59)
3116 (78)
378 (98)
134 (44)
2516 (59)
3116 (78)
378 (98)
158 (41)
3116 (78)
11516 (49)
158 (41)
278 (73)
2316 (56)
158 (41)
3116 (78)
2316 (56)
3
4
4116 (103)
41516 (125)
12
D3311 09a
TABLE 27 Sanitary Tees, with Side Inlet, in. (mm)
G1
G2
G3
G4
G5
234 (70)
31116 (94)
3516 (84)
3516 (84)
478 (124)
478 (124)
618 (156)
134 (44)
2516 (59)
218 (54)
218 (54)
3116 (78)
3116 (78)
378 (98)
134 (44)
2516 (59)
278 (73)
278 (73)
3116 (78)
3116 (78)
378 (98)
134 (44)
2516 (59)
2916 (65)
278 (73)
2916 (65)
278 (73)
3516 (84)
134 (44)
2516 (59)
218 (54)
218 (54)
31116 (94)
31116 (94)
5 (127)
3516 (84)
3516 (84)
478 (124)
478 (124)
618 (156)
218 (54)
218 (54)
3116 (78)
3116 (78)
378 (98)
278 (73)
278 (73)
3116 (78)
3116 (78)
378 (98)
2916 (65)
278 (73)
2916 (65)
278 (73)
3516 (84)
218 (54)
218 (54)
31116 (94)
31116 (94)
5 (127)
3516 (84)
3516 (84)
478 (124)
478 (124)
618 (156)
218 (54)
218 (54)
3116 (78)
3116 (78)
378 (98)
278 (73)
278 (73)
3116 (78)
3116 (78)
378 (98)
2916 (65)
278 (73)
2916 (65)
278 (73)
3516 (84)
218 (54)
218 (54)
31116 (94)
31116 (94)
5 (127)
G1
G2
G3
G4
G5
3 by 112
3 by 2
4 by 2
478 (124)
478 (124)
618 (156)
3116 (78)
3116 (78)
378 (98)
3116 (78)
3116 (78)
378 (98)
2916 (65)
278 (73)
3516 (84)
31116 (94)
31116 (94)
378 (min) (98)
3 by 112 by 112
3 by 2 by 2
4 by 2 by 2
478 (124)
478 (124)
618 (156)
3116 (78)
3116 (78)
378 (98)
3116 (78)
3116 (78)
378 (98)
2916 (65)
278 (73)
3516 (84)
31116 (94)
31116 (94)
5 (127)
13
D3311 09a
TABLE 29 Sanitary Tees, with Slip Joint, in. (mm)
1 1 4
1 1 2
112 by 114 by 112
Sanitary Tee
G1
G2
214 (57)
234 (70)
212 (64)
112 (38)
134 (44)
134 (44)
G1
G2
G3, min
214 (57)
234 (70)
212 (64)
112 (38)
134 (44)
134 (44)
3 (76)
3 (76)
3 (76)
Nominal
Pipe Size
2 by 2 by 2
3 by 3 by 3
Reducing
2 by 2 by 112
3 by 3 by 2
G1 min
G2 min
G3 min
512 (140)
712 (191)
5316 (132)
738 (187)
334 (95)
514 (133)
414 (108)
5316 (132)
418 (105)
5516 (135)
3116 (78)
4916 (116)
by
by
by
by
3
3
3
3
by
by
by
by
G1
414 (108)
414 (108)
5 (127)
5 (127)
G2
1 2
7 8
7 8
12
14
(13)
(13)
(22)
(22)
G3
G4
G5
4516 (110)
4516 (110)
458 (117)
458 (117)
3316 (81)
3316 (81)
314 (83)
314 (83)
134 (44)
134 (44)
2516 (59)
2516 (59)
D3311 09a
TABLE 32 Vertical Closet Bend, with Auxiliary Inlets, in. (mm)
G1
G2
G3
G4
G5
G6
G7
712 (191)
712 (191)
712 (191)
538 (137)
538 (137)
538 (137)
618 (156)
618 (156)
618 (156)
3532 (80)
5532 (80)
3532 (80)
234 (70)
234 (70)
234 (70)
278 (73)
278 (73)
278 (73)
278 (73)
278 (73)
278 (73)
Nominal
Pipe Size
G1
3 by 4 by 2V by 2 RH.AI
3 by 4 by 2V by 2 LH.AI
G2
G3
G4
G5
(14)
4 (114)
(59)
15 32
(14)
412 (114)
2516 (59)
15 32
4 (117)
9 16
458 (117)
9 16
58
12
5 16
G6
G7
G8
(12)
(157)
2 (73)
9 32
(12)
6316 (157)
278 (73)
9 32
3 16
78
(7)
(7)
14
Nominal Pipe
Size
1 1 2
Fem. NPSM
3 Spigot
Fem. NPSM
3Hub
L, min
338 (86)
178 (48)
15
G9
14
(6)
(6)
D3311 09a
TABLE 35 Swivel Strainer, Adapter, in. (mm)
Short
Nominal
Pipe Size
L1
1 12
11116 (43)
Long
L2
L1
(16)
2716 (62)
58
L2
(16)
58
N, min
1 1 4
1 1 2
2
3
4
(4)
532 (4)
532 732 (4)
(6)
14 (6)
I, min
5 8
5 8
3 4
7 8
12
5 32
16
(13)
(16)
(16)
(19)
(22)
W, min
11132 (34)
11532 (37)
11732 (39)
21532 (63)
234 (70)
D3311 09a
TABLE 37 Cut-In Adapter
...
...
...
...
...
...
...
...
...
...
...
114 (32)
212 (64)
0.60 (15.2)
1 (25)
0.53 (13.5)
114 (32)
2.385 (60.58)
2.940 (74.69)
2.380 (60.45)
2.577 (65.46)
2.385 (60.58)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
12
L
L1
L2
L3
L4
L5
D1
D2
D3
D4
D5
M
(min)
E
(min)
L
(min)
THD
(min)
1732
(512)
14
(6)
34
(18)
398
17
D3311 09a
TABLE 39 4 by 3 in. Threaded Closet Flange (FPT)
M
(min)
E
(min)
L
(min)
THD
(min)
732
(512)
14
(6)
34
(18)
398
18
D3311 09a
TABLE 40 4 by 3 in. Closet Flange (Spigot)
M
(min)
E
(min)
L
(min)
732
(512)
14
(6)
34
(18)
19
D3311 09a
TABLE 41 4 by 3 in. Closet Flange (HUB)
M
(min)
E
(min)
L
(min)
732
(512)
14
(6)
114
(32)
20
D3311 09a
TABLE 42 4 by 4 in. Closet Flange (HUB)
M
(min)
E
(min)
L
(min)
732
(512)
14
(6)
2
(51)
21
D3311 09a
TABLE 43 Drain Base Hub/Spigot for Roof, Floor and Sediment Drains
NOTE 112 in. FPT Primer Tap, Optional in All Configurations with Optional Knockout
NOTE 2Inserts Used in Securing Clamping Collars or Underdeck Clamp, Optional in all Configurations Nominal Pipe/Spigot or Gasket Sizes: 1 12
in., 2 in., 3 in., 4 in., 6 in.
5.25 6 0.10
(13.3 6 0.25)
5.00 6 0.10
(12.7 6 0.25)
5.25 6 0.10
(13.3 6 0.25)
6.00 6 0.10
(15.2 6 0.25)
12
(30.5)
12
(30.5)
12
(30.5)
12
(30.5)
3
4
6
22
D3311 09a
TABLE 44 4 by 3in. Offset Closet Flange (Hub)
NOTE
NOTE
NOTE
NOTE
NOTE
L,
Typical Height
C,
Offset
D,
Diameter
4.5 6 -18
(11.4 6 0.32)
2 6 -14
(5.1 6 0.64)
7 6 -14
(17.8 6 0.64)
23
E,
Flange Thickness
min.
(0.64)
14
D3311 09a
TABLE 45 Selectable Angle Bends, in. (mm)
1 1 2
ANGLE, degrees
11 ( bend)
15
20
2212 (116 bend)
25
30
35
40
45 (18 bend)
50
55
60 (16 bend)
65
70
75
80
85
88.8 (pitch 1 12 min)
90 (14 bend)
0.96 (24)
1.05 (27)
1.16 (30)
1.22 (31)
1.28 (33)
1.40 (36)
1.53 (39)
1.66 (42)
1.79 (45)
1.92 (49)
2.07 (52)
2.22 (56)
2.37 (60)
2.54 (64)
2.71 (69)
2.90 (74)
3.11 (79)
3.27 (83)
3.33 (84)
0.42 (11)
0.51 (13)
0.63 (16)
0.69 (18)
0.75 (19)
0.87 (22)
0.99 (25)
1.12 (28)
1.25 (32)
1.39 (35)
1.53 (39)
1.68 (43)
1.84 (47)
2.00 (51)
2.18 (55)
2.37 (60)
2.57 (65)
2.74 (70)
2.79 (71)
1.01 (26)
1.11 (28)
1.24 (31)
1.31 (33)
1.38 (35)
1.52 (39)
1.66 (42)
1.80 (46)
1.95 (50)
2.11 (54)
2.27 (58)
2.44 (62)
2.62 (67)
2.81 (71)
3.01 (77)
3.23 (82)
3.46 (88)
3.65 (93)
3.71 (94)
0.46 (12)
0.56 (14)
0.69 (18)
0.76 (19)
0.83 (21)
0.97 (25)
1.11 (28)
1.26 (32)
1.41 (36)
1.56 (40)
1.73 (44)
1.90 (48)
2.08 (53)
2.27 (58)
2.47 (63)
2.68 (68)
2.91 (74)
3.10 (79)
3.17 (81)
14
1 32
24
DIMENSIONS
A
1.71 (43)
1.92 (49)
2.02 (51)
2.13 (54)
2.34 (59)
2.56 (65)
2.79 (71)
3.02 (77)
3.26 (83)
3.51 (89)
3.78 (96)
4.05 (103)
4.34 (110)
4.65 (118)
4.99 (127)
5.34 (136)
5.63 (143)
5.74 (146)
4
B
0.84 (21)
1.04 (26)
1.15 (29)
1.25 (32)
1.47 (37)
1.69 (43)
1.91 (49)
2.14 (54)
2.39 (61)
2.64 (67)
2.90 (74)
3.18 (81)
3.47 (88)
3.78 (96)
4.11 (104)
4.47 (113)
4.76 (121)
4.86 (123)
2.16 (55)
2.27 (58)
2.39 (61)
2.64 (67)
2.89 (73)
3.14 (80)
3.40 (86)
3.68 (93)
3.96 (101)
4.26 (108)
4.57 (116)
4.91 (125)
5.26 (134)
5.64 (143)
6.04 (153)
6.37 (162)
6.48 (165)
1.19 (30)
1.31 (33)
1.43 (36)
1.67 (42)
1.92 (49)
2.17 (55)
2.44 (62)
2.71 (69)
2.99 (76)
3.29 (84)
3.61 (92)
3.94 (100)
4.29 (109)
4.67 (119)
5.07 (129)
5.40 (137)
5.51 (140)
D3311 09a
TABLE 46 45 Slip Joint Double Y
Nominal
Pipe Size
2 by 112 by 112 by 112
G1
G2
G3
G4
G5
G6
5 1 2
4 1 4
1 1 2
3 7 8
1 1 4
1316
1 1 2
25
D3311 09a
26
D3311 09a
SUMMARY OF CHANGES
Committee F17 has identified the location of selected changes to this standard since the last issue (D331109)
that may impact the use of this standard.
(1) Table 13 was revised.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org).
27