Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
export@generalmembrane.it
GENERAL MEMBRANE S.p.A. -ViaVenezia,538 - 30022 - Ceggia (VE) ITALY -Tel.+ 39 0421.322.000 - Fax.+39 0421.322.800 - export@generalmembrane.it - www.generalmembrane.it
EagleXtra SA membranes are made from high quality, self-adhered elasto-plastomeric compounds. The outer surface consists
of aplastomeric compound while the inner surface and the selvedge side consist of a SBS pressure-sensitive adhesive compound.
EagleXtra SA membranes are manufactured with non-woven polyester fiber fabric, stabilized with glass and rot-proof, to give
the membranes excellent dimensional stability. This ensures high performance with no waterproof surface shrinkage, even in
the case of roofing subjected to high thermal stresses. EagleXtra SA meets stringent standards for tensile strength, elongation
at break and tear strength.
EagleXtra SA Granular is finished with granules on the top surface and PE film + removable silicon selvedge.
APPLICATIONS
PRODUCT ADVANTAGES
C C
forma
a caldo
invecchiamento
ai raggi
UV UV
forma
aafreddo
caldo
a freddo
invecchiamento
forma
forma
a caldo
a caldo
aiinvecchiamento
raggi
invecchiamento
ai raggi
ai raggi
UVdimensionale
UVdimensionale
termico
termico
termico
termico
a trazione
a rottura
lacel
adimensionale
trazione
dimensionale
a rottura
a trazione
a trazione
SURFACE FINISHING
esistenza
aFlessibilit
ResistenzaStabilit
Stabilit
Resistenza
Allungamento
Resistenza
a Resistenza
Resistenza
aAllungamento
Resistenza
Resistenza
Pedonabilit
Stabilit
di
Resistenza
a Allungamento
Resistenza
Stabilit
Resistenza
a al alResistenza
a
Pedonabilit
a
Resistenza
Resistenza
a
Resistenza
a
alFacilitResistenza
stenza
aPedonabilit
Resistenza
Stabilit
Resistenza
Allungamento
Resistenza
a Facilit
Resistenza
aResistenza
Facilit
Resistenza
Resistenza
Pedonabilit
ai raggi
UVforma a caldo invecchiamento
dimensionale
aUV
trazione
a rottura
lacerazione
punzonamento
dettagli
vapore
dacqua
radici n
ai raggi
dimensionale
apunzonamento
trazione
rottura
punzonamento
Vecchiamentoa freddo
a trazione
a rottura
lacerazione
punzonamento
nei dettagli
vaporeadacqua
allelacerazione
radici
chiamento
ai raggi
UVdimensionale
dimensionale
a trazione
a rottura
lacerazione
neinei
dettagli
vapore
dacqua
allealle
radici
SAND
termico SURFACE
statico
POLYOLEFIN
termico
statico
statico
rmico
statico
GRANULAR
FINISHING
PRODUCT DATA
SURFACE
BACKING
GRANULAR
COLORS
AVAIBLE
RED
GREEN
TECHNICAL DESCRIPTION
BROWN
DARK GRAY
LIGHT GRAY
WHITE
Coverage (Nominal)
100 sq ft
Weight (Approx)
90 lbs
Roll Size
3210 x 39 3/8 (10m x 1m)
Rolls/Pallet
20
COMPANY PROFILE
TECHNICAL CHARACTERISTICS
CHARACTERISTIC
TEST METHOD
PROPERTY
TYPICAL VALUES
ASTM D5147
mm (mils)
3.5 (140)
Peak load
ASTM D5147
@232C [73.43.6F],
MD and XMD, kN/m (lbf/in.)
8.8 (50)
Elongation
ASTM D5147
@232C [73.43.6F]
MD and XMD, %
23
Tear Strength
ASTM D5147
@232C [73.43.6F]
MD and XMD, N (lbf)
311 (70)
ASTM D6222
C (F)
0 (32F)
Granule Embedment
ASTM D5147
APPLICATIONS INSTRUCTIONS
EagleXtra SA can be applied when the environmental temperature is at least 40F and with a reasonable air humidity. The
eventual humidity entrapped between membrane and substrate could lead to a formation of bubbles.
Substrates must be dry, free of pollutants and loose matter. Concrete decks should be properly primed prior to the application of
the membrane. Begin at the lowest point of the roof. Unroll the material and allow it to relax. Begin by removing the first 18-24
of release film. Press the membrane into place with firm and even pressure. Roll the edges with a silicone hand roller to ensure
complete adhesion. Step-by-step remove the remaining release film applying pressure from the center to the edges as you go.
Place consecutive rolls with a minimum of 6 end lap and 4 side lap; to improve the end lap joint, remove the granulates on the
6 long overlap. Laps can be sealed for additional water tightness with a hot air welder. When the installation of the entire roof
surface is finished, roll with an 80# split-face linoleum roller. Be careful on sloped roofs by securing the roller and applicator
with the right safety equipment. Check project details for proper installation requirements.
CONTATCTS: For further information regarding specifications, applications, or product information contact your local representative.
GENERAL MEMBRANE S.p.A. - Via Venezia, 538 - 30022 - Ceggia (VE) ITALY - Tel. + 39 0421.322.000 - Fax. +39 0421.322.800 - info@generalmembrane.it - www.generalmembrane.it