0 valutazioniIl 0% ha trovato utile questo documento (0 voti)
26 visualizzazioni3 pagine
The meeting minutes summarized a presentation from POSCO South Asia to VW India regarding the development of door side impact beams and seat rails using POSCO's materials. Key discussion points included POSCO providing sample sheets of two proposed grades of steel in different thicknesses for door impact beams for testing. POSCO also requested samples of the current supplier's materials for comparison. For seat rails, POSCO agreed to provide samples of their CR980DP steel for testing as a potential replacement for the material currently sourced from another supplier. Next steps included POSCO analyzing samples and providing further data for additional discussions between the companies.
The meeting minutes summarized a presentation from POSCO South Asia to VW India regarding the development of door side impact beams and seat rails using POSCO's materials. Key discussion points included POSCO providing sample sheets of two proposed grades of steel in different thicknesses for door impact beams for testing. POSCO also requested samples of the current supplier's materials for comparison. For seat rails, POSCO agreed to provide samples of their CR980DP steel for testing as a potential replacement for the material currently sourced from another supplier. Next steps included POSCO analyzing samples and providing further data for additional discussions between the companies.
The meeting minutes summarized a presentation from POSCO South Asia to VW India regarding the development of door side impact beams and seat rails using POSCO's materials. Key discussion points included POSCO providing sample sheets of two proposed grades of steel in different thicknesses for door impact beams for testing. POSCO also requested samples of the current supplier's materials for comparison. For seat rails, POSCO agreed to provide samples of their CR980DP steel for testing as a potential replacement for the material currently sourced from another supplier. Next steps included POSCO analyzing samples and providing further data for additional discussions between the companies.
MINUTES OF MEETING SUBJECT: Presentation on CR 980DP & seat rail development material
MEETING HELD AT: VW-Plant-MIDC,Chakan Phase-I, Pune
ON: 14th Jan, 2014 ATTENDED BY: VW -
India Pvt Ltd:
Mr.Maheshwar Joshi Mr.Rohit Rai Mr.Samadhan Patil Mr. Dhaval Deuskar
POSCO South Asia :
- Mr.KI-Young Chun(MD) -
Mr. Pankaj Shangrapawar, Manager
Summery of Issues : A. Door Side Impact Beam
1. In month of Nov, VW has requested POSCO, to change the
supplier from AM to POSCO for door side impact beam, VW wants to develop this in GI 980 DP with VW spec HX660HD 2. The total requirement for this material is 2500mt/Yr 3. In dec 13 POSCO has shared the guaranteed spec(mechanical & chemical properties) to VW
VW India Pvt Ltd
4. In this meeting POSCO proposed two grades LOW YS STEEL with
minimum YS is 580~750 Mpa & HIGH YS STEEL with minimum YS 700~900 5. VW was not sure about which material they should go for LOW YS or HIGH YS 6. So, they requested sample for both LOW & HIGH YS product 5 nos Each in 1.35mm & 1.0mm thickness 7. Currently they VW consuming 1.35mmt & 1.0mmt for HX660XD 8. The SQS sheet is mandatory with this sample 9. Once POSCO submit these sample VW sent in there lab and then stamping will be done 10. These stamping will be takes place at their vendor COSMA & SKH plant 11. POSCO also requested sample of Arcelor mittal to analyze their exact requirement , as the sheet which POSCO has submitted to VW showing TS of 956 Mpa which is lower than acceptable TS of 980Mpa B. Seat Rail
1. Currently VW is using HRPO 1.8mmt the grade is S500MC
equivalent to SAPH440 for upper rail, this material they are sourcing from domestic mill 2. For Lower rail VW required CR DP 980 with 1.2mmt , currently buys from Arcelor mittal 3. The total qty requirement is 150mt/Month 4. VW wants these CR to be sourced from POSCO 5. POSCO requested for CR 980DP sample 6. The vendor for seat rail is SKH Next action: 1. POSCO needs to collect the sample of Arcelor mittal grade HX660XD and send it to P-HQ for further analysis 2. P-SA needs to request 5 sample each for 1.35mmt of LOW YS & HIGH YS steel 3. Also for seat rail POSCO need to collect the samples 4. Once we shared the analysis, then POSCO & VW will discuss further