Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
{Adjust/Replace}{Production}{KodakServiceSupport}{None}
B144_0002BC
PLEASE NOTE
The information contained herein is based on the experience and knowledge relating to the
subject matter gained by Eastman Kodak Company prior to publication.
No patent license is granted by this information.
Eastman Kodak Company reserves the right to change this information without notice, and
makes no warranty, express or implied, with respect to this information. Kodak shall not be
liable for any loss or damage, including consequential or special damages, resulting from any
use of this information, even if loss or damage is caused by Kodaks negligence or other fault.
This equipment includes parts and assemblies sensitive to damage from electrostatic
discharge. Use caution to prevent damage during all service procedures.
Table of Contents
Description
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEPARATOR MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPPER SCAN MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPPER TRANSPORT AY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEED MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOWER SCAN MODULE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOWER TRANSPORT AY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRANSPORT MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXIT ROLLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRE-APERTURE and POST-APERTURE ROLLERS . . . . . . . . . . . . . . . . . . . . . .
TAKE-AWAY ROLLER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT BOARD COVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100 and 200 BOARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
3
4
4
6
8
10
13
15
20
22
24
26
29
32
34
Section 1: Adjustments
Important
Adjustments
Replacements
Section 2: Replacements
SEPARATOR MODULE
Prerequisites:
None
To Remove:
Warning
Dangerous Voltage
1 De-energize the equipment.
2 Disconnect the main power.
3 Remove the EXIT TRAY.
LATCH
UPPER TRANSPORT AY
B144_0055ACA
B144_0055AC
SEPARATOR MODULE
B144_0027BCA
B144_0027BC
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
Replacements
COVER
Prerequisites:
1 Remove the SEPARATOR MODULE.
To Remove:
SCREWS
B144_0028BCA
B144_0028BC
COVER
Replacements
B144_0037ACA
B144_0037AC
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
To Remove:
EMI COVER
3 SCREWS
SCREW
Warning
Dangerous Voltage
P/J302
1 Remove:
3 SCREWS
EMI COVER
2 Disconnect the VIDEO CABLE.
UPPER
SCAN MODULE
VIDEO
CABLE
B144_0024GCA
B144_0024GC
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
Replacements
UPPER TRANSPORT AY
Prerequisites:
1 Remove:
SEPARATOR MODULE
COVER
UPPER SCAN MODULE
To Remove:
PARTITION
Warning
Dangerous Voltage
CN1
1 Disconnect:
INVERTER
CN1
CN2
2 Remove and keep:
INVERTER BOARD
UDS RECEIVER
PARTITION
UDS RECEIVER
CN2
B144_0063GCA
B144_0063GC
Replacements
12SEP02
AR3177-1
Page
11 of 37
IMAGING GUIDE
B144_0062ACA
B144_0062AC
2 PLATES
2 SPRINGS
4 SCREWS
2 PLATES
STRUCTURE
5 Remove the UPPER TRANSPORT AY.
STRUCTURE
2 SPRINGS
UPPER TRANSPORT AY
B144_0064GCA
B144_0064GC
To Install:
1 Install the following parts on the new UPPER TRANSPORT AY.
STRUCTURE
2 PLATES
4 SCREWS
2 SPRINGS
UDS RECEIVER
INVERTER BOARD
PARTITION
2 Connect:
CN1
CN2
3 Clean both sides of the IMAGING GUIDE.
4 Install the IMAGING GUIDE.
Postrequisites:
None
Replacements
Replacements
FEED MODULE
Prerequisites:
None
To Remove:
Warning
Dangerous Voltage
1 De-energize the equipment.
2 Disconnect the main power.
3 Remove the EXIT TRAY.
LATCH
UPPER TRANSPORT AY
B144_0036ACB
B144_0036AC
INPUT TRAY
Replacements
PRE-APERTURE COVER
FEED MODULE
MOUNT
B144_0023BCA
B144_0023BC
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
To Remove:
LATCH
UPPER TRANSPORT AY
Warning
Dangerous Voltage
1 De-energize the equipment.
2 Disconnect the main power.
3 Remove the EXIT TRAY.
4 Release the LATCH.
5 Lift the UPPER TRANSPORT AY to the
service position.
6 Remove the INPUT TRAY.
B144_0036ACB
B144_0036AC
INPUT TRAY
RIBBON CABLE
Warning
PANEL
B144_0039ACA
B144_0039AC
Replacements
12SEP02
AR3177-1
Page
16 of 37
RETAINER
B144_0026HCA
B144_0026HC
RETRACTOR
No
No action
Replacements
12SEP02
AR3177-1
Page
17 of 37
VIDEO CABLE
LAMP DRIVER HARNESS
15 Observe the routing of the HARNESS.
INVERTER
Warning
CN2
EMI COVER
Dangerous Voltage
16 Disconnect CN2.
17 Remove the INVERTER BOARD and
LAMP DRIVER HARNESS.
B144_0057ACA
B144_0057AC
Replacements
LAMP
2 PUSH NUTS
2 SPRINGS
RETRACTOR
B144_0043BCA
B144_0043BC
LOWER
SCAN MODULE
18 Remove:
LAMP
2 PUSH NUTS
2 SPRINGS
2 RETRACTORS
Important
PIN
Replacements
To Install:
RIBBON CABLE
Caution
B144_0022ACA
B144_0022AC
Postrequisites:
None
Replacements
LOWER TRANSPORT AY
Prerequisites:
1 Remove:
LOWER SCAN MODULE
CIRCUIT BOARD COVER
To Remove:
POST-APERTURE COVER
LOWER TRANSPORT AY
SCREWS
2 SCREWS
P/J2
P/J209
P/J MOTOR
B144_0029HCA
B144_0029HC
Caution
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
Replacements
TRANSPORT MOTOR
Prerequisites:
1 Remove:
LOWER SCAN MODULE
LOWER TRANSPORT AY
To Remove:
2 SCREWS
BELT
1 Remove:
2 SCREWS
TRANSPORT MOTOR
BELT
TRANSPORT
MOTOR
B144_0020ACA
B144_0020AC
To Install:
1 Install:
TRANSPORT MOTOR
2 SCREWS
BELT
Replacements
12SEP02
AR3177-1
Page
23 of 37
2 SCREWS
TRANSPORT MOTOR
Postrequisites:
None
B144_0034ACA
B144_0034AC
Replacements
EXIT ROLLER
Prerequisites:
None
To Remove:
Warning
Dangerous Voltage
1 De-energize the equipment.
2 Disconnect the main power.
3 Remove the EXIT TRAY.
LATCH
UPPER TRANSPORT AY
B144_0055ACA
B144_0055AC
Replacements
POST-APERTURE COVER
EXIT ROLLER
2 WASHERS
2 BEARINGS
2 WASHERS
2 E-RINGS
2 BEARINGS
BELT
B144_0021GCA
B144_0021GC
LOWER
TRANSPORT AY
To Install:
1 Insert the EXIT ROLLER through the BELT.
2 Reverse the steps in the removal procedure.
Postrequisites:
None
EXIT ROLLER
Replacements
To Remove:
LATCH
UPPER TRANSPORT AY
Warning
Dangerous Voltage
1 De-energize the equipment.
2 Disconnect the main power.
3 Remove the EXIT TRAY.
4 Release the LATCH.
5 Lift the UPPER TRANSPORT AY to the
service position.
B144_0036ACB
B144_0036AC
DRIVE COVER
B144_0040ACA
B144_0040AC
INPUT TRAY
Replacements
12SEP02
AR3177-1
Page
27 of 37
BELT
DRIVE BELT
B144_0038ACA
B144_0038AC
COVERS
E-RING
WASHER
B144_0030GCA
B144_0030GC
BEARING
ROLLER
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
Replacements
TAKE-AWAY ROLLER
Prerequisites:
1 Remove:
FEED MODULE
LOWER TRANSPORT AY
To Remove:
DRIVE COVER
B144_0040ACA
B144_0040AC
Replacements
12SEP02
AR3177-1
Page
30 of 37
J/CLUTCH
CONNECTOR
B144_0045GCA
B144_0045GC
LOWER TRANSPORT AY
Replacements
2 BELTS
2 BELTS
ROLLER
BEARING
WASHER
E-RING
E-RING
WASHER
BEARING
TAKE-AWAY ROLLER
B144_0031ACA
B144_0031AC
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
To Remove:
Warning
Dangerous Voltage
1 De-energize the equipment.
2 Disconnect:
IEEE 1394 INTERFACE
POWER CABLE
IEEE 1394 INTERFACE
POWER CABLE
B144_0035ACA
B144_0035AC
LATCH
UPPER
TRANSPORT AY
EXIT TRAY
B144_0025ACA
B144_0025AC
Replacements
CABLE
P/J601
a Disconnect P/J601.
b Remove the CABLE.
Warning
B144_0033GCA
B144_0033GC
To Install:
1 Reverse the steps in the removal procedure.
Postrequisites:
None
Replacements
To Remove:
200 BOARD
4 PINS
ESD
Possible damage from electrostatic discharge.
P/J206
P/J207
P/J10
B144_0048GCA
B144_0048GC
100 BOARD
Replacements
2 SCREWS
2 SPRINGS
2 Remove:
2 SCREWS
2 SPRINGS
GUARD
SUPPORT
200 BOARD
2 VIDEO CABLES
SUPPORT
GUARD
B144_0044GCA
B144_0044GC
Continue with
Step 6 to remove
the existing parts
from the old 100
BOARD.
No
No action
4 PINS
Replacements
100 BOARD
256 MB
No action
600 BOARD
B144_0047GCA
B144_0047GC
To Install:
Important
Postrequisites:
None
Replacements
12SEP02
AR3177-1
Page
37 of 37
Kodak is a trademark.