80%(5)Il 80% ha trovato utile questo documento (5 voti)
1K visualizzazioni16 pagine
You can test point by point manual change Advanced distance you can adjust ramp of testing points 1 / 14 u can make right click and test the point this menu will appear Or u can write the value here and test 2 / 14 here u can adjust the setting for your test Prefault a!" fault current 3 / 14 Advanced distance #hot if u want to make one point test $heck : for %one reach and timing test Press parameter'hardware configuration 4 / 14 Press general ( detail ( check
You can test point by point manual change Advanced distance you can adjust ramp of testing points 1 / 14 u can make right click and test the point this menu will appear Or u can write the value here and test 2 / 14 here u can adjust the setting for your test Prefault a!" fault current 3 / 14 Advanced distance #hot if u want to make one point test $heck : for %one reach and timing test Press parameter'hardware configuration 4 / 14 Press general ( detail ( check
You can test point by point manual change Advanced distance you can adjust ramp of testing points 1 / 14 u can make right click and test the point this menu will appear Or u can write the value here and test 2 / 14 here u can adjust the setting for your test Prefault a!" fault current 3 / 14 Advanced distance #hot if u want to make one point test $heck : for %one reach and timing test Press parameter'hardware configuration 4 / 14 Press general ( detail ( check
Normal distance: you can test point by point manual change
Advanced distance you can adjust ramp of testing points 1 / 14 U can make right click and test the point this menu will appear Or u can write the value here and test 2 / 14 Here u can adjust the setting for your test Prefault a!" fault current 3 / 14 Advanced distance #hot if u want to make one point test $heck : for %one reach & timing test Press parameter ' hardware configuration 4 / 14 Press general ( detail to check the connection Press test opject 5 / 14 )nter your system data * +,P * -ou can select the direction for your test 6 / 14 #elect %one setting .o add new %one click new then edit #elect the type of your char" .hen enter the setting 7 / 14 $lick default setting and adjust the current / 0A then click O1 8 / 14 Press se2uence and enter your re2uired ramps start & stop 3 step 9 / 14 RELAY MIN. PICKUP CURRENT OP)N A4+"4,#.AN$) #$5))N #elect setting and change the fault current 3 6o to shot screen #elect impedance 3 click single test 10 / 14 High set #tate se2 " ake the first state ((((( healthy 78"9 for 8 ph & :A for 8 ph time 0 sec " .he sec" state +5 / ;:+ and other phases healthy time 0 sec .he third state change the value for ,5 around H# value/0,n then test ust adjust measurement view start at state 8 & stop at trip 11 / 14 0 nd method cb trip <= 3 ,> #O.> enable must A$ #O.> pick delay/; sec" ,N?)$. one state : voltage for all phases & ;:A ,5 3 ,#/,./:
12 / 14 #O.> A4+" 4,#.AN$) 3 make 4,#.AN$) fun" )nable A$ #O.> 6o to setting screen and adjust pre fault time case A/;9:msec case @ /09: msec " And after this test impedance from shot screen and sheck #O.> A)4 $ase A : #O.> OP)5A.) $A#) @ : #O.> NO. OP)5A.) 13 / 14 4$ #O.> 6o to #)<U)N$)5 screen #tate ;: 78"9 + & : A for all phases #tate 0 : fault state: +5/;:+&+#/78"9& +./78"9 & ,5/9A& ,#/: & ,./: and change the time for state ; case A/89:msec case @ /B9: msec and apply Cve to A07 $@ $AO#) through @O from Omicron click here and select @O:; for state ; & state 0 14 / 14 .est the two cases and check #O.> A)4 $ase A : #O.> OP)5A.) $A#) @ : #O.> NO. OP)5A.) VTS (voltage transforer s!"erv#s#on ( #etting +res"/0: v & ,res" / ;"9 A by using 2uick cmc inject this values +5/+#/+./78"9 + AN4 @AAAN$)4 3 current / : for all phases 4ecrease the value of +r to B8"9 + the led for +.# will be appeared ,ncrease ,5 UP .O ;"9 A the led will be disappeared 3 for phase #&. repeat the above state 15 / 14 @locking function ,nject 8 states like this : ; ( healthy state vr/vs/vt /78"9 v & balanced 3 ,r/,s/,t /: & time /0 sec 0 ( drop the voltage of ph" 5 to ;:+ and remain the others phases like state ; time / 0 sec 8 ( increase the value of current ,r to 7A .he relay not trip