Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
42LE5500
LED Backlights
OUTLINE
Preliminary Section: Contact Information, Preliminary Matters, Specifications, LCD Overview, General Troubleshooting Steps, Signal Distribution, Disassembly Instructions and Voltages Disassembly Section: Removal of Circuit Boards Troubleshooting Section: Board Operation Troubleshooting of : Switch Mode Power Supply with LED Backlight Driver Board Main Board Ft Control Board Soft Touch Keys Speakers
At the end of this Section the Technician should be able to Identify the Circuit Boards and have the ability and knowledge necessary to safely remove and replace any Circuit Board or Assembly.
CAUTION
To avoid personal injury, disconnect the power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be aware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.
ESD Notice
Todays sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti-static bag to a ground connection point or unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.
Regulatory Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.
LG Contact Information
Customer Service (and Part Sales) Technical Support (and Part Sales) USA Website (GSFS) Customer Service Website Knowledgebase Website LG Web Training LG CS Academy (800) 243-0000 (800) 847-7597
http://136.166.4.200
LCD-DV: 32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90, 42SL80, 47LG90, 47LH85, 42LE5500, 47LE8500 PLASMA: 42PG20, 42PJ350, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK250, 50PK750, 50PS80, 50PS60, 60PK750, 60PS11, 60PS60, 60PS80 Also available on the Plasma Page: PDP Panel Alignment Handbook, Schematics with Bookmarks Plasma Control Board ROM Update (Jig required) New Training Materials on the Learning Academy site
Published September 2010 by LG Technical Support and Training LG Electronics Alabama, Inc. 201 James Record Road, Huntsville, AL, 35813.
This section of the manual will discuss the specifications of the 42LE5500 LCD Direct View Display
9 October 2010 LCD TV 42LE5500
Wireless Receiver/Transmitter Dongle Attaches via Velcro to the back of the set HDMI
10
Wireless Router
11
Basic Specifications
Key TV Features
LED Plus w/Local Dimming NetCast Entertainment Access* (Wi-Fi Ready) Wireless 1080p Ready* DLNA Certified TruMotion 120Hz Full HD 1080p Resolution 5M:1 Dynamic Contrast Ratio Picture Wizard II (Easy Picture Calibration) Smart Energy Saving ENERGY STAR Qualified Intelligent Sensor AV Mode II (Cinema, Sports, Game) Clear Voice II ISFccc Ready 24P Real Cinema USB 2.0 (JPEG, MP3, DivX HD) DivX HD 4 HDMI V.1.3 w/Deep Color SIMPLINK Connectivity Dolby Digital 5.1 Decoder Infinite Sound
12
Prepare to be dazzled. Tired of dark scenes or dull colors? LGs LED Plus technology provides even greater control of brightness through local dimming to deliver amazing clarity and color detail, as well as a more energy efficient TV compared to conventional TVs.
TruMotion 120Hz See sports, video games and high-speed action with virtually no motion blur and in crystal clarity with LGs TruMotion 120Hz technology. Now your TV can keep up with the fastest moving scenes.
NetCast
Entertainment on tap. NetCast Entertainment Access brings the best Internet services direct to your TVno computer required. Instantly access movies and TV shows, news and weather and the worlds largest library of HD movies in 1080p.
13
14
Save Energy, Save Money It reduces the plasma displays power consumption. The default factory setting complies with the Energy Star requirements and is adjusted to the comfortable level to be viewed at home. (Turns on Intelligent Sensor).
Save Energy, Save Money Home electronic products use energy when they're off to power features like clock displays and remote controls. Those that have earned the ENERGY STAR use as much as 60% less energy to perform these functions, while providing the same performance at the same price as less-efficient models. Less energy means you pay less on your energy bill. Draws less than 1 Watt in stand by.
15
Intelligent Sensor The Intelligent sensor will monitor the room lighting environment. When the room lights go out, the TV will automatically adjust the picture for the best view enjoyment.
16
BOTTOM PORTION
17
To access the Service Menu. 1) You must have either Service Remote. p/n 105-201M or p/n MKJ39170828 2) Press In-Start 3) A Password screen appears. 4) Enter the Password.
Note: A Password is required to enter the Service Menu. Enter; 0000 Note: If 0000 does not work use 0413.
105-201M
MKJ39170828
18
USB1 or USB2 for Software Upgrades, Wireless Dungle, Music and Photos
Side In/Out
USB 2
LAN USB 1
Head Phones
19
Bring up the Customers Menu then Press the Red button on Remote With Software Update Highlighted, Press Select on Remote
Continue on next page
20
If you select Yes; Service call number, Model name, SW version and serial No. is displayed. Note: Confirm the Suffix of the model number. If the Main board is replaced, the Model and Serial number must be reinserted into memory. See Model Number D/L.
21
2) Copy new software (xxx.epk) to "LG_DTV" folder. Make sure to have correct software file. 3) With TV turned on, insert USB flash drive. 4) You can see the message TV Software Upgrade (See figure to right) 5) Cursor left and highlight "START" Button and push Enter button using the remote control. 6) You can see the download progress Bar. 7) Do not unplug until unit has automatically restarted. 8) When download is completed, you will see COMPLETE. 9) Your TV will be restarted automatically.
* CAUTION: Do not remove AC power or the USB Flash Drive. Do not turn off Power, during the upgrade process. Software Files are now available from LGTechassist.com
22
Highlight the Software update file and press SELECT to begin the download process. WARNING: Use extreme Caution when using the Manual Forced Download Menu. Any file can be downloaded when selected and may cause the Main board to become inoperative if the incorrect file was selected.
23
24
5) Downloading Complete
Note: When PCM is downloaded, AC3 will be N/G and when AC3 is downloaded PCM will be N/G. This means that when PCM is OK, PCM audio is priority and when AC3 is OK, AC3 audio is priority.
25
7.7/8" 200mm
24.13/16" 629.92mm
Center
27.3/16" 690.88mm 12.3/8" 314.96mm 11.5/16" 288mm Remove 4 screws to remove stand for wall mount
2.3/8" (60.96mm)
20.7/16" 510mm
10.5/8" 269.24mm
26
October 2010
42LE5500
LCD-DV
DISASSEMBLY SECTION
Disassembly: This section of the manual will discuss Disassembly, Layout (Circuit Board Identification) of the 42LE5500 LCD Direct View Television. Upon completion of this section the Technician will have a better understanding of the disassembly procedures, the layout of the printed circuit boards and be able to identify each board.
27
Remove the 28 screws indicated. Pay attention to the size and type of screw as there are many different types. Putting in an improper screw when reassembling may Cause damage.
The AC Cord Does Not unplug Remove plastic cover.
The Stand Bracket has a plastic cover Not Shown that must be removed to expose the screws. The Stand has to be removed before removing the back.
28
Clips hold the front glass in place, use caution. Add screws while servicing.
To LEDs
Main Board
LVDS Cables
IR/LED Board
LG Logo Board
29
If the Panel is replaced, reset the UTTTime. Service Menu, System 1 Item 12
P205
P201
POWER SUPPLY
p/n: EAY60803101 p/n: EAY60803201
P7501 P7500
P8000
n/c n/c
MAIN BOARD
p/n: EBU60904603 p/n: EBR66101301 p/n: EBU60904602
SK101
P8800 P8200
AC In
J2 J3
J1
To TFT Panel
IR
p/n: EBR64966201
LED
p/n: EAV60793302
30
October 2010
42LE5500
LCD-DV
p/n EAY60803101
P204 P205
P201
P201
31
Flip the locking tab upward, pull the LVDS ribbon out.
P7501
P7500 P8000
Remove any tape holding down any cables. Remove the 7 screws indicated by the arrows.
N/C
N/C
Decorative Metal Plate After removing the Main, there are tabs sticking through the Main board holding the Metal plate in place. P8800 P8200
NOTE: Always check on top and behind the Large ICs. And look for a piece of Chocolate (Heat Transfer Material). Be sure to transfer to new Board if present.
32
Tab Tab
J2
J3
Tab
33
TROUBLESHOOTING SECTION
Troubleshooting: This section of the manual will discuss troubleshooting. Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems.
34
35
p/n EAY60803101 F101 3.15A/250V F103 1A/250V STBY 7.6V Run 396V From Hot Gnd
36
1
No AC Det in this model
120V
Local and Global Dimming
Bridge
On Board Inverter
8 9 9 9
P205
6 8
12V/24V Regulators
120V
Local and Global Dimming
LCD PANEL To Panel Backlights 120Hz Manipulates Backlight LEDs Low = Bright
RL_ON
P-DIM
2
P8000
3.5V_ST 2 5 Other Regs
9~12
5
1
6
17 19 21
6
2~4
8
18
9
22
Globar Dimming 7
IC9302 1.8V_L/ Dimming
9
23
Inverter On
MAIN BOARD
RL_On Power On
P-DIM
IC9301 Dimming IC
Q8004
Panel VCC 12V
IC9103
DC to DC
12V
Note 1: 12V TURNS ON: IC8000 5V_USB IC8003 5V_Normal IC8005 3.3V_Normal IC8903 +3.3V_MEMC IC8902 +1.26V_MEMC MEMC= Motion Estimated Motion Compensated For Video Processor
8 INV_CTL 7 4 9
IC9102 HVDD
Power RL_ON On
7.8V
VCC 3.3V, VDD 16V, VGL -5V, VGH 26V, 7 HVDD 7.8V P7500 P7501 After Mute Released LVDS Video 9 And Tru-Motion LVDS Video
P8200
Ft IRKey
October 2010
42LE5500
LCD-DV
R8003 22K R8010 10K 11.8V 1.8V 11.8V 3.36V R8060 10K
Panel_Vcc (12V)
11.79V L8015
Q8004
+12V L8000
S G
Q8003
0.68V
Q8001
0V
R8001
47K
R8103
100
SMPS P201
PWR 24V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 3.36V 21.27V 21.27V 21.27V Gnd Gnd Gnd Gnd 3.5V 3.5V 3.5V 3.5V Gnd Gnd Gnd 0.02V 11.43V 3.28V 11.43V 0.09V 11.43V 0.38V~3.3V 3.3V Gnd
7
3.36V
IC8005
2 6
+12V 20 R8176
22K Power On/Off 2_2
PWR-ON +24V
L8005
Power_On/Off2_2
IC8101 Micro
IR
16
3.3V
Q8002
0V
Q8000
0V 4.7K
0.66V
R8004
R8000
10K
RL_ON
36 RL_ON R8187
22
SBY3.5V
L8003
3.36V
Model_Opt_1 11
R8135 40
Reset Power Det 14 Key 1 25 Key 2 26 22
R8026
1K 3.1V
VSYNC 12V INV_CTL 12V SCLK 12V PWM-DIM SIN ERR OUT
16 17 18 19 20 21 22 23 24
+3.3V_Normal
Q8005
0V
INV_On R8019
100
10 R8032
10K
INV_CTL
PWM-DIM (PWM Dimming) can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). 3.76V p/p Range 0.37V to 3.3V. (Data) 3.25V p/p Data
3.64V p/p
IC900 BCM
U5
M2_SCLK M2_MOSI
R9346 22
IC9301
R6 Dimming T6
R9347 22
38
October 2010
42LE5500
LCD-DV
(1) Add a jumper between (3.5V STBY) pin 7, 8, 9 or 10 and Pin 1 (PWR_ON). Apply AC. This will turn on the power supply, relays will click. a) Check that the 24V and 12V power supplies are turned on, P201 (12V pins 17, 19 and 21) P201 (24V pins 2, 3 and 4) P204 and P205 (120V pins 1 and 12) to the Panel. (Or check D206 + lead) (2) Remove AC power
39
40
E
B
P204
120V n/c *1V~30V LED Drive n/c *1V~30V LED Drive n/c 120V
E
B
C C C C C
E B E B E B E
B
P205
120V n/c *1V~30V LED Drive n/c *1V~30V LED Drive n/c 120V *White 100 IRE to Black 0 IRE
E
B
E B E B E
B
C C C C
Gnd
Pin 16 P201
E B E
Pin 23 P201
3.25V p/p
100uSec
These drivers ground the LED blocks. (12 Total). If the 120V is present on Pins 1 and 12 of P204 and P205 you can ground these test points to turn on a block.
3.25V p/p
100uSec
41
October 2010
42LE5500
LCD-DV
P201 Label
P201 Connector
*Pin 24 is grounded on the Main Board Diode Mode values taken with all Connectors Removed
42
P204
Diode Check Open Open Open Open Open Open Open Open Open Open Open
Label 02.A n/c 02-1C 02-2C 02-3C n/c 01-3C 01-2C 02-1C n/c 01.A
Run 120V n/c 1V~30V 1V~30V 1V~30V n/c 1V~30V 1V~30V 1V~30V 0V 120V
Run 120V n/c 1V~30V 1V~30V 1V~30V n/c 1V~30V 1V~30V 1V~30V 0V 120V
1
P205
The drive signal changes due to the brightness level of the backlights. Low indicates Bright. High indicates Dim.
43
Power Supply Connector SK101 and AC Fuses Voltage and Diode Check
F102 1A/250V AC F100 6.3A/250V AC IN SK101 "SMPS" to AC IN Pin EL1 EL3 Label L N STBY Run Diode Check OL OL
F102
F100
120Vac
AC Voltage Readings (From Hot Ground) Pins 1 and 2 for STBY and RUN.
Diode Mode values taken with all Connectors Removed
F100 or F102 (Diode Check) Main Power Switch Closed Red or Black Lead on Fuse (Open) Other Lead on Hot Ground
If the set was on and then turned off into the Stand-By condition, the voltage takes a very long time to bleed down to the reading given here.
45
The Main board also develops several B+ sources on the board. STAND-BY VOLTAGES 3.3V_ST (Voltage direct from SMPS). LVDS Panel_VCC (12V Not generated, but switched from the 12V arriving from the SMPS). TUNER and VSB CIRCUIT 3.3V_TU (Made from 3.3V_Normal). 1.26V_TU (Made from 3.3V_TU). WIRELESS VOLTAGES to JK8700 20V (Switched from 20V from SMPS) AUDIO IC8801 1.8V (Made from 3.3V_Normal).
GENERAL 5V_Normal (Made from 12V In). 3.3V_Normal (Made from 12V In). 5V USB (Made from 12V In). BCM IC900 Micro/Video Processor 3.3V_ST, 1.2V, D1.5V, D1.8V IC9301 Tru-Motion and Dimming IC 1.26V_MEMC, 1.5V_MEMC, and 3.3V_MEMC T-CON IC9001 3.3V_VCC, -5V_VGL, 27V_VGH, 16V_VDD and HVDD (7.8V) HDMI VOLTAGES (Q200) 1.8V_HDMI (From D1.8V)
46
To Panel P8000 To SMPS VIDEO PROCESSOR IC900, T-CON IC9001 and Tru-Motion IC9301 runs Hot. This is normal.
P7500
P9000 n/c
USB 1
P8100 n/c
IC900
USB 2 Component In
These connectors are Mini plug type
Headphone HDMI
47
Q
E
D
X9300 25Mhz IC9300
P7501
A1 A2
IC8005
SW9300
D9102 L9301
IC9302
L8015
Q8007 IC8003
X9000 12Mhz
IC8900
X8100
IC8101
Micro
IC901 L8004
USB1
Q8800
IC8804
IC8800 IC8801 L8804 L8805 Q? Q8700 Q8200 Q8201 P8800 P8200 IC8300
Component Composite
HP HDMI
A2
A1
D8310
48
October 2010
42LE5500
LCD-DV
IC300 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC301 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC302 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q300
Earphone Amp 0V 0V 0V 0V 0V 3.3V 3.3V (-1.8V) (-0.8V) Gnd 0.9V 1.8V 3.3V 3.3V Gnd 0V Switched 5V for USB 2 Gnd 5V (In) 5V 3.3V 3.3V 5V (Out) 5V (Out) n/c Switched 5V for USB 1 Gnd 5V (In) 5V 3.3V 3.3V 5V (Out) 5V (Out) n/c
IC700
(+1.26V_TU) Pin Regulator [1] 0V (Gnd) [2] 1.26V (Out) [3] 3.3V (In) SOC Reset Pin Generator [1] 3.32V (In) [2] 0V (Gnd) [3] 3.3V (Out) 5V Regulator for USB 11.79V (In) 5V (Out) 5V (Out) 10.5V 3.3V 0.8V 4.99V 0V (Gnd) D1.2V and A1.2V Regulator 0V (Gnd) 3.3V 0V (Gnd) 1.2V 3.3V n/c 4.46V 3.3V 3.3V 3.3V 1.2V Gnd 3.3V 0.8V
IC8002 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC8003 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8004 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q8005
(D1.8V) Regulator 5V 3.34V (In) 1.8V (Out) Gnd Gnd 0.9V 0.9V 1V 2.38V 3.36V (PWR On/Off1 Ctl) (+5V_NORMAL) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.86V 3.37V (PWR On/Off2 Ctl) 5V (In) 5V (In) A2.5V Regulator for USB n/c 3.26V (In) 3.26V (In) n/c n/c 2.55V (Out) 0.8V 0V (Gnd)
IC8005 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8007
IC1000
(+3.3V_NORMAL) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.86V 3.36V (PWR On/Off2 Ctl) 3.36V (Out) 3.36V (Out)
IC8902 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8903 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC9100
(+1.26V_MEMC) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.7V 3.36V (PWR On/Off2 Ctl) 1.3V (Out) 1.3V (Out) (+3.3V_MEMC) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.8V 3.36V (PWR On/Off2 Ctl) 3.3V (Out) 3.3V (Out) P-GAMMA Chip 3.3V 0V (Gnd) 3.3V (In) 0V (Gnd) 6.8V 6.8V 15.3V 15.3V n/c 13.47V 12.75V 11.8V 10V 5.96V 4.06V 15.3V 0V 2.96V 2.33V 3.3V (In)
IC9102 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC9300
IC8000 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8001 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14]
Power Det Gen Pin (+12V and +3.5V) [1] 0V (Gnd) [2] 3.6V (In) [3] 3.5V (Out) Power Det Gen Pin (+24V) [1] 0V (Gnd) [2] 3.6V (In) [3] 3.7V (Out) (+1.8V_AMP) Regulator 0V (Gnd) 1.8V (Out) 3.295V (In)
IC8008
DC to DC HVDD T-CON 0V (Gnd) 11.72V (In) 11.72V (In) 3.25V 3.2V 0V 0V 11.7V 0V (Gnd) 1.13V 0V (Gnd) 0V (Gnd) 0V (Gnd) 7.7V 7.7V (HVDD) 0V (Gnd)
(+1.5V_MEMC) Pin Regulator [1] 0V (Gnd) [2] 1.5V (Out) [3] 3.3V (In) HDMI Det
INV_ON Pin Driver B 0V (INV ON) En C 3.1V (Out) E Gnd IR Buffer 2nd
PANEL_VCC
Control 2nd Driver
HDMI Det
0.679V 0V Gnd
Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]
Reset for Pin LG5111 [1] 3.32V (In) [2] 0V (Gnd) [3] 3.34V (Out) (1.8V_L/Dimming) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.76V 3.34V (PWR On/Off2 Ctl) 1.8V (In) 1.8V (In)
IC9302 Pin [1] [2] [3] [4] [5] [6] [7] [8] D9101
VGH/VDD Pin Rectifyer A 15.4V AC 22.2V C 27.4V (VGH) VGL/VCC Pin Rectifyer A (-5V VGL) AC (-1.9V) C 0V
D9102
Q8001
0V 0.68V Gnd
IR Buffer 1st
Q8700 Wireless PWR Dongle Out Turns on Q8701 B 0.66V (0.0V Dongle In) C 0.14V (24V Dongle In) E Gnd
Q8800
49
October 2010
42LE5500 LCD-DV
Q
E
D
Q8002
3 1 2
Rubber
A1 A2
Rubber Q8000
IC9001
IC9003
IC9000
Q901
IC8100 D8312
D G S B
Q8308
Q200
G
Digital Video
18. IF p 17. IF n 16. IF AGC 15. Reset 14. 3.3V 13. 1.26V 12. GND 11. CVBS 10. NC 9. SIF 8. NC 7. SDA 6. SCL 5. NC 4. NC 3. 5V 2. NC 1. NC
Q8304 IC8400
Q701
50
October 2010
Rubber
TU700 TDVJ-H031F
S D
42LE5500
LCD-DV
IC602 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8100 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8200 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16]
D1.8V Regulator 0V (Gnd) 3.29V (PWR On/Off1 Ctl) 0.9V (DDR_VTT) 0.93V 1.83V 3.38V (In) 1.8V (Out) 0.91V (DDR_VTT) EEPROM Micro 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 0V (Gnd) 3.37V RS232 Routing 0V 0V 0V 0V 0V (-5.47V) n/c (5.59V) n/c (0V) n/c (3.3V) n/c (0.2V) n/c (3.3V) 3.35V 0V (-5.47V) 0V (Gnd) 3.37V
IC8400 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] IC8401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC9000 Pin [1] [2] [3] [4] [5] [6] [7] [8]
RGB H/V Sync 1.9V 1.9V 4.4V 0V 0.9V n/c (4.5V) 0V (Gnd) n/c (4.5V) n/c (1.9V) n/c (1.9V) n/c (4.5V) 0.9V 0.9V 5V EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 0.7V 4.1V 4.5V 4.5V (In) Serial Flash T-CON 0.06V 0.67V 3.3V (In) 0V (Gnd) 0V 0.34V 3.31V (In) 3.34V (In)
IC8700 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC9303 Pin [1] [2] [3] [4] [5] [6] [7] [8]
Wireless Buffer 0V (3.3V Dongle In) 3.3V (0.3V Dongle In) n/c n/c n/c Gnd Gnd Gnd n/c 0.02V 0V 3.3V 0V (3.3V Dongle In) 3.3V 3.3V 3.3V EEPROM for LG5111 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 3.34V 3.37V (In)
Q200
(1.8V_HDMI) Pin Switch S 1.83V (Out) G 3.35V (PWR On/Off2 Ctl) D 1.83V (In) Tuner SIF Pin (Sound) Buffer B 0.16V C Gnd E 0.83V Tuner Video Pin (Analog) Buffer B 2.05V C 2.75V E Gnd FLASH_WP Pin for IC901 B 0V (Flash_WP) C 3.36V E Gnd RL_ON (PWR_On) Pin 1st Driver B 0.66V C 0V E Gnd PWR_ON Pin Switch [1] 3.36V (In) [2] 0V [3] 3.3V (Out)
Q8203
Q701
Q8205
Q702
Q8300, 2 HDMI 2 Pin Det B 4.2V C 0V E Gnd Q8303, 4, 5 HDMI 3 Pin Det B 0V C 4.2V E Gnd Q8308 Pin [B] [G] [S] [D] Q8701 CEC Remote HDMI CEC 2.72V 2.73V 3.27V 3.37V
Q901
Q8000
Q8002 D8306, 7, 9 5V Pull Up Routing Pin HDMI SCL/SDA A1 5.04V C 4.58V A2 0V D8312 3.5V Pull Up Pin HDMI CEC A1 0V C 3.26V A2 3.2V
IR Wireless Pass Pin 2nd Driver G 24.5V (2.3V Dongle I S 24V D 0V (24.5V Dongle In)
51
October 2010
42LE5500 LCD-DV
X9000 1.56V
2.54V p/p
3.27V p/p
12Mhz
1.6V
X9001 X9000
MAIN Board
52
Either leg
789mV p/p
54Mhz
Runs when set is On
1.3V
1.85V p/p
2.82V p/p
MAIN Board
1.5V
1.75V
53
+7.81V HVDD
L9100
+16V VDD
L9102
+3.3V VCC
54
From IC9101 Pin 21 -4.8V (VDD-ODD) From IC9101 Pin 19 -4.7V (VST) From IC9101 Pin 20 -4.8V (VDD-EVEN)
55
Main Board Connector P8000 to Power Supply Voltage and Diode Check
P8000
P8000 Main Board" to P201 SMPS" Pin 1 2-4 5-8 9-12 13-15 16 Diode Mode values taken with all Connectors Removed 17 18 19 20 21 22 23 24 Label PWR-ON 24V Gnd 3.5V Gnd V-SYNC 12V INV-ON 12V SCLK 12V P-DIM L-DIM (SIN) ERROR STBY 0V 0V Gnd 3.57V Gnd 0V 0V 0V 0V 0V 0V 0V 0V Gnd Run 3.36V 21.27V Gnd 3.5V Gnd 0.02V 11.43V 3.28V 11.43V 0.09V 11.43V 0.38V~3.3V 3.3V Gnd Diode Check Open Open Gnd 1.24V Gnd 1.06V Open 1.62V Open 1.06V Open Open 1.05V Gnd
(1)
PDIM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and Intelligent Sensor (room light condition). Range 0.37V to 3.3V.
56
Main Board Connector P7500 to the Panel Voltage and Diode Check
P7500 Connector Main" to the Panel
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label Gnd GMA1 GMA3 GMA4 GMA6 GMA7 GMA9 GMA10 GMA12 GMA13 GMA15 GMA16 GMA18 Gnd OPT_N H_CONV VST_IN POL SOE Gnd Run Gnd 14.91V 13.5V 12.78V 11.88V 10.02V 8.02V 7.48V 5.99V 4.08V 2.98V 2.35V 1.06V Gnd 1.06V 1.07V 0V 0.62V 0.3V Gnd Diode Check Gnd Open Open Open Open Open Open Open Open Open Open Open Open Gnd 2.06V Gnd 1.06V 1.06V 1.06V Gnd Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label LV0+ LV0LV1+ LV1LV2+ LV2LVCLK+ LVCLKLV3+ LV3LV4+ LV4LV5+ LV5Gnd VCC VCC Gnd HVDD HVDD
There are no Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
Run 1.06V 1.27V 1.4V 1.3V 1.03V 1.3V 1.16V 1.17V 1.07V 1.27V 1.02V 1.3V 1.02V 1.3V Gnd 3.3V 3.3V Gnd 7.81V 7.81V Diode Check 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V Gnd 1.64V 1.64V Gnd Open Open Pin 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Label VDD VDD Gnd VCOM_IN VCOM_FB Gnd VST VGL VDD_EVEN VDD_ODD VGI_P (VGL) VGI_N (VGH) CLK6 CLK5 CLK4 CLK3 CLK2 CLK1 Z_OUT Gnd Run 15.57V 15.57V Gnd 6.86V 6.87V Gnd (-4.7V) (-5V) (-4.8V) (-4.8V) (-5V) 27.4V 8V 8V 8V 8V 8V 8V 7.7V Gnd Diode Check Open Open Gnd Open Open Gnd 1.5V 0.6V 1.5V 1.5V 0.6V Open 1.5V 1.5V 1.5V 1.5V 1.5V 1.5V Open Gnd
57
Main Board Connector P7501 to the Panel Voltage and Diode Check
P7501 Connector Main" to the Panel
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Label Gnd Z_OUT CLK1 CLK2 CLK3 CLK4 CLK5 CLK6 VGH VGH VGH_ODD VGH_EVEN VGL VST Gnd VCOM_FB VCOM_IN Gnd VDD VDD Run Gnd 7.7V 8V 8V 8V 8V 8V 8V 27.4V (-5V) (-4.8V) (-4.8V) (-5V) (-4.7V) Gnd 6.87V 6.86V Gnd 15.57V 15.57V Diode Check Gnd Open 1.5V 1.5V 1.5V 1.5V 1.5V 1.5V Open 0.6V 1.5V 1.5V 0.6V 1.5V Gnd Open Open Gnd Open Open Pin 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Label HVDD HVDD Gnd VCC VCC Gnd RV0+ RV0RV1+ RV1RV2+ RV2RVCLK+ RVCLKRV3+ RV3RV4+ RV4RV5+ RV5-
There are no Stand-By Voltages for the Connector Diode Mode values taken with all Connectors Removed
Run 7.81V 7.81V Gnd 3.3V 3.3V Gnd 1.07V 1.12V 1.13V 1.23V 1.13V 1.22V 1.17V 1.18V 1.08V 1.27V 1.12V 1.22V 1.13V 1.22V Diode Check Open Open Gnd 1.64V 1.64V Gnd 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V 1.09V 0.9V Pin 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Label Gnd SOE POL VST_IN H_CONV OPT_N Gnd GMA18 GMA16 GMA15 GMA13 GMA12 GMA10 GMA9 GMA7 GMA6 GMA4 GMA3 GMA1 Gnd Run Gnd 0.3V 0.62V 0V 1.07V 1.06V Gnd 1.06V 2.35V 2.98V 4.08V 5.99V 7.48V 8.02V 10.02V 11.88V 12.79V 13.5V 14.91V Gnd Diode Check Gnd 1.06V 1.06V 1.06V Gnd 2.06V Gnd Open Open Open Open Open Open Open Open Open Open Open Open Gnd
58
Main Board P8200 to (Ft. IR/Intelligent Sensor) Voltage and Diode Check
P8200 Connector "MAIN Board" To P100 "IR Board" Pin 1 2 3 4 5 6 7 8 9 10 11 12
(1) Clock (2) IR
P8200
Label
(1) (1)
STBY 3.56V 3.56V Gnd 3.32V 3.29V 3.56V Gnd 0V 1.63V Gnd 0V 0V
Run 3.5V 3.5V Gnd 3.3V 3.3V 3.47V Gnd 0V 1.6V Gnd 3.34V 0V
Diode Check Open Open Gnd 1.9V 1.9V 1.24V Gnd Open Open Gnd 0.52V Open
SCL SDA
IR
pulses only present when Intelligent Sensor is turned on. (3.7V p/p) pulses (1.6V p/p)
59
Use speaker out to test for defective Audio Amp IC8801 Note: (Normal, Audio B+) P8800 CONNECTOR "Main" to "Speakers" Pin 1 2 3 4 LABEL SPK-R(-) SPK-R(+) SPK-L(-) SPK-L(+) SBY 0V 0V 0V 0V Run 10.62V 10.62V 10.62V 10.62V Diode Check Open Open Open Open
Mute Pin 25
IC8801
Audio B+ 21.3V Pins 49-52
(1)
Main JK8700 Wireless Media Box Dongle Jack (Voltage and Diode Check)
JK8700 "MAIN Board" To "Wireless Media Box Dongle"
Pin 1-6 7 8 9 10 11 12 13 14 15 16 17 18 19-20 Label *20.3V Detect Interrupt Gnd n/c Gnd I2C_SCL I2C_SDA Gnd Wireless_RX Wireless_TX Gnd IR Gnd STBY 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0.67V 0V Run 20.3V 0.3V 3.3V Gnd 3.3V Gnd 3.3V 3.3V Gnd 3.3V 3.3V Gnd 3.3V Gnd Diode Check 0.98V 0.98V 1.2V Gnd 1.1V Gnd 1.02V 1.02V Gnd 1.17V 1.22V Gnd 1.37V Gnd Diode Mode values taken with all Connectors Removed 1
Wireless Media Box Dongle must be plugged in for these voltages. JK8700 Jack
Voltages with Wireless Media Box Dongle plugged in. Use Media Box Dongle side to read voltages. Remove cover, (see Wireless Media Box training manual for details). *20.3V Switched from Q8701 Drain Back side of the board. Q8701 turned on by Q8700 front side of the board. Q8700 turned on by Microprocessor pin 38.
61
62
(1)
J1 To Main Board
63
Front Board Connectors CON1, CON2 and CON3 Voltage and Diode Check
CON1 "Front IR" to P8200 " MAIN" Pin 1 2 3 4 5 6 7 8 9 10 11 12
(1)
CON2 "Front IR" to Soft Touch Key Board" Diode Check Open Open Gnd 1.9V 1.9V 1.24V Gnd Open Open Gnd 0.52V Open CON3 "Front IR" to LG Logo Board" Pin 1 2 3 4 STBY 3.56V Gnd 1.36V Gnd Run 3.47V Gnd 0.6V Gnd Diode Check 1.24V Gnd Open Gnd Pin 1 2 3 4 5 6 7 8 STBY 3.56V 0V Gnd 3.56V 3.56V Gnd 3.32V 3.29V Run 3.47V 1.63V Gnd 3.5V 3.5V Gnd 3.3V 3.3V Diode Check Open Open Gnd Open Open Gnd 1.9V 1.9V
Label
(1) (1)
STBY 3.56V 3.56V Gnd 3.32V 3.29V 3.56V Gnd 0V 1.63V Gnd 0V 0V
Run 3.5V 3.5V Gnd 3.3V 3.3V 3.47V Gnd 0V 1.6V Gnd 3.34V 0V
SCL SDA
IR
Clock pulses only present when Intelligent Sensor is turned on. (3.7V p/p) (2) IR pulses (1.6V p/p) Diode Mode values taken with all Connectors Removed
64
The 42LE5500 contains the Invisible Speaker system. The Full Range Speakers point downward, so there is no front viewable speaker grill or air ports.
Installed
Top View
Side View
Front View
65
This section shows the 11X17 foldout thats available in the Paper and Adobe version of the Training Manual. The Adobe version of this Training Manual allows the viewer to zoom in and out making reading of the small text easier. This Power Point shows a graphical representation of the 11 X 17 foldout page so clarity is limited.
66
The Panel contains 12 LED Blocks To force a Block to turn on, simple ground the pin providing the 13V source is present.
Gnd
To The Panel
B
C C C C C C
P204
120V n/c *1V~30V LED Drive n/c *1V~30V LED Drive n/c 120V
E
B
E B E B E B E
B
Pin 20 P201 Pin 22 P201 Pin 24 P201 Pin 23 P201 Pin 1 P201 Pin 16 P201
P205
120V n/c *1V~30V LED Drive n/c *1V~30V LED Drive n/c 120V *White 100 IRE to Black 0 IRE
E
B
E B E B E
B
C C C C
P204
C B E
Q207
Inverter
Gnd
E B E
To the Panel
These drivers ground the LED blocks. (12 Total). If the 120V is present on Pins 1 and 12 of P204 and P205 you can ground these test points to turn on a block.
Q203
T102 D206
-
P205
To the Panel
16uF/450V
EBC
P201
P201 "SMPS" To P8000 "MAIN Board" P8000 Diode Check
E B C
Q602
Label ERROR L-DIM (SIN) P-DIM 12V SCLK 12V INV-ON 12V V-SYNC Gnd 3.5V Gnd 24V PWR-ON
Run 0V 3.3V 0.38V~3.3V 11.43V 0.09V 11.43V 3.28V 11.43V 0.02V Gnd 3.5V Gnd 21.27V 3.36V
Diode Gnd 1.05V Open Open 1.06V Open 1.62V Open 1.06V Gnd 1.24V Open Open Open
SCLK Pin 20 P201 3.76V p/p S-CLK Pin 23 P201 3.25V p/p Local Dimming Off S-CLK Pin 23 P201 3.25V p/p Local Dimming On
1.45V Open Open 0.178V Open 0.178V Open 0.178V Open Gnd Open Gnd 1.10V 1.02V
P7500
IC9001 IC9003
IC9102
P8000
1 3
IC8005
T101
D202 D201
21uF/450V 21uF/450V
21uF/450V 21uF/450V
21uF/450V
D9101 SW9300
A C A C
A-C
D9102 L9301
IC9302
F101
3.15A 250V
2 L9102 Q8005 Q8002 Q8004 Q8000 Q8001 L8015 Q8003 Q8008 L9101 Q8007
D G S
2 12 3 1 3
21uF/450V
IC9000
X9000 12Mhz P9000 n/c
F103
1A 250V T501
IC502 IC503
C E B
IC8902 L8905
IC8903
IC8900
IC8901
IC8003
L601
D601
IC603 IC604
Q511
L8904 IC8202 IC8001 L8012 IC602 L8009 IC605 IC606 L8010 P9000 Gamma IC8000 IC301
Q901
16uF/450V
BD101
F102 1A
250V
F100
5A 250V
IC302 USB1
RL102
R149
(1) PDIM Pin 22 can vary according to incoming video IRE level, OSD Backlight setting and then Intelligent Sensor (room light condition) Output from the Video Processor IC900. Range 0.37V to 3.3V.
Q8308
SW1000
IC901 L8004
RL101
Micro
R149
SK101 AC In
IC8300
Component Composite
P201
SMPS TEST 1: To Force Power Supply On. Disconnect P8000 on Main board. (A) Jump pins 9, 10, 11 or 12 (3.5V) to pin 1. (Test Voltage Outputs 12V, 24V to Main and 24V to both Inverters). Remove AC power. Leave the jumper in place. SMPS TEST 2: (B) Jump pins 9, 10, 11 or 12 (3.5V) to pin 18 (INV-ON). Apply AC power, the Backlights should turn on.
Q8301
Q8304
IC8400
J2 J3
IR Receiver Intelligent Sensor
Front IR
J1
0.64V Open
P8800 "Main" To "Speakers" Pin Label SBY Run 1 SPK-R(-) 0V 12.3V 2 SPK-R(+) 0V 12.3V 3 SPK-L(-) 0V 12.3V 4 SPK-L(+) 0V 12.3V
Q?
Q8300
HP
Analog Audio
Q8700
IC8700
Q8701 Q8200
To Speakers
P8800
HDMI
A2 A1
PWR ON
D8310
P8200
STBY 3.5V
P201
Note; If there is a problem with a load on the Inverter you can Remove AC and Disconnect P205 or P204. When AC is reapplied, the Backlight LEDs should turn on for about 6 seconds and then shut off.
P8200 "MAIN Board" To J1 "IR Board" Pin Label STBY Run Diode Check SCL 3.56V 3.5V Open Intelligent Sensor 1 SDA 3.56V 3.5V Open Intelligent Sensor 2 3 Gnd Gnd Gnd Gnd 4 Key1 3.32V 3.3V 1.9V 5 Key2 3.29V 3.3V 1.9V Stand-by 6 3.5V_ST 3.56V 3.47V 1.24V
Pin Label STBY 7 Gnd Gnd 0V 8 LED_LOGO 9 IR 1.63V 10 Gnd Gnd 11 3.3V_Normal 0V 12 LED_BUZZ 0V
PWR ON
42LE5500 MAIN (FRONT SIDE) SIMICONDUCTORS IC700 (+1.26V_TU) Pin Regulator [1] 0V (Gnd) [2] 1.26V (Out) [3] 3.3V (In) SOC Reset Pin Generator [1] 3.32V (In) [2] 0V (Gnd) [3] 3.3V (Out) 5V Regulator for USB 11.79V (In) 5V (Out) 5V (Out) 10.5V 3.3V 0.8V 4.99V 0V (Gnd) D1.2V and A1.2V Regulator 0V (Gnd) 3.3V 0V (Gnd) 1.2V 3.3V n/c 4.46V 3.3V 3.3V 3.3V 1.2V Gnd 3.3V 0.8V IC8002 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] IC8003 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8004 Pin [1] [2] [3] [4] [5] [6] [7] [8] (D1.8V) Regulator IC8005 Pin [1] [2] [3] [4] [5] [6] [7] [8] (+3.3V_NORMAL) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.86V 3.36V (PWR On/Off2 Ctl) 3.36V (Out) 3.36V (Out) Power Det Gen (+12V and +3.5V) 0V (Gnd) 3.6V (In) 3.5V (Out) Power Det Gen (+24V) 0V (Gnd) 3.6V (In) 3.7V (Out) IC9100 (+1.8V_AMP) Regulator 0V (Gnd) 1.8V (Out) 3.295V (In) (+1.5V_MEMC) Regulator 0V (Gnd) 1.5V (Out) 3.3V (In) Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] IC8902 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8903 Pin [1] [2] [3] [4] [5] [6] [7] [8] (+1.26V_MEMC) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.7V 3.36V (PWR On/Off2 Ctl) 1.3V (Out) 1.3V (Out) (+3.3V_MEMC) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.8V 3.36V (PWR On/Off2 Ctl) 3.3V (Out) 3.3V (Out) P-GAMMA Chip 3.3V 0V (Gnd) 3.3V (In) 0V (Gnd) 6.8V 6.8V 15.3V 15.3V n/c 13.47V 12.75V 11.8V 10V 5.96V 4.06V 15.3V 0V 2.96V 2.33V 3.3V (In) IC9302 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q8001 IC9102 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC9300 Pin [1] [2] [3] DC to DC HVDD T-CON 0V (Gnd) 11.72V (In) 11.72V (In) 3.25V 3.2V 0V 0V 11.7V 0V (Gnd) 1.13V 0V (Gnd) 0V (Gnd) 0V (Gnd) 7.7V 7.7V (HVDD) 0V (Gnd) Reset for LG5111 3.32V (In) 0V (Gnd) 3.34V (Out) Q8201 (1.8V_L/Dimming) Regulator 0V (Gnd) 11.8V (In) 0V (Gnd) 0.8V 0.76V 3.34V (PWR On/Off2 Ctl) 1.8V (In) 1.8V (In) Pin B 0V C 3.3V E Gnd Q8306 Pin B 0V C 3.3V E Gnd Q8307 Pin B 0V C 4.18V E Gnd Q8003 PANEL_VCC Pin Control 2nd Driver B 0.679V C 0V E Gnd PANEL_VCC Pin Switch S 11.8V (In) G 1.8V (Enable) D 11.8V (Out) INV_ON Pin Driver B 0V (INV ON) En C 3.1V (Out) E Gnd IR Buffer Pin 2nd B 0.02V C 3.4V E Gnd IR Buffer 1st Q8700 Dongle Out Wireless PWR Turns on Q8701 B 0.66V C 0.14V E Gnd Wireless PWR Turns on Q8701 B 0.0V C 24V E Gnd AMP_MUTE Pin Pin 25 IC8801 B 0V C 3.336V E Gnd VGH/VDD Pin Rectifyer A 15.4V AC 22.2V C 27.4V (VGH) VGL/VCC Pin Rectifyer A (-5V VGL) AC (-1.9V) C 0V
IC1000
IC8000 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8001 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14]
5V 3.34V (In) 1.8V (Out) Gnd Gnd 0.9V 0.9V 1V 2.38V 3.36V (PWR On/Off1 Ctl) IC8007 Pin (+5V_NORMAL) [1] Regulator [2] 0V (Gnd) [3] 11.8V (In) 0V (Gnd) IC8008 0.8V Pin 0.86V [1] 3.37V (PWR On/Off2 Ctl) [2] 5V (In) [3] 5V (In) IC8800 A2.5V Regulator Pin for USB [1] n/c [2] 3.26V (In) [3] 3.26V (In) n/c IC8901 n/c Pin 2.55V (Out) [1] 0.8V [2] 0V (Gnd) [3]
Q8004
Q8700 Dongle In
Q8005
Q8800
Q8200
D9101
D9102
HDMI Det
HDMI Det
42LE5500 MAIN (BACK SIDE) SIMICONDUCTORS IC602 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8100 Pin [1] [2] [3] [4] [5] [6] [7] [8] D1.8V Regulator 0V (Gnd) 3.29V (PWR On/Off1 Ctl) 0.9V (DDR_VTT) 0.93V 1.83V 3.38V (In) 1.8V (Out) 0.91V (DDR_VTT) EEPROM Micro 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 0V (Gnd) 3.37V IC8200 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC8400 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] RS232 Routing 0V 0V 0V 0V 0V (-5.47V) n/c (5.59V) n/c (0V) n/c (3.3V) n/c (0.2V) n/c (3.3V) 3.35V 0V (-5.47V) 0V (Gnd) 3.37V RGB H/V Sync 1.9V 1.9V 4.4V 0V 0.9V n/c (4.5V) 0V (Gnd) n/c (4.5V) n/c (1.9V) n/c (1.9V) n/c (4.5V) 0.9V 0.9V 5V IC8401 Pin [1] [2] [3] [4] [5] [6] [7] [8] IC8700 Pin [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] IC9000 Pin [1] [2] [3] [4] [5] [6] [7] [8] EDID Data PC 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 0.7V 4.1V 4.5V 4.5V (In) Wireless Buffer 0V (3.3V Dongle In) 3.3V (0.3V Dongle In) n/c n/c n/c Gnd Gnd Gnd n/c 0.02V 0V 3.3V 0V (3.3V Dongle In) 3.3V 3.3V 3.3V Serial Flash T-CON 0.06V 0.67V 3.3V (In) 0V (Gnd) 0V 0.34V 3.31V (In) 3.34V (In) IC9303 Pin [1] [2] [3] [4] [5] [6] [7] [8] Q200 EEPROM for LG5111 0V (Gnd) 0V (Gnd) 0V (Gnd) 0V (Gnd) 3.37V 3.37V 3.34V 3.37V (In) Q8000 RL_ON (PWR_On) Pin 1st Driver B 0.66V C 0V E Gnd PWR_ON Pin Switch [1] 3.36V (In) [2] 0V [3] 3.3V (Out) IR Wireless Pass 2nd Driver Q8303, 4, 5 Pin B 0V C 4.2V E Gnd Q8308 Pin [B] [G] [S] [D] D8312 Pin A1 C A2 D8306, 7, 9 Q8205 Pin B 0.6V C 0V E Gnd Q8300, 2 Pin B 4.2V C 0V E Gnd IR Wireless Pass 1st Driver HDMI 3 Det
Q8002
(1.8V_HDMI) Pin Switch S 1.83V (Out) G 3.35V (PWR On/Off2 Ctl) D 1.83V (In) Tuner SIF Pin (Sound) Buffer B 0.16V C Gnd E 0.83V Tuner Video Pin (Analog) Buffer B 2.05V C 2.75V E Gnd FLASH_WP Pin for IC901 B 0V (Flash_WP) C 3.36V E Gnd
CEC Remote HDMI CEC 2.72V 2.73V 3.27V 3.37V 3.5V Pull Up HDMI CEC 0V 3.26V 3.2V
Q701
Q702
HDMI 2 Det
Q901