Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
6 7 8 9
The Computer Aided Engineering Drawing outcomes leading to the achievement of the objectives are summarized in the following table. CO CEO 1 2 3 a X b X X X X Page 1 c d e f g X X h
Evaluation Plan:
1. 2. 3. 4. Seminar & Presentations Assignments Internal Assessment Test Semester end Exam
Text Books:
1. Engineering Drawing - N.D. Bhatt & V.M. Panchal, 48th edition, 2005-Charotar Publishing House, Gujarat. 2. A Primer on Computer Aided Engineering Drawing-2006, Published by VTU, Belgaum.
Reference Books:
1. Computer Aided Engineering Drawing - S. Trymbaka Murthy, - I.K. International Publishing House Pvt. Ltd., New Delhi, 3rd revised edition- 2006. 2. Engineering Graphics - K.R. Gopalakrishna, 32nd edition, 2005- Subash Publishers Bangalore. 3. Fundamentals of Engineering Drawing with an Introduction to Interactive Computer Graphics for Design and Production- Luzadder Warren J., Duff John M., Eastern Economy Edition, 2005- Prentice-Hall of India Pvt. Ltd., New Delhi. 4. Computer Aided Engineering drawing- Prof. M. H. Annaiah, New Age International Publisher, New Delhi. 2009.
Conducting classes
Classes will be conducted in two slots/ week of 3 hours each (Instruction 1 hr. +Sketching & Practice 2 hr.)
Scheme of Examination
1. Chapter 1 is only for practice and Internal Assessment and not for examination. 2. Separate Question paper must be set for each batch of students, jointly by the Internal & External examiners. 3. A maximum of THREE questions must be set as per the following pattern (No mixing of questions from different Chapters). Q. No. 1. 2. 3. From Chapters Chapter 2 or Chapter 3 Chapter 4 Chapter 5 or Chapter 6 Total Marks Allotted 30 40 30 100
Scheme of Evaluation
Q. No. Solutions & Sketching on Computer display Total Marks graph book & printout 1. 2. 3. Total 10 Marks 15 Marks 15 Marks 40 Marks 20 Marks 25 Marks 15 Marks 60 Marks 30 40 30 100
Students have to submit the computer printouts and the sketches drawn on the graph sheets at the end of the examination. Both Internal & External examiners have to jointly evaluate the solutions (sketches) and computer display & printouts of each student for 100 marks (40 marks for solutions & sketches + 60 marks for computer display and printouts) and submit the marks list along with the solution (sketches) on graph sheets & computer printouts in separate covers. Each batch must consist of a minimum of 10 students and a maximum of 12 students.
Page 3
Unit 1 2 3 4 5 6
Title of the Unit Introduction to Computer Aided Sketching Orthographic Projections Orthographic Projections of Plane Surfaces (First Angle Projection Only) Projections of Solids (First angle Projection only) Sections And Development of Lateral Surfaces of Solids Isometric Projection (Using Isometric Scale Only)
Computer Aided Engineering Drawing 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. 63. Department of Mechanical Engineering Projections of triangular, square, rectangular, rhombus, pentagonal and hexagonal pyramids in different positions. Projections of cylinders in different positions. Projections of cones in different positions. Introduction, Section planes, Sections, Section views, Sectional views, Apparent shapes and True Page 5
True and apparent lengths, True and apparent inclinations to reference planes (No application problems). Introduction Definitionsprojections of plane surfaces Problems on Triangle, square planes in different positions by change of position method only (No problems on punched plates and composite plates). Problems on rectangle, rhombus planes in different positions by change of position method only (No problems on punched plates and composite plates). Problems on pentagon, hexagon and circle planes in different positions by change of position method only (No problems on punched plates and composite plates). Introduction Definitions
Projections of right regular tetrahedron, Hexahedron (cube), (No problems on octahedrons and combination solid).
Projections of triangular, square, rectangular, rhombus, pentagonal and hexagonal prisms in different positions.
Computer Aided Engineering Drawing 64. 65. 66. 67. 68. 69. 70. 71. 72. 73. 74. 75. 76. 77. 78. 79. 80. 81. 82.
shapes of Sections of right regular prisms, pyramids, cylinders and cones resting with base on HP. (No problems on sections of solids) Development of lateral surfaces of above solids, their frustums and truncations. (No problems on lateral surfaces of trays, tetrahedrons, spheres and transition pieces). Introduction. Isometric scale, Isometric projection of simple plane figures.
Isometric projection of tetrahedron, hexahedron(cube), right regular prisms, Pyramids, cylinders, cones, spheres, cut spheres and combination of solids. (Maximum of three solids).
Course Objective (4): Learn to take data and transform it into graphic drawings.
Course Outcomes: Students ability to produce engineered drawings will improve. Students ability to convert sketches into engineered drawings will increase. Department of Mechanical Engineering Page 6
Computer Aided Engineering Drawing Assignments: that demonstrate accomplishment of this outcome. 1. Students are required to go on a field project, take the dimensions of a predetermined project sketch them on engineering paper and transfer the data to an electronic drawing. 2. Students are required to take sketches and technical drawings from a technical drawing and convert them into cad drawings.
Course Objective (7): Prepare the student for future Engineering positions:
Course Outcomes: Students will develop good communication skills and team work Assignments: that demonstrate accomplishment of this outcome. 1. In the professional project, students are broken down into teams to work on a real life project and deal with real life clients. Students must go through the five stages of the design process to solve a real life project, culminating in a presentation to the client, with the client judging the students on their performance.
Page 7