Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
SECTION
BCS
CONTENTS
BASIC INSPECTION ................................ .... 3
INSPECTION AND ADJUSTMENT ................ ..... 3
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) ......................................... ...... 3 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description ................. ...... 3 ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair Requirement .................................................................... ...... 3 CONFIGURATION (BCM) ..................................... ...... 3 CONFIGURATION (BCM) : Description .............. ...... 3 CONFIGURATION (BCM) : Special Repair Requirement ............................................................ ...... 4 CONFIGURATION (BCM) : Configuration list ..... ...... 5 COMMON ITEM ..................................................... ....16 COMMON ITEM : CONSULT-III Function (BCM COMMON ITEM) ................................................. ....16 DOOR LOCK .......................................................... ....17 DOOR LOCK : CONSULT-III Function (BCM DOOR LOCK) ...................................................... ....17 REAR WINDOW DEFOGGER ............................... ....18 REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER) ................. ....18 BUZZER ................................................................. ....18 BUZZER : CONSULT-III Function (BCM - BUZZER) ...................................................................... ....19 INT LAMP ............................................................... ....19 INT LAMP : CONSULT-III Function (BCM - INT LAMP) .................................................................. ....19 HEADLAMP ........................................................... ....21 HEADLAMP : CONSULT-III Function (BCM HEAD LAMP) ....................................................... ....21 WIPER .................................................................... ....23 WIPER : CONSULT-III Function (BCM - WIPER)....23 FLASHER ............................................................... ....24 FLASHER : CONSULT-III Function (BCM FLASHER) ........................................................... ....24 INTELLIGENT KEY ................................................ ....25 INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) ................................ ....25 COMB SW .............................................................. ....28 COMB SW : CONSULT-III Function (BCM COMB SW) .......................................................... ....28 BCM ....................................................................... ....28 BCM : CONSULT-III Function (BCM - BCM) ....... ....28 IMMU ...................................................................... ....29 IMMU : CONSULT-III Function (BCM - IMMU) .... ....29
BCS
BCS-1
BATTERY SAVER ................................................. ... 29 BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER) ........................................... ... 29 TRUNK ................................................................... ... 30 TRUNK : CONSULT-III Function (BCM - TRUNK)... 30 THEFT ALM ........................................................... ... 31 THEFT ALM : CONSULT-III Function (BCM THEFT) ................................................................ ... 31 SIGNAL BUFFER ................................................... ... 32 SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER) ............................................. ... 32
PRECAUTION ............................................ 77
PRECAUTIONS .............................................. ... 77
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" .............................................................. ... 77
BCS-2
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM)
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description
INFOID:0000000003809644
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT-III configuration before replacement. NOTE: If READ CONFIGURATION can not be used, use the WRITE CONFIGURATION - Manual selection after replacing BCM.
D
AFTER REPLACEMENT
CAUTION: When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III. - Complete the procedure of WRITE CONFIGURATION in order. - If you set incorrect WRITE CONFIGURATION, incidents might occur. - Configuration is different for each vehicle model. Confirm configuration of each vehicle model. When replacing BCM, perform the system initialization (NATS).
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair Requirement
INFOID:0000000003809645
2.REPLACE BCM
Replace BCM. Refer to BCS-78, "Exploded View". >> GO TO 3.
L
BCS
CONFIGURATION (BCM)
CONFIGURATION (BCM) : Description
INFOID:0000000003809646
Vehicle specification needs to be written with CONSULT-III because it is not written after replacing BCM.
BCS-3
CAUTION: When replacing BCM, you must perform WRITE CONFIGURATION with CONSULT-III. Complete the procedure of WRITE CONFIGURATION in order. If you set incorrect WRITE CONFIGURATION, incidents might occur. Configuration is different for each vehicle model. Confirm configuration of each vehicle model. Never perform WRITE CONFIGURATION except for new BCM.
INFOID:0000000003809647
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally. >> WORK END
BCS-4
INFOID:0000000003809648
A
NOTE WITH: With BOSE audio system WITHOUT: Without BOSE audio system
NOTE
BCS
BCS-5
FUNCTION DIAGNOSIS
BODY CONTROL SYSTEM
System Description
OUTLINE
BCM (Body Control Module) controls the various electrical components. It inputs the information required to the control from CAN communication and the signal received from each switch and sensor. BCM has combination switch reading function for reading the operation status of combination switches (light, turn signal, wiper and washer) in addition to a function for controlling the operation of various electrical components. It also has the signal transmission function as the passed point of signal and the power saving control function that reduces the power consumption with the ignition switch OFF. BCM is equipped with the diagnosis function that performs the diagnosis with CONSULT-III and various settings.
INFOID:0000000003809584
BCS-6
B
DLK-14, "INTELLIGENT KEY SYSTEM : System Diagram"
INFOID:0000000003809585
I
JPMIA1040ZZ
1. A.
BCS
BCS-7
JPMIA0734GB
System Description
OUTLINE
INFOID:0000000003809587
BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch. BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a maximum of 20 switch status.
JPMIA0735GB
OUTPUT 2 FR WASHER
BCS-8
F
JPMIA0067GB
NOTE: BCM reads the status of the combination switch at 60 ms interval when BCM is controlled at low power consumption mode. BCM operates as follows and judges the status of the combination switch. INPUT 1 - 5 outputs the voltage waveforms of 5 systems simultaneously. It operates the transistor on OUTPUT side in the following order: OUTPUT 5 4 3 2 1. The voltage waveform of INPUT corresponding to the formed circuit changes according to the operation of the transistor on OUTPUT side if any (1 or more) switches are ON. It reads this change of the voltage as the status signal of the combination switch.
BCS
P
JPMIA0068GB
Operation Example In the following operation example, the combination of the status signals of the combination switch is replaced as follows: INPUT 1 - 5 to 1 - 5 and OUTPUT 1 - 5 to A - E.
Example 1: When a switch (TURN RH switch) is turned ON
BCS-9
JPMIA0736GB
BCM detects the combination switch status signal 1E when the signal of OUTPUT 5 is input to INPUT 1. BCM judges that the TURN RH switch is ON when the signal 1E is detected.
Example 2: When some switches (turn RH switch, front wiper LO switch) are turned ON
The circuits between INPUT 1 and OUTPUT 5 and between INPUT 1 and OUTPUT 3 are formed when the TURN RH switch and FR WIPER LOW switch are turned ON.
JPMIA0737GB
BCM detects the combination switch status signal 1CE when the signals of OUTPUT 3 and OUTPUT 5 are input to INPUT 1. BCM judges that the TURN RH switch and FR WIPER LOW switch are ON when the signal 1CE is detected.
BCS-10
JPMIA1041ZZ
1. A.
2.
BCM
BCS
BCS-11
JPMIA1045GB
System Description
OUTLINE
INFOID:0000000003809590
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Combination meter (CAN) IPDM E/R (CAN) Driver seat control unit (CAN) AV control unit (CAN)
TCM (CAN)
BCS-12
JPMIA1046GB
System Description
OUTLINE
INFOID:0000000003809592
BCM incorporates a power saving control function that reduces the power consumption according to the vehicle status. BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep request to each unit (IPDM E/R, combination meter, driver seat control unit and automatic back door control unit) that operates with the ignition switch OFF.
Normal mode (wake-up)
- CAN communication is normally performed with other units - Each control with BCM is operating properly
CAN communication sleep mode (CAN sleep)
BCS-13
CAN sleep condition Receiving the sleep-ready signal (ready) from all units Ignition switch: OFF Vehicle security system: Not operation Warning chime: Not operation Intelligent Key system buzzer: Not operation Trunk room lamp switch status: No change Stop lamp switch: OFF Key slot (card switch) status: No change Turn signal indicator lamp: Not operation Exterior lamp: OFF Door lock status: No change CONSULT-III communication status: Not communication Meter display signal: Non-transmission Door switch status: No change Rear window defogger: OFF
Interior room lamp battery saver: Time out Push-button ignition switch illumination: OFF Nissan Vehicle Immobilizer System (NVIS) - NATS: Not operation Remote keyless entry receiver communication status: No communication ACC indicator lamp: Not operation ON indicator lamp: Not operation
Wake-up operation
BCM changes from the low power consumption mode to the CAN communication sleep mode when the any of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated. BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the normal mode. Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the combination meter transmits the wake up signal to BCM via CAN communication to report the CAN communication start.
Wake-up condition
CAN wake-up condition Receiving the sleep-ready signal (Not-ready) from any units Key slot (key switch): OFF ON, ON OFF Push-button ignition switch (push switch): OFF ON Hazard switch: OFF ON PASSING switch: OFF ON, ON OFF TAIL LAMP switch: OFF ON Driver door switch: OFF ON, ON OFF Passenger door switch: OFF ON, ON OFF Rear RH door switch: OFF ON, ON OFF Rear LH door switch: OFF ON, ON OFF Trunk room lamp switch: OFF ON, ON OFF Driver door request switch: OFF ON Passenger door request switch: OFF ON Trunk lid request switch: OFF ON Stop lamp switch: ON
Trunk lid opener switch: OFF ON Remote keyless entry receiver: Receiving Door lock and unlock switch: NEUTRAL LOCK, NEUTRAL UNLOCK Front door lock assembly driver side (unlock sensor): OFF ON, ON OFF
BCS-14
INFOID:0000000003809593
JPMIA1042ZZ
1. 4. A.
2. B.
3. C.
BCS
BCS-15
SYSTEM APPLICATION
BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selection items.
: Applicable item
System Door lock Rear window defogger Warning chime Interior room lamp timer Exterior lamp Wiper and washer Turn signal and hazard warning lamps Intelligent Key system Engine start system Combination switch Body control system NVIS - NATS Interior room lamp battery saver Trunk lid opener system Vehicle security system Signal buffer system NOTE: *: This item is displayed, but is not used.
Sub system selection item DOOR LOCK REAR DEFOGGER BUZZER INT LAMP HEAD LAMP WIPER FLASHER AIR CONDITONER* INTELLIGENT KEY COMB SW BCM IMMU BATTERY SAVER TRUNK THEFT ALM RETAINED PWR* SIGNAL BUFFER TPMS (AIR PRESSURE MONITOR)*
BCS-16
IGN Counter IGN counter indicates the number of times that ignition switch is turned ON after DTC is detected. L The number is 0 when a malfunction is detected now. The number increases like 1 2 3...38 39 after returning to the normal condition whenever ignition switch OFF ON. BCS The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode WORK SUPPORT DATA MONITOR ACTIVE TEST Function Description Changes the setting for each system function. The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM.
INFOID:0000000003897052
WORK SUPPORT
BCS-17
DATA MONITOR
Monitor Item REQ SW-DR REQ SW-AS REQ SW-BD/TR DOOR SW-DR DOOR SW-AS DOOR SW-RR DOOR SW-RL DOOR SW-BK CDL LOCK SW CDL UNLOCK SW KEY CYL LK-SW KEY CYL UN-SW Contents Indicates [ON/OFF] condition of door request switch (driver side). Indicates [ON/OFF] condition of door request switch (passenger side). Indicates [ON/OFF] condition of trunk lid opener request switch. Indicates [ON/OFF] condition of front door switch (driver side). Indicates [ON/OFF] condition of front door switch (passenger side). Indicates [ON/OFF] condition of rear door switch RH. Indicates [ON/OFF] condition of rear door switch LH. NOTE: This item is displayed, but cannot be monitored. Indicates [ON/OFF] condition of lock signal from door lock unlock switch. Indicates [ON/OFF] condition of unlock signal from door lock unlock switch. Indicates [ON/OFF] condition of lock signal from door key cylinder. Indicates [ON/OFF] condition of unlock signal from door key cylinder.
ACTIVE TEST
Test item Description This test is able to check door lock/unlock operation. The all door lock actuators are locked when ALL LCK on CONSULT-III screen is touched. The all door lock actuators are unlocked when ALL UNLK on CONSULT-III screen is touched. The door lock actuator (driver side) is unlocked when DR UNLK on CONSULT-III screen is touched. The door lock actuator (passenger side) is unlocked when AS UNLK on CONSULT- III screen is touched. The door lock actuator (rear LH and RH) is unlocked when OTR ULK on CONSULT-III screen is touched.
DOOR LOCK
Data monitor
Monitor Item REAR DEF SW PUSH SW Description Without AV control unit: Displays Press (ON)/other (OFF) status determined with the rear window defogger switch With AV control unit: This is displayed even when it is not equipped Indicates [ON/OFF] condition of push switch
ACTIVE TEST
Test Item REAR DEFOGGER Description This test is able to check rear window defogger operation. Rear window defogger operates when ON on CONSULT-III screen is touched
BUZZER
BCS-18
INFOID:0000000003897064
DATA MONITOR
Display item [Unit] PUSH SW [On/Off] UNLK SEN-DR [On/Off] VEH SPEED 1 [km/h] KEY SW-SLOT [On/Off] TAIL LAMP SW [On/Off] FR FOG SW [On/Off] DOOR SW-DR [On/Off] Description Status of push button ignition switch judged by BCM. Status of unlock sensor judged by BCM. Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN communication line. Status of key slot judged by BCM.
G
Status of each switch judged by BCM using the combination switch readout function. Status of front fog lamp switch judged by BCM. Status of driver side door switch judged by BCM.
ACTIVE TEST
Display item [Unit] IGN KEY WARN ALM LIGHT WARN ALM RUN FLAT/T WARN BUZZER Description The key warning chime operation can be checked by operating the relevant function (On/Off). The light warning chime operation can be checked by operating the relevant function (On/Off). This item is displayed, but not function.
INT LAMP
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
WORK SUPPORT
INFOID:0000000003897059
BCS
JPLIA0093GB
BCS-19
DATA MONITOR
Monitor item [Unit] REQ SW-DR [On/Off] REQ SW-AS [On/Off] PUSH SW [On/Off] KEY SW-SLOT [On/Off] DOOR SW-DR [On/Off] DOOR SW-AS [On/Off] DOOR SW-RR [On/Off] DOOR SW- RL [On/Off] DOOR SW-BK [On/Off] CDL LOCK SW [On/Off] CDL UNLOCK SW [On/Off] KEY CYL LK-SW [On/Off] KEY CYL UN-SW [On/Off] Description The switch status input from request switch (driver side) The switch status input from front request switch (passenger side) The switch status input from push-button ignition switch Key switch status input from key slot The switch status input from front door switch (driver side) The switch status input from front door switch (passenger side) The switch status input from rear door switch RH The switch status input from rear door switch LH NOTE: The item is indicated, but not monitored. Lock switch status received from door lock/unlock switch Unlock switch status received from door lock/unlock switch NOTE: The item is indicated, but not monitored. NOTE: The item is indicated, but not monitored.
BCS-20
ACTIVE TEST
Test item INT LAMP Operation On Off STEP LAMP TEST On Off On Off Description Outputs the interior room lamp control signal to turn map lamp and personal lamp ON (Map lamp switch is in DOOR position). Stops the interior room lamp control signal to turn map lamp and personal lamp OFF. Outputs the step lamp control signal to turn step lamp ON. Stops the step lamp control signal to turn step lamp OFF. Outputs the trunk room lamp control signal to turn trunk room lamp ON. Stops the trunk room lamp control signal to turn trunk room lamp OFF.
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
WORK SUPPORT
Service item BATTERY SAVER SET Setting item On* Off MODE 1* MODE 2 MODE 3 ILL DELAY SET MODE 4 MODE 5 MODE 6 MODE 7 MODE 8 MODE 1* CUSTOM A/LIGHT SETTING MODE 2 MODE 3 MODE 4 *: Factory setting Setting With the exterior lamp battery saver function Without the exterior lamp battery saver function 45 sec. Without the function 30 sec. 60 sec. 90 sec. 120 sec. 150 sec. 180 sec. Normal More sensitive setting than normal setting (Turns ON earlier than normal operation.) More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.) Less sensitive setting than normal setting (Turns ON later than normal operation.) Sets delay timer function timer operation time. (All doors closed)
INFOID:0000000003897061
BCS
DATA MONITOR
P
Monitor item [Unit] PUSH SW [On/Off] ENGINE STATE [Stop/Stall/Crank/Run] Description The switch status input from push-button ignition switch The engine status received from ECM with CAN communication
BCS-21
Each switch status that BCM detects from the combination switch reading function
ACTIVE TEST
Test item TAIL LAMP Operation On Off Hi HEAD LAMP Low Off FR FOG LAMP On Off Description Transmits the position light request signal to IPDM E/R with CAN communication to turn the tail lamp ON. Stops the position light request signal transmission. Transmits the high beam request signal with CAN communication to turn the headlamp (HI). Transmits the low beam request signal with CAN communication to turn the headlamp (LO). Stops the high & low beam request signal transmission. Transmits the front fog lights request signal to IPDM E/R with CAN communication to turn the front fog lamp ON. Stops the front fog lights request signal transmission.
BCS-22
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
WORK SUPPORT
G
Service item WIPER SPEED SETTING *:Factory setting NOTE: When performed RESET SETTING VALUE on Work Support (BCM - BCM), set WIPER SPEED SETTING on Work Support (BCM -WIPER) to On. Setting item On* Off Description With vehicle speed (Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position) Without vehicle speed (Front wiper intermittent time linked with the wiper intermittent dial position)
INFOID:0000000003897063
DATA MONITOR
Monitor Item [Unit] PUSH SW [Off/On] VEH SPEED 1 [km/h] FR WIPER HI [Off/On] FR WIPER LOW [Off/On] FR WASHER SW [Off/On] FR WIPER INT [Off/On] FR WIPER STOP [Off/On] INT VOLUME [1 7] H/L WASH SW [Off/On] Displays the status of the front wiper stop position signal received from IPDM E/R with CAN communication. Status of each switch judged by BCM using the combination switch reading function Status of the switch input from headlamp washer switch
K
Description The switch status input from push-button ignition switch. Displays the value of the vehicle speed signal received from combination meter with CAN communication.
BCS
N
Status of each switch judged by BCM using the combination switch reading function
ACTIVE TEST
BCS-23
FRONT WIPER
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
WORK SUPPORT
Service item Setting item Lock Only* HAZARD ANSWER BACK Unlk Only Lock/Unlk Off *: Factory setting With locking only With unlocking only With locking/unlocking Without the function Sets the hazard warning lamp answer back function when the door is lock/unlock with the request switch or the key fob. Setting
INFOID:0000000003897062
DATA MONITOR
Monitor item [Unit] REQ SW-DR [On/Off] REQ SW-AS [On/Off] PUSH SW [On/Off] TURN SIGNAL R [On/Off] TURN SIGNAL L [On/Off] HAZARD SW [On/Off] RKE-LOCK [On/Off] RKE-UNLOCK [On/Off] RKE-PANIC [On/Off] Description The switch status input from the request switch (driver side) The switch status input from the request switch (passenger side) The switch status input from the push-button ignition switch
Each switch status that BCM detects from the combination switch reading function
The switch status input from the hazard switch Lock signal status received from the remote keyless entry receiver Unlock signal status received from the remote keyless entry receiver Panic alarm signal status received from the remote keyless entry receiver
ACTIVE TEST
Test item Operation RH FLASHER LH Off Description Outputs the voltage to blink the right side turn signal lamps. Outputs the voltage to blink the left side turn signal lamps. Stops the voltage to turn the turn signal lamps OFF.
BCS-24
INTELLIGENT KEY
A
INFOID:0000000003897053
WORK SUPPORT
Monitor item REMO CONT ID CONFIR Description It can be checked whether Intelligent Key ID code is registered or not in this mode. Auto door lock time can be changed in this mode. MODE 1: 1 minute MODE 2: 5 minutes MODE 3: 30 seconds MODE 4: 2 minutes Door lock/unlock function by door request switch (driver side and passenger side) mode can be changed to operate (WITH) or not operate (WITHOUT) in this mode. Engine start function mode can be changed to operate (WITH) or not operate (WITHOUT) in this mode. Buzzer reminder function mode by trunk lid opener request switch can be changed to operate (WITH) or not operate (WITHOUT) in this mode. NOTE: This item is displayed, but cannot be used. NOTE: This item is displayed, but cannot be used. Trunk button pressing on Intelligent Key button can be selected as per the following in this mode. MODE 1: Press and hold MODE 2: Press twice MODE 3: Press and hold, or press twice Intelligent Key low battery warning mode can be changed to operate (WITH) or not operate (WITHOUT) in this mode. Key reminder function mode can be changed to operate (WITH) or not operate (WITHOUT) in this mode. Hazard reminder function mode can be selected from the following in this mode. LOCK ONLY: Door lock operation only UNLOCK ONLY: Door unlock operation only LOCK/UNLOCK: Lock/unlock operation OFF: Non-operational Buzzer reminder function (lock operation) mode by door request switch (driver side and passenger side) can be selected from the following is this mode. Horn chirp: Sound horn Buzzer: Sound Intelligent Key warning buzzer OFF: Non-operational Buzzer reminder function (unlock operation) mode by door request switch can be changed to operate (ON) or not operate (OFF) in this mode. Starter motor can operate during the times below. 70 msec 100 msec 200 msec
LOCK/UNLOCK BY I-KEY ENGINE START BY I-KEY TRUNK/GLASS HATCH OPEN PANIC ALARM SET PW DOWN SET
BCS
BCS-25
SELF-DIAG RESULT
Refer to BCS-74, "DTC Index".
DATA MONITOR
Monitor Item REQ SW -DR REQ SW -AS REQ SW -BD/TR PUSH SW IGN RLY2 -F/B CLUCH SW BRAKE SW 1 DETE/CANCL SW SFT PN/N SW S/L -LOCK S/L -UNLOCK S/L RELAY -F/B UNLK SEN -DR PUSH SW -IPDM IGN RLY1 -F/B DETE SW -IPDM SFT PN -IPDM SFT P -MET SFT N -MET ENGINE STATE S/L LOCK-IPDM S/L UNLK-IPDM S/L RELAY-REQ VEH SPEED 1 VEH SPEED 2 DOOR STAT-DR DOOR STAT-AS ID OK FLAG PRMT ENG STRT PRMT RKE STRT KEY SW -SLOT TRNK/HAT MNTR RKE-LOCK RKE-UNLOCK RKE-TR/BD Condition Indicates [ON/OFF] condition of door request switch (driver side). Indicates [ON/OFF] condition of door request switch (passenger side). Indicates [ON/OFF] condition of trunk lid opener request switch. Indicates [ON/OFF] condition of push-button ignition switch. Indicates [ON/OFF] condition of ignition relay 2. NOTE: This item is displayed, but cannot be monitored. Indicates [ON/OFF] condition of brake switch. Indicates [ON/OFF] condition of the P position. Indicates [ON/OFF] condition of the P or N position. Indicates [ON/OFF] condition of steering lock unit (LOCK). Indicates [ON/OFF] condition of steering lock unit (UNLOCK). Indicates [ON/OFF] condition of steering lock relay. Indicates [ON/OFF] condition of driver door UNLOCK status. Indicates [ON/OFF] condition of push-button ignition switch. Indicates [ON/OFF] condition of ignition relay 1. Indicates [ON/OFF] condition of the P position. Indicates [ON/OFF] condition of the P or N position. Indicates [ON/OFF] condition of the P position. Indicates [ON/OFF] condition of the N position. Indicates [STOP/STALL/CRANK/RUN] condition of engine states. Indicates [ON/OFF] condition of steering lock unit (LOCK). Indicates [ON/OFF] condition of steering lock unit (UNLOCK). Indicates [ON/OFF] condition of steering lock relay. Displays the vehicle speed signal received from combination meter by numerical value [Km/h]. Displays the vehicle speed signal received from ABS, VDC or CVT by numerical value [Km/h]. Indicates [LOCK/READY/UNLK] condition of driver side door status. Indicates [LOCK/READY/UNLK] condition of passenger side door status. Indicates [SET/RESET] condition of key ID. Indicates [SET/RESET] condition of engine start possibility. NOTE: This item is displayed, but cannot be monitored. Indicates [ON/OFF] condition of key slot. Indicates [ON/OFF] condition of trunk lid. Indicates [ON/OFF] condition of LOCK signal from Intelligent Key. Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key. Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
BCS-26
ACTIVE TEST
Test item BATTERY SAVER PW REMOTO DOWN SET OUTSIDE BUZZER Description This test is able to check interior room lamp operation. The interior room lamp will be activated when ON on CONSULT-III screen is touched. NOTE: This item is displayed, but cannot be used. This test is able to check Intelligent Key warning buzzer operation. The Intelligent Key warning buzzer will be activated when ON on CONSULT-III screen is touched. This test is able to check warning chime in combination meter operation. Take away warning chime sounds when TAKE OUT on CONSULT-III screen is touched. Key warning chime sounds when KEY on CONSULT-III screen is touched. P position warning chime sounds when KNOB on CONSULT-III screen is touched. This test is able to check warning lamp operation. KEY Warning lamp illuminates when RED ON on CONSULT-III screen is touched. KEY Warning lamp blinks when RED IND on CONSULT-III screen is touched. This test is able to check interior room lamp operation. The interior room lamp will be activated when ON on CONSULT-III screen is touched. This test is able to check meter display information Engine start information displays when BP N on CONSULT-III screen is touched. Engine start information displays when BP I on CONSULT-III screen is touched. Key ID warning displays when ID NG on CONSULT-III screen is touched. Steering lock information displays when ROTAT on CONSULT-III screen is touched. P position warning displays when SFT P on CONSULT-III screen is touched. Intelligent Key insert information displays when INSRT on CONSULT-III screen is touched. Intelligent Key low battery warning displays when BATT on CONSULT-III screen is touched. Take away warning displays when OUTKEY on CONSULT-III screen is touched. OFF position warning displays when LK WN on CONSULT-III screen is touched. This test is able to check trunk lid opener actuator open operation. This actuator opens when OPEN on CONSULT-III screen is touched. This test is able to check security hazard lamp operation. The hazard lamps will be activated when RH or LHon CONSULT-III screen is touched. This test is able to check horn operation. The horn will be activated when ON on CONSULT-III screen is touched. This test is able to check control device power supply Control device power is supplied when ON on CONSULT-III screen is touched. This test is able to check push-ignition switch illumination operation. Push-ignition switch illumination illuminates when ON on CONSULT-III screen is touched. This test is able to check LOCK indicator in push-ignition switch operation. LOCK indicator in push-ignition switch illuminates when ON on CONSULT-III screen is touched. This test is able to check ACC indicator in push-ignition switch operation. ACC indicator in push-ignition switch illuminates when ON on CONSULT-III screen is touched. This test is able to check ON indicator in push-ignition switch operation. ON indicator in push-ignition switch illuminates when ON on CONSULT-III screen is touched.
INSIDE BUZZER
INDICATOR
INT LAMP
LCD
TRUNK/GLASS HATCH FLASHER HORN P RANGE ENGINE SW ILLUMI LOCK INDICATOR ACC INDICATOR IGNITION ON IND
BCS
BCS-27
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
DATA MONITOR
Monitor item [UNIT] FR WIPER HI [Off/On] FR WIPER LOW [Off/On] FR WASHER SW [Off/On] FR WIPER INT [Off/On] FR WIPER STOP [Off/On] INT VOLUME [1 - 7] TURN SIGNAL R [Off/On] TURN SIGNAL L [Off/On] TAIL LAMP SW [Off/On] HI BEAM SW [Off/On] HEAD LAMP SW 1 [Off/On] HEAD LAMP SW 2 [Off/On] PASSING SW [Off/On] AUTO LIGHT SW [Off/On] FR FOG SW [Off/On] RR FOG SW [Off/On] Description Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication. Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading function. Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch reading function. Displays the status of the RR FOG switch in combination switch judged by BCM with the combination switch reading function.
INFOID:0000000003809604
BCM
BCM : CONSULT-III Function (BCM - BCM)
WORK SUPPORT
Item RESET SETTING VALUE NOTE: Description Return a value set with Work Support of each system to a default value in factory shipment.
INFOID:0000000003809605
BCS-28
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode DATA MONITOR ACTIVE TEST Function Description The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM.
INFOID:0000000003897057
DATA MONITOR
Monitor item CONFRM ID ALL CONFIRM ID4 CONFIRM ID3 CONFIRM ID2 CONFIRM ID1 TP 4 TP 3 TP 2 TP 1 PUSH SW KEY SW -SLOT Indicates [ON/OFF] condition of push-button ignition switch. Indicates [ON/OFF] condition of key slot. Indicates [YET] at all time. Switches to [DONE] when a registered Intelligent Key is inserted into the key slot. Content
H
Indicates the number of ID which has been registered.
ACTIVE TEST
Test item THEFT IND Description This test is able to check security indicator lamp operation. The lamp will be turned on when ON on CONSULT-III screen touched.
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
WORK SUPPORT
Service item BATTERY SAVER SET Setting item On* Off On* Off MODE 1* MODE 2 Setting With the exterior lamp battery saver function Without the exterior lamp battery saver function With the interior room lamp battery saver function Without the interior room lamp battery saver function 30 min. 60 min. Sets the interior room lamp battery saver timer operating time.
INFOID:0000000003897060
BCS
DATA MONITOR
BCS-29
ACTIVE TEST
Test item BATTERY SAVER *: Each lamp switch is in ON position. Operation Off On Description Cuts the interior room lamp power supply to turn interior room lamp OFF. Outputs the interior room lamp power supply to turn interior room lamp ON.*
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode DATA MONITOR ACTIVE TEST Function Description The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM.
INFOID:0000000003897054
DATA MONITOR
BCS-30
ACTIVE TEST
Test item TRUNK/GLASS HATCH Description This test is able to check trunk lid opener actuator open operation.
THEFT ALM
THEFT ALM : CONSULT-III Function (BCM - THEFT)
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
Diagnosis mode WORK SUPPORT DATA MONITOR ACTIVE TEST Function Description Changes the setting for each system function. The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM.
INFOID:0000000003897056
DATA MONITOR
Monitored Item REQ SW -DR REQ SW -AS REQ SW -RR REQ SW -RL REQ SW -BD/TR PUSH SW UNLK SEN -DR KEY SW -SLOT DOOR SW-DR DOOR SW-AS DOOR SW-RR DOOR SW-RL DOOR SW-BK Description Indicates [ON/OFF] condition of door request switch (driver side). Indicates [ON/OFF] condition of door request switch (passenger side). NOTE: This is displayed even when it is not equipped. NOTE: This is displayed even when it is not equipped. Indicates [ON/OFF] condition of trunk lid opener request switch. Indicates [ON/OFF] condition of push-button ignition switch Indicates [ON/OFF] condition of driver door UNLOCK status. Indicates [ON/OFF] condition of key slot. Indicates [ON/OFF] condition of front door switch (driver side). Indicates [ON/OFF] condition of front door switch (passenger side). Indicates [ON/OFF] condition of rear door switch RH. Indicates [ON/OFF] condition of rear door switch LH. NOTE: This is displayed even when it is not equipped.
BCS
BCS-31
WORK SUPPORT
Test Item SECURITY ALARM SET THEFT ALM TRG Description This mode is able to confirm and change security alarm ON-OFF setting. The switch which triggered vehicle security alarm is recorded. This mode is able to confirm and erase the record of vehicle security alarm. The trigger data can be erased by touching CLEAR on CONSULT-III screen.
ACTIVE TEST
Test Item THEFT IND HEADLAMP(HI) FLASHER Description This test is able to check security indicator lamp operation. The lamp will be turned on when ON on CONSULT-III screen is touched. This test is able to check vehicle security lamp operation. The headlamps will be activated for 0.5 seconds after ON on CONSULT-III screen is touched. This test is able to check vehicle security hazard lamp operation. The hazard lamps will be activated after ON on CONSULT-III screen is touched.
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT-III Function (BCM - SIGNAL BUFFER)
DATA MONITOR
Monitor item [UNIT] PUSH SW [Off/On] Description Displays the status of the push-button ignition switch (push switch) judged by BCM.
INFOID:0000000003809611
ACTIVE TEST
Test item Operation Off OIL PRESSURE SW On OFF BCM transmits the oil pressure switch signal to the combination meter via CAN communication, which illuminates the oil pressure warning lamp in the combination meter. Description
BCS-32
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000003809614
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to LAN-22, "CAN Communication Signal Chart".
DTC Logic
DTC DETECTION LOGIC
DTC CONSULT-III display description CAN COMM CIRCUIT DTC Detection Condition When BCM cannot communicate CAN communication signal continuously for 2 seconds or more. Possible cause
INFOID:0000000003809615
U1000
Diagnosis Procedure
INFOID:0000000003809616
BCS
BCS-33
Possible cause
Diagnosis Procedure
1.REPLACE BCM
When DTC U1010: CONTROL UNIT (CAN) is detected, replace BCM. >> Replace BCM. Refer to BCS-78, "Exploded View".
BCS-34
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from the ABS actuator and electric unit (control unit).
DTC Logic
DTC DETECTION LOGIC
DTC CONSULT-III display description VEHICLE SPEED SIG DTC Detection Condition When the vehicle speed signal received from the ABS actuator and electric unit (control unit) remains abnormal for 2 seconds or more. Probable cause
INFOID:0000000003809620
U0415
1.DTC CONFIRMATION
1. 2. 3. Erase the DTC. Turn ignition switch OFF. Perform the Self Diagnostic Result of CONSULT-III, when passed 2 seconds or more after the ignition switch is turned ON. Is any DTC detected? YES >> Refer to BCS-35, "Diagnosis Procedure". NO >> INSPECTION END
INFOID:0000000003809621
Diagnosis Procedure
BCS
BCS-35
1.DTC CONFIRMATION
1. 2. 3. Erase DTC. Turn ignition switch OFF. Perform the Self Diagnostic Result of CONSULT-III, when passed 1.5 seconds or more after the ignition switch is turned ON. Is any DTC detected? YES >> Refer to BCS-36, "Diagnosis Procedure". NO >> INSPECTION END
Diagnosis Procedure
INFOID:0000000003809623
BCS-36
Is the fuse fusing? YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is blown. NO >> GO TO 2.
Is the measurement value normal? YES >> GO TO 3. NO >> Repair harness or connector.
Does continuity exist? YES >> INSPECTION END NO >> Repair harness or connector.
BCS
BCS-37
Continuity
Does continuity exist? YES >> GO TO 2. NO >> Repair the harnesses or connectors.
Does continuity exist? YES >> Repair the harnesses or connectors. NO >> GO TO 3.
Is the measurement value normal? YES >> GO TO 4. NO >> Replace BCM. Refer to BCS-78, "Exploded View".
BCS-38
Is the measurement value normal when any of the switches is turned ON? YES >> Replace BCM. Refer to BCS-78, "Exploded View" NO >> Replace the combination switch.
BCS
BCS-39
Continuity
Does continuity exist? YES >> GO TO 2. NO >> Repair the harnesses or connectors.
Does continuity exist? YES >> Repair the harnesses or connectors. NO >> GO TO 3.
BCS-40
D
JPMIA0041GB
OUTPUT 5
8 1.4 V
Is the measurement value normal when any of the switches is turned ON? YES >> Replace BCM. Refer to BCS-78, "Exploded View" NO >> Replace the combination switch.
BCS
BCS-41
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
INFOID:0000000003809627
Condition Other than front wiper switch HI Front wiper switch HI Other than front wiper switch LO Front wiper switch LO Front washer switch OFF Front washer switch ON Other than front wiper switch INT Front wiper switch INT Front wiper is not in STOP position Front wiper is in STOP position Wiper intermittent dial is in a dial position 1 - 7 Other than turn signal switch RH Turn signal switch RH Other than turn signal switch LH Turn signal switch LH Other than lighting switch 1ST and 2ND Lighting switch 1ST or 2ND Other than lighting switch HI Lighting switch HI Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch PASS Lighting switch PASS Other than lighting switch AUTO Lighting switch AUTO Front fog lamp switch OFF Front fog lamp switch ON Rear fog lamp switch OFF Rear fog lamp switch ON Driver door closed Driver door opened Passenger door closed Passenger door opened Rear RH door closed Rear RH door opened Off On Off On Off On Off On Off On
Value/Status
FR WIPER LOW
FR WASHER SW
FR WIPER INT
Wiper intermittent dial position Off On Off On Off On Off On Off On Off On Off On Off On Off On Off On Off On Off On Off On
TURN SIGNAL L
TAIL LAMP SW
HI BEAM SW
HEAD LAMP SW 1
HEAD LAMP SW 2
PASSING SW
AUTO LIGHT SW
FR FOG SW
RR FOG SW
DOOR SW-DR
DOOR SW-AS
DOOR SW-RR
BCS-42
CDL UNLOCK SW KEY CYL LK-SW KEY CYL UN-SW KEY CYL SW-TR HAZARD SW REAR DEF SW NOTE: At model with BOSE audio system this item is indicated, but is not monitored. TR CANCEL SW TR/BD OPEN SW
D
Off Off Off Off On Off
On
H
NOTE: The item is indicated, but not monitored. Trunk lid opener switch OFF While the trunk lid opener switch is turned ON Trunk lid closed Trunk lid opened LOCK button of the key is not pressed LOCK button of the key is pressed UNLOCK button of the key is not pressed UNLOCK button of the key is pressed TRUNK OPEN button of the key is not pressed TRUNK OPEN button of the key is pressed NOTE: The item is indicated, but not monitored. NOTE: The item is indicated, but not monitored. LOCK/UNLOCK button of the key is not pressed and held simultaneously LOCK/UNLOCK button of the key is pressed and held simultaneously Bright outside of the vehicle Dark outside of the vehicle Driver door request switch is not pressed Driver door request switch is pressed Passenger door request switch is not pressed Passenger door request switch is pressed Off
I
Off On Off On Off On Off On Off On
TRNK/HAT MNTR
RKE-LOCK
RKE-UNLOCK
BCS
Off Off Off
RKE-MODE CHG
O
On Close to 5 V Close to 0 V Off On Off On
OPTICAL SENSOR
REQ SW -DR
REQ SW -AS
BCS-43
PUSH SW
DETE/CANCL SW
SFT PN/N SW
S/L -LOCK
S/L -UNLOCK
S/L RELAY-F/B
PUSH SW -IPDM
DETE SW -IPDM
SFT PN -IPDM
SFT P -MET
SFT N -MET
BCS-44
PRMT ENG STRT PRMT RKE STRT KEY SW -SLOT RKE OPE COUN1 RKE OPE COUN2
CONFRM ID ALL
K
Yet Done Yet
CONFIRM ID4
CONFIRM ID3
BCS
Done Yet Done
CONFIRM ID2
O
Yet Done Yet Done Yet Done
CONFIRM ID1
TP 4
TP 3
BCS-45
TP 1
TERMINAL LAYOUT
JPMIA0062ZZ
BCS-46
Ignition switch OFF Ignition switch OFF Ignition switch ON Interior room lamp battery saver is activated. (Cuts the interior room lamp power supply)
4 (P/W)
Ground
Output
Interior room lamp battery saver is not activated. (Outputs the interior room lamp power supply) UNLOCK (Actuator is activated) Other than UNLOCK (Actuator is not activated) ON OFF LOCK (Actuator is activated)
E
Battery voltage
5 (G/Y)
Ground
Battery voltage 0V
Output
Passenger door
G
0V Battery voltage Battery voltage
7 (R/W)
Ground
Step lamp
Output
Step lamp
8 (V)
Ground
Output
All doors
Other than LOCK (Actua0V tor is not activated) UNLOCK (Actuator is activated) Other than UNLOCK (Actuator is not activated) UNLOCK (Actuator is activated) Other than UNLOCK (Actuator is not activated) Battery voltage 0V Battery voltage
9 (G)
Ground
Output
Driver door
Ground
Rear RH door and rear LH door UNLOCK Battery power supply Ground
Output
K
0V Battery voltage 0V
Ground Ground
Input
Ignition switch OFF Ignition switch ON OFF (LOCK indicator is not illuminated) ACC or ON Turn signal switch OFF
BCS
Ground ACC indicator lamp Output Ignition switch Battery voltage 0V 0V
O
17 (G/B) Ground Turn signal RH (Front and door mirror) Output Ignition switch ON Turn signal switch RH
P
PKID0926E
6.5 V
BCS-47
18 (G/Y)
Ground
Output
Ignition switch ON
PKID0926E
6.5 V 19 (Y) Ground Room lamp timer control Output Interior room lamp OFF ON Turn signal switch OFF Battery voltage 0V 0V
20 (G/B)
Ground
Output
Ignition switch ON
PKID0926E
6.5 V OPEN (Trunk lid opener actuator is activated) Ground Trunk lid opening Output Trunk lid Other than OPEN (Trunk lid opener actuator is not activated) OFF ON Turn signal switch OFF Battery voltage
23 (R)
0V 0V Battery voltage 0V
24 (G)
Ground
Output
25 (G/Y)
Ground
Output
Ignition switch ON
PKID0926E
6.5 V 30 (V/W) Ground Trunk room lamp Output Trunk room lamp OFF ON 0V Battery voltage
BCS-48
B
When Intelligent Key is in the passenger compartment
JMKIA0062GB
34 (B)
Ground
Output
E
When Intelligent Key is not in the passenger compartment
JMKIA0063GB
35 (W)
Ground
Output
J
When Intelligent Key is not in the passenger compartment
JMKIA0063GB
BCS
When Intelligent Key is in the antenna detection area When the trunk lid opener request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
38 (L/O)
Ground
Output
BCS-49
When Intelligent Key is in the antenna detection area When the trunk lid opener request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
39 (BR/W)
Ground
Output
47 (BR/W)
Ground
Output
Ignition switch
OFF or ACC ON
Battery voltage 0V
50 (W)
Ground
Input
JPMIA0011GB
11.8 V ON (When trunk lid opens) Ignition switch ON Ignition switch OFF ON (Pressed) When selector lever is in P or N position When selector lever is not in P or N position 0V Battery voltage 0.3 V 0V 0V
52 (R)
Ground
Output
61 (G/R)
Ground
Input
JPMIA0016GB
1.0 V 64 (GR) Ground Request switch buzzer Output Request switch buzzer Sounding Not sounding 0V Battery voltage
BCS-50
67 (L/R)
Ground
Input
C
Not pressed
D
JPMIA0011GB
11.8 V
68 (R/W)
Ground
Input
JPMIA0011GB
69 (R/B)
Ground
Input
J
JPMIA0011GB
L
When Intelligent Key is in the passenger compartment
JMKIA0062GB
BCS
72 (B/R)
Ground
Output
BCS-51
73 (W/R)
Ground
Output
When Intelligent Key is in the antenna detection area When the passenger door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
74 (B/Y)
Ground
Output
When Intelligent Key is in the antenna detection area When the passenger door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
75 (LG)
Ground
Output
BCS-52
B
When Intelligent Key is in the antenna detection area When the driver door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
76 (V)
Ground
Output
When Intelligent Key is in the antenna detection area When the driver door request switch is operated with ignition switch OFF When Intelligent Key is not in the antenna detection area
JMKIA0063GB JMKIA0062GB
77 (P)
Ground
Output
BCS
When Intelligent Key is in the passenger compartment
JMKIA0062GB
78 (R)
Ground
Output
BCS-53
79 (G)
Ground
Output
Ground
NATS antenna amp (built in key slot) NATS antenna amp (built in key slot) Ignition relay [fuse block (J/B)] control
During waiting
Ignition switch is pressed while inserting the key into the key slot. Ignition switch is pressed while inserting the key into the key slot. OFF or ACC ON
Just after pressing ignition switch. Pointer of tester should move. Just after pressing ignition switch. Pointer of tester should move. 0V Battery voltage
Ground
During waiting
Ground
Ignition switch
During waiting
JMKIA0064GB
83 (L/O)
Ground
Input/ Output
JMKIA0065GB
BCS-54
B
All switch OFF (Wiper intermittent dial 4)
JPMIA0041GB
1.4 V
E
Front fog lamp switch ON (Wiper intermittent dial 4)
F
JPMIA0037GB
87 (R/Y)
Ground
Input
Combination switch
1.3 V
JPMIA0142GB
1.2 V Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 6 Wiper intermittent dial 7
JPMIA0040GB
1.3 V
BCS
BCS-55
JPMIA0041GB
1.4 V
JPMIA0036GB
88 (R/G)
Ground
Input
Combination switch
1.3 V
JPMIA0037GB
1.3 V Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 3 1.3 V 89 (BR) 90 (P) 91 (L) Ground Push-button ignition switch (push switch) CAN-L CAN-H Input Input/ Output Input/ Output Push-button ignition switch (push switch) Pressed Not pressed OFF Battery voltage 0V Battery voltage
JPMIA0040GB
Ground Ground
92 (R/L)
Ground
Output
Blinking
JPMIA0015GB
6.5 V ON 0V
BCS-56
ON indicator lamp
Ground
Output
Ground
Input
Steering lock
Ground
Input
Steering lock
Ground
Input
Selector lever
100 (P/L)
Ground
Input
H
OFF (Not pressed)
I
JPMIA0016GB
1.0 V ON (Pressed) 0V
101 (B/W)
Ground
Input
K
OFF (Not pressed)
L
JPMIA0016GB
1.0 V 102 (Y) 103 (L/R) 106 (G/Y) Ground Blower fan motor relay control Remote keyless entry receiver power supply Steering wheel lock unit power supply Output Ignition switch OFF or ACC ON 0V Battery voltage Battery voltage OFF or ACC ON Battery voltage 0V
BCS
Ground
Output
Ground
Output
Ignition switch
BCS-57
JPMIA0041GB
1.4 V
JPMIA0037GB
1.3 V
107 (R/W)
Ground
Input
JPMIA0036GB
1.3 V
JPMIA0038GB
1.3 V
JPMIA0039GB
1.3 V
BCS-58
B
All switch OFF (Wiper intermittent dial 4)
JPMIA0041GB
1.4 V
E
Lighting switch AUTO (Wiper intermittent dial 4)
F
JPMIA0038GB
108 (P/B)
Ground
Input
Combination switch
1.3 V
JPMIA0036GB
1.3 V Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 5 Wiper intermittent dial 6 1.3 V
K
JPMIA0039GB
BCS
BCS-59
JPMIA0041GB
1.4 V
JPMIA0037GB
1.3 V
109 (R/B)
Ground
Input
JPMIA0036GB
1.3 V
JPMIA0038GB
1.3 V
JPMIA0040GB
1.3 V ON 0V
110 (G/O)
Ground
Hazard switch
Input
Hazard switch
OFF
JPMIA0012GB
1.1 V
BCS-60
C
LOCK or UNLOCK 111 (L/Y) Ground Steering lock unit communication Input/ Output Steering lock
D
JMKIA0066GB
For 15 seconds after UNLOCK 15 seconds or later after UNLOCK 113 (P/B) Ignition switch ON When bright outside of the vehicle When dark outside of the vehicle OFF ACC
Battery voltage 0V
F
Close to 5 V Close to 0 V 0V 5.0 V
Ground
Optical sensor
Input
115 (L)
Ground
Shock sensor
Input
Ignition switch ON
J
JPMIA1034GB
2.5 V 116 (R/W) 118 (O/L) Ground Fuse check (Stop lamp switch) Input OFF (Brake pedal is not depressed) ON (Brake pedal is depressed) Battery voltage 0V
Ground
Input
L
Battery voltage
BCS
119 (G/W)
Ground
Input
Driver door
JPMIA0012GB
1.1 V UNLOCK status (unlock sensor switch ON) 121 (Y) 122 (V/R) 123 (G/W) Ground Key slot switch Input When the key is inserted into key slot When the key is not inserted into key slot Ignition switch OFF ACC or ON OFF or ACC ON 0V Battery voltage 0V 0V Battery voltage 0V Battery voltage
Ground
ACC feedback
Input
Ground
IGN feedback
Input
Ignition switch
BCS-61
124 (R/B)
Ground
Input
JPMIA0011GB
128 (GR)
Ground
Input
Door lock and unlock switch [power window main switch or front power window switch (passenger side)]
NEUTRAL position
JPMIA0011GB
130* (GR/W)
Ground
Input
Ignition switch ON
JPMIA0012GB
131 (GR/R)
Ground
Input
Door lock and unlock switch [power window main switch or front power window switch (passenger side)]
NEUTRAL position
JPMIA0011GB
11.8 V UNLOCK position 0V 9.5 V 0V Battery voltage 0V 0V OFF 0V 5.0 V Battery voltage 0V
133 (W) 134 (R) 137 (P) 138 (V/W) 140 (R/G)
Ground
Push-button ignition switch illumination LOCK indicator lamp Receiver and sensor ground Receiver and sensor power supply output Selector lever P/N position
Output
ON OFF OFF ON
Ground Ground
Output Input
Ground
Output
Ignition switch
Ground
Input
Selector lever
BCS-62
141 (L/O)
C
Ground Security indicator Output Security indicator Blinking
D
JPMIA0014GB
11.3 V OFF All switch OFF Lighting switch 1ST Combination switch (Wiper intermittent dial 4) Lighting switch HI Lighting switch 2ND Battery voltage 0V
142 (LG/B)
Ground
Output
G
Turn signal switch RH
JPMIA0031GB
10.7 V All switch OFF (Wiper intermittent dial 4) Front wiper switch HI (Wiper intermittent dial 4) Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 3 Wiper intermittent dial 6 Wiper intermittent dial 7 All switch OFF (Wiper intermittent dial 4) Front washer switch ON (Wiper intermittent dial 4) 144 (G/B) Ground Combination switch OUTPUT 2 Output Combination switch Any of the conditions below with all switch OFF Wiper intermittent dial 1 Wiper intermittent dial 5 Wiper intermittent dial 6 0V 0V
143 (L/W)
Ground
Output
Combination switch
K
JPMIA0032GB
10.7 V
BCS
O
JPMIA0033GB
10.7 V
BCS-63
145 (LG/R)
Ground
Output
10.7 V All switch OFF Front fog lamp switch ON Combination switch (Wiper intermittent dial 4) Lighting switch 2ND Lighting switch PASS 0V
146 (G/Y)
Ground
Output
10.7 V
150 (SB)
Ground
Input
JPMIA0011GB
11.8 V ON (When driver door opens) 151 (G/R) NOTE: *: Without BOSE audio system Ground Rear window defogger relay Output Rear window defogger Active Not activated 0V 0V Battery voltage
BCS-64
INFOID:0000000003809628
BCS
JCMWM1671GB
BCS-65
JCMWM1672GB
BCS-66
BCS
O
JCMWM1673GB
BCS-67
JCMWM1674GB
BCS-68
BCS
O
JCMWM1675GB
BCS-69
JCMWM1676GB
BCS-70
BCS
O
JCMWM1677GB
Fail-safe
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC is detected.
P
INFOID:0000000003809629
BCS-71
B2604: PNP SW
B2605: PNP SW
BCS-72
Maintains the power supply position attained at the time of DTC detection
B2617: STARTER RELAY CIRC B2618: BCM B2619: BCM B261E: VEHICLE TYPE B26E1: ENG STATE NO RES
Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking Inhibit engine cranking
L BCM detects the turn signal lamp circuit status by the current value. BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal lamp operating. BCS NOTE: The blinking speed is normal while activating the hazard warning lamp.
INFOID:0000000003809630
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart.
O
Priority 1 2 B2562: LOW VOLTAGE U1000: CAN COMM CIRCUIT U1010: CONTROL UNIT (CAN) B2190: NATS ANTENNA AMP B2191: DIFFERENCE OF KEY B2192: ID DISCORD BCM-ECM B2193: CHAIN OF BCM-ECM DTC
BCS-73
DTC Index
NOTE: The details of time display are as follows. CRNT: A malfunction is detected now. PAST: A malfunction was detected in the past. IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data and IGN Counter, refer to BCS-16, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
CONSULT display No DTC is detected. further testing may be required. U1000: CAN COMM CIRCUIT U1010: CONTROL UNIT (CAN) U0415: VEHICLE SPEED SIG B2013: ID DISCORD BCM-S/L B2014: CHAIN OF S/L-BCM B2190: NATS ANTENNA AMP B2191: DIFFERENCE OF KEY Fail-safe Freeze Frame Data Intelligent Key warning lamp ON Reference page
BCS-74
BCS
SEC-95 DLK-50 DLK-52 DLK-54 SEC-82 SEC-83 SEC-84
BCS-75
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom Table
1. 2. Perform Data Monitor of CONSULT-III to check for any malfunctioning item. Check the malfunction combinations.
Malfunction item:
INFOID:0000000003809632
Data monitor item HEAD LAMP SW 1 HEAD LAMP SW 2 AUTO LIGHT SW FR WASHER SW TURN SIGNAL R TURN SIGNAL L FR WIPER LOW TAIL LAMP SW FR WIPER INT PASSING SW FR WIPER HI INT VOLUME HI BEAM SW RR FOG SW FR FOG SW
Malfunction combination
A B C D E F G H I J K L
All Items
If only one item is detected or the item is not applicable to the combinations A to K
3.
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction combination A B C D E F G H I J K L Malfunctioning part Combination switch INPUT 1 circuit Combination switch INPUT 2 circuit Combination switch INPUT 3 circuit Combination switch INPUT 4 circuit Combination switch INPUT 5 circuit Combination switch OUTPUT 1 circuit Combination switch OUTPUT 2 circuit Combination switch OUTPUT 3 circuit Combination switch OUTPUT 4 circuit Combination switch OUTPUT 5 circuit BCM Combination switch Replace BCM. Refer to BCS-78, "Exploded View". Replace the combination switch. Inspect the combination switch output circuit applicable to the malfunctioning part. Refer to BCS-40, "Diagnosis Procedure". Inspect the combination switch input circuit applicable to the malfunctioning part. Refer to BCS-38, "Diagnosis Procedure". Repair or replace
BCS-76
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
INFOID:0000000003809633
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. Information necessary to service the system safely is included in the SRS AIRBAG and SEAT BELT of this Service Manual. WARNING: To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS AIRBAG. Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
BCS
BCS-77
ON-VEHICLE REPAIR
BCM (BODY CONTROL MODULE)
Exploded View
INFOID:0000000003809634
CAUTION: Before replacing BCM, perform READ CONFIGURATION to save or print current vehicle specification. Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description".
JPMIA1038ZZ
1.
BCM
INFOID:0000000003809635
CAUTION: Before replacing BCM, perform READ CONFIGURATION to save or print current vehicle specification. Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Description".
REMOVAL
1. 2. 3. Remove combination meter. Refer to MWI-126, "Exploded View". Remove screws. Remove BCM and disconnect the connector.
INSTALLATION
Install in the reverse order of removal. CAUTION: Be sure to perform WRITE CONFIGURATION when replacing BCM. Be sure to perform the system initialization (NATS) when replacing BCM. Refer to BCS-3, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) : Special Repair Requirement".
BCS-78
COMBINATION SWITCH
< ON-VEHICLE REPAIR >
COMBINATION SWITCH
Exploded View
INFOID:0000000003809636
F
JPMIA1039ZZ
1.
Combination switch
2.
INSTALLATION
Install in the reverse order of removal.
K
BCS
BCS-79