Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
1/4
Toe Only
Typ 1/4 1/4 5/16 5/16 10" 1'-2 1/2" Typ 1'-7 1/2" PL3/4"-A572-Gr50
1'-7 1/2"
W12X152
8''
9"
0.905
1/4
2 - 3/4" A325-N Bolts (Typ) Gage = 5.5" Provide 2" slotted holes at the gusset seat and stabilizer angle
5/16
Page 1 of 11
= = = =
210.0 160.0
kips kips
W12X87 = = = = = = = 50 65
W12X152 = = = = = = = = 50 65
Page 2 of 11
Calculations:
Brace-to-gusset weld
Weld Capacity Rn/! where: Rn/! Fu = D= Thus lw = 22.63 in > 70 210 ksi 5/16 in = !=2 2 x 0.6Fu 0.707D lw
Distribute weld Weld at angle toe = Weld at angle heel = 10.00 22.63 - 10 in = 12.63 say 14.50
Page 3 of 11
= =
Whitmore section
Lw = 2 lw tan 30 + B Lw = 17.547 in 0.000 0.000 in in B= 6.00 in
! = 1.67
Rn = 50 x [ ( 17.547 - 0 - 0 ) x 0.75 ] + 50 x (0 x 0.515) Rn = Rn/! 658.01 = kips kips > 210.00 kips (OK)
394.02
2 x Min[ (0.6 x Fu x Anv + Ubs x Fu x Ant); (0.6 x Fy x Agv + Ubs x Fu x Ant) ] Where: Ubs = 1.0 Ant = Net Area with Tension Resistance = Bbrace x tgusset = 4.50 in
2
kips
>
210.00
kips
(OK)
Page 4 of 11
! = 1.67
>
210.00
kips
(OK)
! = 2.00
U = 1 - x/L U= 0.833
Ae = U An Rn/! = 277.81
= kips
9.580 >
in
210.00
kips
(OK)
Rn/!
= where:
!=2
>
140.9
0.240
in
Page 5 of 11
= =
1/4
in fillet weld
9"
x x
y= y=
2L x L/2 2L + 2x 8.290 in
Ix =
Ix = Sx = Sx =
Rnw/!
= where:
(! = 2.0)
Fu = w= =
70
ksi in degrees
5/16 0
Thus
Page 6 of 11
Solving for the resultant force [Rnw/!] = [ Ra e / Sx ] + [ Ra / (2x +2L) ] where: L= B' = B' = e= e= Thus, Ra = 196.54 kips > 160.00 kips (OK) 20 in
Determine weld requirement for seat plate to stiffener plate Use 5/16 weld to develop the weld between the seat plate and the column web. Check weld length 10.00 in > 4.125 kips (OK)
Determine the stiffener plate thickness Minimum plate thickness to develop the stiffener-to-seat weld tmin = 2w = 0.625 in
Minimum plate thickness to develop the top chord web tmin = tmin = thus, tmin = max( 0.625 , 0.515 ) tmin = 0.625 in < 0.75 in (OK) 50.0 50.0 0.52 tw
Page 7 of 11
>
160.00
kips
(OK)
Minimum column web thickness to develop the weld twmin twmin > =
3.09 D Fu
3.09 x 0.3125 65
0.24
in
<
0.87
in
(OK)
50
ksi
PL3/4"-A572-Gr50
Built-up Section Compressive Capacity Since KL/2 Pn Pn/! = = < Fy A 550.150 25 ,section J4.4 of AISC 360-05 applies. (! = 1.67) kips > 160.00 kips (OK)
Rn/!
= where:
> 19.50 70 0
58.8 in
kips
ksi degrees
in
7.88
sixteenths
Page 9 of 11
= =
1/4
in fillet weld
Rn = (N + 2.5k) x Fy x tw Rn = [ (8 - 0.75) + 2.5(1.41) ] x 50 x 0.515 Rn = kips 277.46 Rn/! = 184.97 kips > 160.00 kips (OK)
Web Crippling
!=2
Page 10 of 11
Page 11 of 11