THE ROAD TRIP PILLOW CASE
What you need:
1 yard of fabric (42 inches wide!
22 inches of cotton webbing
2-16 X 12 pieces of fabric for the pocket
3 inch piece of Velcro
42 inches of rick rack or ribbon
1 piece of craft felt
Wonder Under
Template for initial
Matching thread
1. Lay fabric out flat with the right side facing up
The 36 inches (1 yard of fabric) is the width of the
pillow case and the 42 incheg will be the length folded
in half.
2. Serge or zig zag stitch down the right side of the
fabric.
i — Serge ov Fig ay) ite
3. Now with the wrong side of the fabric facing up, take
the end you just serged and fold over 4 inches and iron
the seam. Stitch in place right up against the edge with
a % inch seam.
4. Turn fabric over so the right side is facing up and
pin your rick rack or ribbon on the 4” seam. Sew the
rick rack down along this seam
Viget ide
Vibben ov Viele vac.5. Take the 2 pieces of fabric for the pocket (both 16 x
12) and pin right sides together. Stitch all the way
around with a %"seam leaving a 3 inch gap on one side for
turning.
6. Turn the pocket right side in and press seams
7. Top stitch 4“down on the side that will be at the top
eal
8. Iron the Wonder Under on to the piece of craft felt.
Cut the child’s initial out of the felt. I usually print
up the initial that takes up most of the page on my word
program (depending on which font you use it can be as
large as 675) and then place it on the back of the Wonder
Under backwards and trace around it in pencil. Then, I
cut from there.
9, Iron this on to the front of the pocket closer to the
bottom to leave room for the Velcro at the top. Zig zag
stitch around the letter. I
10. Place the 3 inch piece of Velcro centered on the
inside of the pocket approx. 6 %” from each side and
about %” down from the top. Stitch around the piece of
Velcro with a small zig zag stitch,
= yelevo
[Rr
11. Take your pillow case fabric with the wrong side
facing up and fold in half length wise with the fold on
the bottom. Sew the left ends together with a 5/8” seam.
If not using a serger, zig zag this stitch afterwards
Don’t sew the top pieces of fabric together yet. Now
turn it right side out.12. With the fold on the bottom and the left seam sewn
it’s time to sew the pocket on to the front. Measure 3
inches from the bottom and approx. 6 4” from the left to
place to pocket. That will leave approx. 9” to the end
of the pillow case opening on the right. Pin to the top
layer only and sew all the way around with a }” seam
Make sure to only _sew it top layer
13. Pin the 2" half of the Velcro to the pillow case
fabric where it will meet the Velcro from the pocket.
Sew all the way around the piece of Velcro with a small
zig zag stitch. Vight side
#€ Neleve
14. For the handle use the 22” piece of cotton webbing.
For placement, line it up with the edges of the pocket
and pin so that it lays in between the 2 pillowcase
layers and isn’t twisted
15. Turn inside out one more time and sew the top of the
pillow case catching the cotton webbing with a 5/8” seam.
If not using a serger, then zig this after you stitch
Bee enteral Catton wedding ic in
between |: Fourehin.
Me vii Wi bikes FF 5
Ame fabric, .
16. Turn it right side out and fill the pocket with all
sorts of good books, puzzles, games, crayons, etc. that
will keep your child entertained during a road trip