Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
Typical Applications
B deflector lug mandrels are designed for dual-string installations and are also normally used in injectionpressure-operated tubing flow applications. These mandrels feature long, tapered lugs welded in line with the exterior ported lug to protect the installed subsurface control device and allow the material to easily pass other mandrels during installation in string applications
BJR
1 12/06/00
Typical Applications
Camco reverse flow check valves require flow to close. As the differential pressure across the valves check dart increases, the dart contacts the soft seat and then the hard seat to form a seal and close the check valve. These valves each have an elastomeric soft seat and stainless steel hard seat. The initial seal is between the valves stainless steel check dart and the soft seat. These check valves can withstand 10,000 psi differential pressure and can be converted from velocity check valves to positive check valves by the addition of a spring. The flow area for the 1m OD B-1 valve is equivalent to a 5/16 port.
2 12/06/00
BJR
Typical Applications
The BEK Latch is installed and removed from the mandrel pocket using standard slickline methods. A minimum amount of force is required to install the latch. This is particularly important in deviated wells where forceful downward jarring is not possible. The latch components are available in either stainless steel or nickel alloys for corrosion resistance in wells with high concentrations of Hydrogen Sulfide and / or Carbon Dioxide. The Camco BEK latch secures 1 OD side pocket devices in Camco KB series side pocket mandrels. The latch is used when flow through the latch is desired. The BEK-3 is used when an erosion-resistant bore is desired.
3 12/06/00
BJR
Typical Applications
1/8 - 5/16 port sizes The bellows of the BK-1 gas lift valve is constructed of three-ply Monel. During manufacture, the bellows is subjected to a special hydraulic forming process to seat all the convolutions of the bellows so that each convolution accepts an equal amount of stress during valve operation.
4 12/06/00
BJR
Typical Applications
The bellows of the BK gas lift valve is constructed of three-ply Monel. During manufacture, the bellows is placed in a hydrostatic pressure chamber and subjected to external pressure. This special hydraulic forming process seats all the convolutions of the valve bellows so that each convolution accepts an equal amount of stress during valve operation. The component parts of the bellows assembly are unitized by induction brazing that enables the nitrogen charge to be sealed in the bellows without the use of 5 elastomers. 12/06/00 BJR
Camco BK - 2 Latch
Typical Applications
BJR
Typical Applications
The BKCI-2 valve offers metal seal nitrogen containment technology. Instead of the conventional bellows type design, the BKCI-2 uses a two-way metal seal piston for operation. Silicone fluid is maintained above the piston and acts as a barrier between the gas dome charge and sealing lips of the piston, which enables the valve to maintain nitrogen dome pressures to 10, 000psi. Friction characteristics of the BKCI-2 are different from those observed on bellows operated valves. Once opening pressure is achieved, the piston will travel to the fully open position and allow maximum flow. Friction between the piston and housing acts as a buffer to help prevent valve chatter.
7 12/06/00
BJR
Typical Applications
The BKEO equalizing dummy valve is available in stainless steel and high nickel alloys for use in corrosive environment. Sealing materials are utilized to allow the valve to be used in standard to high temperature conditions. The BKEO valve is installed in the mandrel either at the surface prior to running the completion or by standard slickline methods after the mandrels have been installed in the well. To equalize pressure between the tubing and casing annulus during pulling operations.
8 12/06/00
BJR
Typical Applications
The BKF-12 is bellows actuated, spring loaded and and normally closed. The valve components are available in either stainless steel or nickel alloys for corrosion resistance in wells with high concentrations of Hydrogen Sulfide and/or Carbon Dioxide. The metal used conforms to NACE standard MR0175 for sulfide stress cracking resistant metallic materials.
9 12/06/00
BJR
FEATURES Large flow area For circulation in either direction Utilizes ported BEK-2 or BEK-3 type latch Simple design, modular construction Available in various alloys and elastomers Optional choke sizes (1/16 - 7/16) APPLICATION AND OPERATION Corrosion resistant materials are available for use in wells with high concentration of H2S and/or CO2. Various sealing
10 12/06/00
BJR
11 12/06/00
BJR
FEATURES Standard API connections and grades Robust construction Accepts standard 1-1/2 conventional gas lift valves and checks
12 12/06/00
BJR
mandrel with the EC feature for annular lift, the BKO-3 valve controls flow from the tubing to the casing. The valve
consists of two primary housing components, a floating seat, a check dart, a valve nose, and two sets of external packing.
FEATURES Simple design, modular construction Available in various alloys Many packing materials available Wide selection of orifice sizes (1/8 - 5/16) Integral reverse check
13 12/06/00 BJR
FEATURES Integral bottom latch Simple design, modular construction Available in various alloys Many packing materials available Unitized bellows nitrogen containment
14 12/06/00 BJR
tungsten carbide seats, high temperature/high pressure packing and high temperature o-ring seals with back-ups.
FEATURES Solid tungsten carbide valve seat Integral bottom latch and reverse check Equipped with high temperature/high pressure seals Unitized bellows nitrogen containment 1/8 - 3/8 port sizes
15 12/06/00
BJR
FEATURES Standard API connections and grades Robust construction APPLICATION AND OPERATION BR deflector lug mandrels are designed for either singlestring or dual-string installations and are normally used in production-pressure-operated tubing flow applications. These mandrels, like B deflector lug mandrels, feature long, tapered, welded-on lugs for use in dual-string installations. The exterior ported lug on the BR deflector lug mandrels,
16 12/06/00 BJR
17 12/06/00
BJR
concentrations of H2S and/or CO2, or to eliminate paraffin, salt and/or hydrate formation in the tubing string and flow lines. The valve makes possible precise control of injection volumes and treatment of well fluid at valve depth.
FEATURES Valve components constructed from stainless steel or nickel alloys Spring loaded operation Various packing materials available Standard 3/16 port
18 12/06/00
BJR
FEATURES Simple rugged design Available in various alloys Various packing material available
19 12/06/00
BJR
FEATURES Integral reverse check Includes hard and soft seats Available in standard or premium materials APPLICATION AND OPERATION Camco reverse flow check valves require flow to close. As the differential pressure across the valves check dart
20 12/06/00
BJR
Injection Valve is a 1 OD slickline retrievable device used to control subsurface corrosion in wells with high concentrations of H2S and/or CO2, or to eliminate paraffin, salt and/or hydrate formation in the tubing string and flow lines. The valve makes possible precise control of injection volumes and treatment of well fluid at valve depth.
FEATURES Valve components constructed from stainless steel or nickel alloys Spring loaded operation Various packing materials available Standard 3/16 port
21 12/06/00
BJR
FEATURES Standard API connections and grades Robust construction Accepts standard 1-1/2 conventional gas lift valves and checks APPLICATION AND OPERATION CR deflector lug mandrels are designed for either singlestring or dual-string installations and are normally used in
22 12/06/00
BJR
FEATURES Large flow area For circulation in either direction Integral bottom latch Simple design, modular construction Available in various alloys and elastomers APPLICATION AND OPERATION Corrosion resistant materials are available for use in wells with high concentration of H2S and/or CO2. Various sealing
23 12/06/00 BJR
FEATURES Integral bottom latch Rugged solid construction Available in stainless steel or high nickel alloys Various packing materials available
24 12/06/00
BJR
mandrel with the EC feature for annular lift, the DKO-2 valve controls flow from the tubing to the casing. The valve consists of a running head and two packing barrels, check housing, a fixed orifice, an integral reverse flow check element, an integral bottom latch, and two sets of external packing.
FEATURES Integral bottom latch and reverse check Wide selection of orifice sizes (1/8 - 3/8) Convertible to casing flow operation Available in various alloys and elastomers
25 12/06/00
BJR
FEATURES Rugged, solid construction Available in stainless steel or high nickel alloys Various packing materials available Accepts top latch
26 12/06/00
BJR
FEATURES Integral latch Open porting for circulation after equalization Circulating area equivalent to 1/4" diameter Available in various alloys and elastomers
27 12/06/00
BJR
FEATURES Simple, design modular construction Integral bottom latch Various packing materials available
28 12/06/00
BJR
reached, the spring is compressed, causing the variable orifice to begin closing, thus maintaining a constant flow rate independent of pressure variations.
FEATURES Rugged back check system** Integral inlet filter Rugged, solid construction Available in stainless steel or high nickel alloys Various packing materials available
29 12/06/00
BJR
Regulator consists of a fixed calibrated orifice mounted on a spring-dampened stem, acting together as a variable orifice. The calibrated orifice allows a predetermined water flow to pass when a minimum pressure differential is attained. When this minimum pressure differential is
reached, the spring is compressed, causing the variable orifice to begin closing, thus maintaining a constant flow rate independent of pressure variations.
FEATURES Rugged back check system Integral inlet filter Rugged, solid construction Available in stainless steel or high nickel alloys Various packing materials available
30 12/06/00
BJR
FEATURES Integral reverse check Includes hard and soft seats Available in standard or premium materials APPLICATION AND OPERATION Camco reverse flow check valves require flow to close. As the differential pressure across the valves check dart
31 12/06/00
BJR
FEATURES Conventional type valve Nitrogen charged bellows Floating seat to promote positive stem/seat Injection pressure operated Dual seat nitrogen containment Special bellows treatment to prolong life Available in various alloys and elastomers 3/16 1/2 port sizes
32 12/06/00 BJR
FEATURES Conventional type valve Nitrogen-charged bellows Floating seat to promote positive stem/seat Injection pressure operated Dual seat nitrogen containment Special bellows treatment to prolong life Available in various alloys and elastomers 1/8 3/8 port sizes
33 12/06/00 BJR
FEATURES Solid one-piece construction Accepts 5/8 OD gas lift valve Available in 1.315 2.875 sizes Available with API or premium connections APPLICATION AND OPERATION Camco macaroni mandrels provide a means to install subsurface control devices in tubingless completions. Tubingless completions are those in which two or more macaroni tubing strings are installed in the wellbore and
34 12/06/00 BJR
charged, and normally closed. The simplicity of the J-50 design assures a long operating life.
FEATURES Conventional type valve Nitrogen charged bellows Floating seat to promote positive stem/seat Injection pressure operated Dual seat nitrogen containment Special bellows treatment to prolong life Integral reverse check 1/8 - 3/8 port sizes
35 12/06/00
BJR
FEATURES Crossover seat design Unitized bellows nitrogen containment Simple design, modular construction Available in various alloys and elastomers Port sizes 1/8 1/4 APPLICATION AND OPERATION The bellows of the JR-20 Gas Lift Valve is constructed of three-ply Monel. During manufacture, the bellows is placed
36 12/06/00 BJR
FEATURES Crossover seat design Unitized bellows nitrogen containment Simple design, modular construction Available in various alloys and elastomers Port sizes 1/8 3/16 APPLICATION AND OPERATION The bellows of the JR-40 Gas Lift Valve is constructed of three-ply Monel. During manufacture, the bellows is placed
37 12/06/00 BJR
mandrels are designed with a round cross section and are available in a variety of tubing sizes and thread types.
FEATURES Single 1 pocket round mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Solid bar pocket and discriminator construction Pressure rating approaches or equals that of tubing
38 12/06/00
BJR
39 12/06/00
BJR
FEATURES Single 1" pocket oval mandrel Smooth internal/external shoulders Tubular pocket and integral tool discriminator Patented positioning sleeve orienting system Integrally forged swages through 3-1/2" size
40 12/06/00
BJR
FEATURES Single 1 pocket round mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Solid bar pocket and discriminator construction Pressure rating approaches or equals that of tubing
41 12/06/00
BJR
proportional response gas lift valve used for high gas volume and high-pressure continuous flow gas lift
installations. The proportional response of these valves enable Schlumberger gas lift engineers to accurately calculate the gas injection volumes required throughout the entire range of operating conditions of the well.
FEATURES Specialized bellows design Combination spring and charged dome Throttling type design Hydrostatic and vibration protection for the bellows Available in various alloys and elastomers Port sizes 1/8 1/4"
42 12/06/00
BJR
proportional response gas lift valve used for high gas volume and high-pressure continuous flow gas lift
installations. The proportional response of these valves enable gas lift engineers to accurately calculate the gas injection volumes required throughout the entire range of operating conditions of the well.
FEATURES Specialized bellows design Combination spring and charged dome Throttling type design Hydrostatic and vibration protection for the bellows Available in various alloys and elastomers Port sizes 1/8 1/4"
43 12/06/00
BJR
FEATURES Single 1-1/2 pocket oval mandrel Forged oval pocket and tool discriminator Patented positioning sleeve orientation system Smooth internal and external surfaces Integrally forged swages through 3-1/2 size APPLICATION AND OPERATION Designed with eccentric swages on both ends, these mandrels are available in a variety of thread types and
44 12/06/00 BJR
FEATURES Single 1-1/2 pocket oval mandrel Patented positioning sleeve orientation system Tool discriminator Bottom snorkel on pocket Pressure rating approaches or equals that of tubing
45 12/06/00
BJR
FEATURES Single 1-1/2 pocket oval mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Integral injection line connection Pressure rating approaches or equals that of tubing APPLICATION AND OPERATION The metallurgical properties of the steel used are closely controlled through rigid specifications. The mandrels for
46 12/06/00
BJR
mandrels are designed with an oval cross section and feature a 1-1/2 bore pocket. FEATURES Single 1-1/2 pocket oval mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Integral injection line connection Pressure rating approaches or equals that of tubing APPLICATION AND OPERATION The metallurgical properties of the steel used are closely controlled through rigid specifications. The mandrels for
47 12/06/00
BJR
FEATURES Single 1-1/2 pocket oval mandrel with smooth internal and external surfaces
48 12/06/00
BJR
FEATURES Single 1-1/2 pocket oval mandrel Tubular pocket and tool discriminator Patented positioning sleeve orientation system Integrally forged swages through 3-1/2" size Smooth internal/external shoulders
49 12/06/00
BJR
mandrels are designed with a round cross section and are available in a variety of tubing sizes and thread types.
FEATURES Single 1-1/2 pocket round mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Solid bar pocket and discriminator construction Pressure rating approaches or equals that of tubing APPLICATION AND OPERATION Standard Camco side pocket mandrels are manufactured from high quality low alloy steel.
50 12/06/00
The metallurgical
BJR
FEATURES Single 1-1/2 pocket round mandrel Specially designed robust guard rail and control line protection system Extended swages for remachining of threads Patented positioning sleeve orientation system Smooth internal/external shoulders Solid bar pocket and discriminator construction Pressure rating approaches or equals that of tubing
51 12/06/00
BJR
FEATURES Single 1-1/2 pocket round mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Solid bar pocket and discriminator construction Pressure rating approaches or equals that of tubing Specially designed robust guard rail and control line protection system
52 12/06/00
BJR
mandrels feature a specially designed receiver pocket to accept Camco RA and RM latches.
FEATURES Single 1-1/2 pocket round mandrel Patented positioning sleeve orientation system Smooth internal/external shoulders Insert pocket and discriminator Pressure rating approaches or equals that of tubing
53 12/06/00 BJR
FEATURES Made from hard, corrosion resistant materials Provides expert gas lift design and support by specialist Provides focus on stabilization strategy and flow stabilization by critical flow through injection point Provides computer enhanced flow profiling
54 12/06/00 BJR
FEATURES Orifice venturi made from hard, corrosion resistant materials Body parts constructed from stainless steel or high nickel alloys Various packing materials are available
55 12/06/00
BJR
installed in a M series mandrel, the O-21R is used to control the flow of gas from the casing annulus to the tubing. When installed in a M series mandrel with the EC feature for annular lift, the O-21R valve controls flow from the tubing to the casing.
FEATURES Simple design, modular construction Wide selection of orifice sizes (1/8 5/8) Integral spring loaded reverse check Available in various alloys and elastomers
56 12/06/00
BJR
FEATURES Dual spring loaded reverse checks Simple design, modular construction Available in various alloys and elastomers Wide selection of orifice sizes (1/16 5/8) APPLICATION AND OPERATION The O2-30R orifice valve is constructed from stainless steel or nickel alloys for corrosion resistance in wells with high
57 12/06/00
BJR
FEATURES Simple design, modular construction Available in various alloys Many packing materials available Wide selection of orifice sizes (1/8 7/16) Integral reverse check
58 12/06/00
BJR
FEATURES Large port for maximum efficiency Adjustable tubing sensitivity High slug lifting capacity Preset spring compression Port sizes 1/8 - 5/16
59 12/06/00
BJR
FEATURES Nitrogen charged three-ply bellows Floating seat to promote positive stem/seat alignment Injection pressure operated Dual back check system Rugged, solid construction Available in stainless steel or high nickel alloys Various packing materials available 1/8 - 1/2 port sizes
60 12/06/00 BJR
valve is used to enhance production by injecting highpressure gas from the casing/tubing annulus, into the production fluid. Carefully controlled quantities of gas
lighten the fluid column allowing natural reservoir pressure to push the fluid up the tubing.
FEATURES Externally adjusted spring Cross-over seat design Integral reverse check Simple design, modular construction Available in various alloys and elastomers Unitized bellows nitrogen containment
61 12/06/00 BJR
Camco RA Latch
INTRODUCTION The Camco* RA latch is a 1-1/2 OD retrievable valve top latch which anchors Camco retrievable gas lift valves and side pocket accessories in the appropriate M series Camco side pocket mandrels with an A-Type pocket. This latch is designed with a spring-loaded rotating latch cam.
FEATURES Rugged field proven design Cam type latch Available in stainless steel or high nickel alloys APPLICATION AND OPERATION The RA latch is installed and removed from the mandrel pocket using standard slickline methods. amount of force is required to install the latch. A minimum
62 12/06/00
BJR
FEATURES Valve constructed from stainless steel or nickel alloys Nitrogen charged bellows operation Various packing materials available APPLICATION AND OPERATION The bellows of the RCB chemical injection valve is constructed of three-ply Monel and is designed and
64 12/06/00
BJR
possible control of injection volumes and treatment of well fluid at valve depth.
FEATURES Modular design, rugged, solid construction Available in stainless steel or high nickel alloys Various packing materials available Dual, spring-loaded positive check APPLICATION AND OPERATION The RCDC chemical injection valve is a fully open valve with two spring loaded positive checks. Injection flow and fluid
65 12/06/00
BJR
mandrel with the EC feature for annular lift, the RDO-5 valve controls flow from the tubing to the casing. The valve
consists of two primary housing components, a floating seat, an integral reverse flow check element, a valve nose and two sets of external packing.
FEATURES Simple design, modular construction Available in various alloys Many packing materials available Wide selection of orifice sizes (3/16 - 3/4) Integral reverse check
67 12/06/00 BJR
components, a ported valve seat, two integral reverse flow check darts, a valve nose and two sets of external packing.
FEATURES Annulus to tubing circulation Circulates out top and bottom Large flow area (0.392 sq. in.) Integral reverse checks APPLICATION AND OPERATION The RG-2 circulating valve with RKP latch is installed in a mandrel prior to circulation. The RG-2 valve has a flow area equivalent to a 45/64 port. The special design through both
68 12/06/00
BJR
FEATURES Tubing to annulus circulation Circulates through top and bottom Large flow area Integral reverse checks APPLICATION AND OPERATION The RGR-2 with the RKP latch is installed in the mandrel prior to circulation. The RGR-2 has a flow area equivalent to a 45/64 port. The special design of the RGR-2 valve
69 12/06/00
BJR
FEATURES Rugged, solid construction Available in stainless steel or high nickel alloys Various packing materials available Port sizes to 3/8 APPLICATION AND OPERATION The RIPC valve can be equipped with a floating seat (orifice) to 3/8 port size. The bellows of the RIPC gas lift valve is constructed of three ply Monel. During manufacture, the bellows is placed in a hydrostatic pressure chamber and subjected to external
70 12/06/00 BJR
Camco RK Latch
INTRODUCTION The Camco* RK latch is a 1-1/2 OD, spring loaded, ringstyle latch that anchors Camco retrievable gas lift valves and side pocket accessories in the appropriate Camco M series mandrels.
FEATURES Compact and simple latch ring design Minimum amount of force to install in deviated wells Latch components are made of premium materials for stress cracking resistance Pocket debris barrier APPLICATION AND OPERATION The RK latch is installed and removed from the side pocket mandrel using standard slickline methods. A minimum
71 12/06/00
BJR
FEATURES Integral latch Open porting for circulation after equalization Available in various alloys and elastomers Port sizes 5/16 - 1/2
72 12/06/00
BJR
FEATURES Compact and simple ring type design Minimum amount of force is necessary to install Latch components are made from stainless steel or high nickel alloys APPLICATION AND OPERATION The RKP latch is installed and removed from the mandrel pocket using standard slickline methods.
73 12/06/00
A minimum
BJR
Camco-Merla RM Latch
INTRODUCTION The Camco-Merla* RM latch is a 1-1/2 OD spring loaded, dog-style latch that anchors Camco retrievable gas lift valves and side pocket accessories in the appropriate Camco MMA, MMARG or MTA mandrels. The RM latch features an o-ring on the latch stop which provides a debris barrier in the top of the mandrel pocket.
FEATURES Compact and simple dog type design Minimum amount of force is necessary to install Latch components are made from stainless steel or high nickel alloys APPLICATION AND OPERATION The RM latch is installed and removed from the side pocket mandrel using standard slickline methods. A minimum
BJR
FEATURES Compact and simple dog type design Minimum amount of force is necessary to install Latch components are made from stainless steel or high nickel alloys APPLICATION AND OPERATION The RMP latch is installed and removed from the side pocket mandrel using standard slickline methods. A
FEATURES Large port for maximum efficiency Adjustable tubing sensitivity High slug lifting capacity Preset spring compression Available in various alloys and elastomers Port sizes 1/4" 1/2"
76 12/06/00
BJR
FEATURES Simple rugged design Spring loaded valve Field proven operation Integral reverse check 1/8 - 3/8 port sizes
77 12/06/00
BJR
production pressure operated gas lift valve used in continuous flow operations. The RV-15R is run on the
appropriate R series latch in a M series side pocket mandrel. These valves are particularly suited to deep, high flowing pressure gas lift wells, dual installations and in completions with fluctuating injection pressures. The RV15R uses internal orifices to control maximum gas passage.
FEATURES Spring loaded, bellows actuated Throttling type closure Liquid-charged Monel bellows Port sizes 1/8 - 1/4"
78 12/06/00
BJR
installations. The RW flow regulator and appropriate R series latch is run in the M series side pocket mandrel. Camco has adapted the Waterman flow regulator principle to subsurface equipment to allow control of the quantity of fluid entering a single- or a multiple-zone water injection system.
FEATURES Simple rugged design Field proven operation Available in various alloys Various packing material available
80 12/06/00
BJR
FEATURES Various port sizes (1/8 - 3/8) Simple rugged design Field proven operation Available in various alloys and elastomers APPLICATION AND OPERATION The RWW flow regulator will maintain a predetermined and preset flow rate regardless of changes in pressure
81 12/06/00
BJR
FEATURES Large 3/4" port size Use of stainless steel or nickel alloys Tension bar design Predetermined differential pressure for tension bar separation
82 12/06/00
BJR
FEATURES Wide range of orifice sizes (1/8 - 7/16) Tension bar design Predetermined differential predictable response to pressure separation
83 12/06/00 BJR
FEATURES Dual spring loaded reverse checks Available in numerous tension values Wide choice of orifice sizes (1/8 5/8) Various packing and seal materials available Available in stainless steel or high nickel alloys
84 12/06/00
BJR
FEATURES Large port for maximum efficiency Adjustable tubing sensitivity High slug lifting capacity Preset spring compression Available in various alloys and elastomers
85 12/06/00
BJR
FEATURES Large port for maximum efficiency Adjustable tubing sensitivity High slug lifting capacity Preset spring compression Available in various alloys and elastomers
86 12/06/00
BJR