Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
DESCRIPTION
FEATURES
*Low external components count. *Wide operating voltage : 3 - 13 V. *Internal regulated supply for constant current operation. *DC selection of AM/FM mode.
DIP-16
BLOCK DIAGRAM
AM IF OUT AM/FM IN HF GND IF bypass AGC bypass AM/FM OUT IF Detector IN +Vcc
16
15
14
13
Regulator
AM/FM IF AM HF MIXER
AM/FM discriminato
Audio amplifier AM LO
5
AM local OSC
6
AM HF IN
7
HF bypass
10
11
12
SYMBOL
VCC ICC PD RJ-A TOPX TSTG
VALUE
11 44 600 100 -18~65 -40~125
UNIT
V mA mW C/W C C
UTC
QW-R110-002,A
UTC KA22427
PARAMETER
Quiescent Circuit Current
ELECTRICAL CHARACTERISTICS
SYMBOL
ICCQ
MIN
7 10 2.0
TYP
12 17 2.4 57
MAX
17 23 3.1
UNIT
mA
Pin 16 Terminal Voltage Limiting Voltage Internal Regulated Voltage Pin 16 Voltage Signal to Noise Ratio Maximum Sensitivity Power Output Total Harmonic Distortion Voltage Gain
SW1FM,ICC=42mA SW1FM,VCC=5.5V,-3dB V16=2.4V,VR=Min. SW1AM,ICC=42mA SW1AM,VCC=9V SW1AM,VCC=12V,VIN=37dB SW245,V16=1.4V SW1AM,VCC=5.5V, SW28,VIN=37.5dB SW28,VCC=5.5V,f=1KHZ VR=Min. VR=Min. THD=10% SW245,ICC=42mA,f=1KHZ VOUT=2V SW28,VCC=5.5V,f=1KHZ VR=Min.
V dBV
13.2
14.0 1.9
V V V dB
3.0 20
W 0.5 40 4.0 % dB
SYMBOL
Rip2(AM) Cip2(AM) Rip2(FM) Cip2(FM) Rop4 Cop4 Rip6 Cip6 Rip14(AM) Cip14(AM) Rip14(FM) Cip14(FM) Rop15(AM) Cop15(AM) Rop15(FM) Cop15(FM)
TEST CONDITIONS
f=465KHZ f=465KHZ f=10.7MHZ f=10.7MHZ f=465KHZ f=465KHZ f=1MHZ f=1MHZ f=465KHZ f=465KHZ f=10.7MHZ f=10.7MHZ f=465KHZ f=465KHZ f=10.7MHZ f=10.7MHZ
MIN
TYP
200 3 30 3.5 300 6 50 5 300 3.5 300 4 300 5.5 300 6
MAX
UNIT
K pF K pF K pF K pF K pF K pF K pF K pF
UTC
QW-R110-002,A
UTC KA22427
TEST CIRCUIT
V13
Vcc Icc
470 F
0.047 F
220pF
OUTPUT
470 F SW2
1.2k
4 3 2
3 2
470 F 8 220 F 45
4.7k 0.001 F
GND
FM AM
SW1
10pF
16
15
14
13
12
11
10
UTC KA22427
Rg=50
22k
HF SIGNAL
~
1
8
0.022 F 3.3 F
3 2
3 2
0.01 F
680pF
5k
2 1 6 6 1
51pF
0.047 F 50
AUDIO SIGNAL
50
0.022 F 0.022 F
FM AM SW1
FM IF INOUT
AM HF INPUT
VOD
INPUT
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
UTC
QW-R110-002,A