Sei sulla pagina 1di 24

2013/4/5

Security Level: Internal Use Only

OptiX RTN 980 Product Introduction


MW Dept HCPT Project
www.huawei.com

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Preface
This document describes the new features of the OptiX RTN 900 V100R003 (RTN 900 V1R3 for short). After reading this document, you will be aware of the indicators and applications of new devices/boards and functions of the RTN 900 V1R3.

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 2

Contents

New Devices of the RTN 980 V1R3 New Boards of the RTN 900 V1R3

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 3

RTN 980 Product Positioning


Access layer Coarse convergence layer Dense convergence layer

E1/STM-1/ IMA E1/FE/GE RTN 910 RTN 950 RTN 980 RTN 910 RTN 910/950

BTS/NodeB/eNodeB

BSC/RNC/aGW

As nodal devices, RTN 980s are mainly used for dense convergence on mobile bearer networks.

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 4

Indicators of RTN 980s


Indicator Height of an IDU chassis Pluggable board Number of microwave directions Radio type 5U Supported 1 to 14 TDM radio (including PDH/STM-1/2xSTM-1) and IP microwave (including Hybrid radio and Packet radio) 1+0 non-protection, N+0 non-protection (N 14), 1+1 protection, N+1 protection (N 7), and XPIC configuration 128x128 VC-4 cross-connections, and VC-12/VC-3 crosscross-connect capacity connections equivalent to 32x32 VC-4 cross-connections Switching capacity Protection for system control, switching, and timing units
HUAWEI TECHNOLOGIES CO. LTD.

Performance

RF configuration mode

22 G bit/s

1+1 hot backup

Huawei Confidential

Page 5

Slot Allocation of an RTN 980


An RTN 980 has 19 slots numbered from left to right and up to down. As in the figure: Slots 1-14 are for hot-pluggable service boards. Slots 1 and 2, slots 3 and 5, slots 4 and 6, slots 7 and 9, slots 8 and 10, slots 11 and 13, and slots 12 and 14 are

slot pairs.
Slots 15 and 20 are for system control, switching, and timing boards. Slots 26 and 27 are for PIU boards that provide 1+1 hot backup for each other. Slot 28 is for a fan board.
SLOT 26 (PIU) SLOT 13 (EXT) SLOT 11 (EXT) SLOT 9 (EXT) SLOT 28 (FAN) SLOT 7 (EXT) SLOT 27 (PIU) SLOT 14 (EXT) SLOT 12 (EXT) SLOT 10 (EXT)

SLOT 20 (CSHN)
SLOT 8 (EXT)

SLOT 15 (CSHN)
SLOT 5 (EXT) SLOT 3 (EXT) SLOT 1 (EXT) SLOT 6 (EXT) SLOT 4 (EXT) SLOT 2 (EXT)

Relationship of a slot pair

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 6

Board Support of RTN 980s


Board Function and Indicator
System control, switching, and timing board TDM cross-connect capacity: 20 Gbit/s higher order cross-connections and 5 Gbit/s lower order cross-connections. Data switching capacity: 22 Gbit/s crossconnections GE (RJ45/SFPo): 2 STM-1/4 (SFPo): 2

Valid Slot

CSHN

Slots 15 and 20

PIU FAN AUX

-48 V power supply board 3.3 V centralized power interface to service boards Slots 26 and 27 Equipment power reporting Intelligent adjustment detection of fan speed Auxiliary management interface board, compatible with RTN 950s Slot 28 Slots 1 to 14

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 7

Board Support of RTN 980s (Cont.)


Board EM6T Interface 4xFE (RJ45) 2xGE (RJ45) 4xFE (RJ45) 2xGE (SFP, optical or electrical) 32x75-ohm/120-ohm Smart E1 interface, which is for CES E1, IMA E1, and Fractional E1 16x75-ohm/120-ohm Smart E1 interface, which is for CES E1, IMA E1, and Fractional E1 2xSTM-1 (SFP, optical) 16xE1(75/120) Service Capacity 1 Gbit/s Valid Slot Slots 1 to 14

EM6F

1 Gbit/s

Slots 1 to 14

MD1

1 Gbit/s

Slots 1 to 14

ML1 SL1D SP3S

1 Gbit/s

Slots 1 to 14 Slots 1 to 14 Slots 1 to 14

SP3D

32xE1(75/120)

Slots 1 to 14

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 8

Board Support of RTN 980s (Cont.)


Board Interface Hybrid IF board, a maximum air-interface capacity of 363 M/2xSTM-1 XPIC IF board, a maximum air-interface capacity of 363 M/2xSTM-1 TDM IF board, a maximum air-interface capacity of 53xE1/1xSTM-1 Hybrid IF board, a maximum air-interface capacity of 363 M XPIC IF board, a maximum air-interface capacity of 363 M Backplane Bandwidth Valid Slot

ISU2

1 Gbit/s

Slots 1 to 14

ISX2

1 Gbit/s

Slots 1 to 14

IF1

Slots 1 to 14

IFU2

1 Gbit/s

Slots 1 to 14

IFX2

1 Gbit/s

Slots 1 to 14

Page 9 HUAWEI TECHNOLOGIES CO. LTD. Huawei Confidential

Typical Application of RTN 980s - TDM


Application 1: TDM services from BSs are converged and then transmitted to an optical transmission network.

This application pertains to the backhaul of TDM services from BSs. The services from BSs are converged on an RTN 980 on a chain, tree, or ring network. If an NE needs to transmit 16xE1 services, 1+1 HSB protection must be configured for the NE. In addition, this NE provides STM1/STM-4 optical interfaces in the upstream direction, which is configured into a 1+1 MSP group. RTN 980s connect to a backbone network, and is configured into a ring MSP group with OptiX OSN equipment. Note: 2.5 Gbit/s optical interfaces are not supported in the R3C00 version.
HUAWEI TECHNOLOGIES CO. LTD. Huawei Confidential Page 10

Typical Application of RTN 980s - Hybrid


Application 2: Hybrid services from 2G/3G BSs are converged and then transmitted to an optical transmission network. Convergence of multiple types of IF boards

RTN RTN Hybrid MW TDM MW

RTN980 RTN Hybrid MW STM-N/GE Ring MSTP/PTN

On the access side, TDM and Ethernet services are transmitted to one site and are converged on Hybrid IF boards on the RTN 980. Then, the services are transmitted to optical transmission networks. Specifically, TDM services are transmitted on an SDH network; Ethernet services are transmitted on a GE network.

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 11

Typical Application of RTN 980s - Packet

The RTN 910 receives Packet services from the BS, and the RTN 950 or RTN 980 converges services. The services from the RTN 950 are transmitted to the PTN 3900 through a GE access ring. The RTN 980 converges services from eight microwave directions or more. The RTN 980 provides two GE ports in the upstream direction to connect to the PTN 3900. In this way, microwave equipment and other optical network equipment can be integrated as one. In addition, Nodal microwave equipment instead of stacked devices can be used to receive services from multiple microwave directions.

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Contents

New Devices of the RTN 980 V1R3 New Boards of the RTN 900 V1R3

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 13

Board Support of RTN 900 V1R3 (Newly Developed)


Board
CSHN

Function
System control and cross-connect board: Integrates service interfaces; 2xSTM-1/STM-4; 2xGE (RJ45/SFP) dual-mode New generation general XPIC IF board, supporting SDH/Hybrid/Packet XPIC microwave New generation general XPIC IF board, supporting SDH/Hybrid/Packet XPIC microwave 32xSmart E1 interface board (75 ohms/120 ohms) 16xSmart E1 interface board (75 ohms/120 ohms) Fan board Power supply board

Product
RTN 980

ISX2
ISU2

RTN 910/950/980
RTN 910/950/980 RTN 910/950/980 RTN 910/950/980 RTN 980 RTN 980

MD1
ML1 FAN PIU

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 14

Introduction to the CSHN Board


The CSHN board is the system control, switching, and timing board,

providing 2xSTM-1/2xSTM-4 ports and 2xGE ports.


Functions and Features
Supports Supports Supports

2xSTM-1/2xSTM-4 ports and 2xGE ports, and 14 service slots. a packet switching capability of 22 Gbit/s. the TDM switching function, that is, 128x128 VC-4 cross-connections and lower

order cross-connections equivalent to 32x32 VC-4 cross-connections.


Supports

one NMS serial port/network port, one NE cascading port for network

management communication, as well as NE management and query.


Provides

one external clock port (2048 kbit/s or 2048 kHz, wayside E1 port)

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 15

Application Scenario of the CSHN Board


Configuration Principles
CSHN boards are a must for an OptiX RTN 980. If an OptiX RTN 980 needs one CSHN board, install the board in slot 15; if an OptiX RTN 980 needs two CSHN boards, install the boards in slots 15 and 20. The two STM-1/STM-4 SFP ports on a board need be manually set to the STM-1 or STM-4 mode. The two GE ports on a board need be manually set to SFP or RJ45 mode.

Valid Slots
Board

NE Type RTN 980

Valid Slot Slots 15 and 20

CSHN

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 16

Typical Application of STM-1/STM-4 Compatible Optical Interfaces


1. RTN 980s can be networked with fiber-optic equipment. That is, RTN 980s can be networked with MSTP equipment to form an STM-4 ring, or can be networked with MSTP equipment to form an STM-1 ring. 2. If there are two system control, switching, and timing boards, the boards cannot be configured into STM-1 linear MSP with extended boards.

RTN

RTN

RTN

RTN

RTN980 RTN STM-4 MSTP RTN STM-1

RTN980

MSTP

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 17

Introduction to the ISU2 Board


The ISU2 board is a universal IF board used on the RTN 910/950/980. It provides one IF port for integrated IP microwave. Functions
Provides

one IF port.

Supports

TDM/Hybrid/Packet radio in Native E1+Ethernet, Native

STM-1+Ethernet, or SDH (1xSTM-1 or 2xSTM-1) mode.


Supports

the AM function.

Service Bus on Backplane Provides 2xVC-4 Telecom bus and 1xGE bus to connect to the system control, switching, and timing board.

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 18

Application Scenario of the ISU2 Board


Configuration Principles If the equipment is configured with FD or SD protection, the boards must be installed in paired slots. The XPIC function of ISX2 board needs to be set to Disable when the ISU2 board is interconnected with the ISX2 board.

Valid Slots
Board

NE Type RTN 910 RTN 950 RTN 980

Valid Slots Slots 3 and 4 Slots 1 to 6 Slots 1 to 14


Huawei Confidential Page 19

ISU2 ISU2 ISU2

HUAWEI TECHNOLOGIES CO. LTD.

Introduction to the ISX2 Board


The ISX2 board is a universal XPIC board used on the RTN 910/950/980. It provides one IF port for integrated IP microwave and

XPIC function.
Functions
Provides Supports

one IF port. TDM/Hybrid/Packet radio in Native E1+Ethernet, Native

STM-1+Ethernet, or SDH (1xSTM-1 or 2xSTM-1) mode.


Supports Supports

the XPIC function. the AM function.

Service Bus on Backplane Provides 2xVC-4 Telecom bus and 1xGE bus to connect to the system control, switching, and timing board.
HUAWEI TECHNOLOGIES CO. LTD. Huawei Confidential Page 20

Application Scenario of the ISX2 Board


Configuration Principles
If the equipment is configured with FD or SD protection, the boards must be installed in paired slots. The XPIC function of the ISX2 board is set to Disable when the ISU2 board is interconnected with the ISX2 board. An XPIC workgroup consists of two ISX2 boards that send signals to each other through XPIC buses.

Valid Slots
Board

NE Type RTN 910 RTN 950 RTN 980

Valid Slot Slots 3 and 4 Slots 1 to 6 Slots 1 to 14

ISX2 ISX2 ISX2

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 21

Introduction to the ML1/MD1 Board


The MD1 board transmits and receives a maximum of 32xE1 signals, and the ML1 board transmits and receives a maximum of 16xE1 signals. The board supports 75-ohm E1 coaxial cables and 120-ohm E1 twisted pair cables to perform conversion between PDH services and packets (cells). The service types at each port are agile to process CES and IMA signals. The board supports hot swap. Functions IMA: The MD1 board supports 32 IMA groups. Each IMA group has a maximum of 16 members. The ML1 board supports 16 IMA groups. Each IMA group has a maximum of 16 members. Supports the Fractional mode. ATM: The MD1 board supports 512 ATM remote connections. The ML1 board supports 256 ATM remote connections. Supports ATM PWE3. Supports Fractional ATM. CES: The ML1 board supports 16xE1 signals, and the MD1 board supports 2x16 E1 signals. Supports CESoPSN and SAToP. Supports Fractional CES. Service Bus on Backplane

The service bus on backplane communicates signals between the two Ethernet GE ports and the
main and standby boards on the RTN 910, RTN 950, and RTN 980.

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 22

Application Scenario of the ML1/MD1 Board


Configuration Principles
The SL91MD1A/B and SL92ML1A/B boards can be used on the RTN
910/950/980, and can be installed in all the slots for interface boards.

Valid Slots
Board NE Type RTN 910 SL91MD1A/B RTN 950 RTN 980 RTN 910 SL92ML1A/B RTN 950 RTN 980 Slots 3 and 4 Slots 1 to 6 Slots 1 to 14 Slots 3 and 4 Slots 1 to 6 Slots 1 to 14 Valid Slots

HUAWEI TECHNOLOGIES CO. LTD.

Huawei Confidential

Page 23

Thank You
www.huawei.com

Potrebbero piacerti anche