Documenti di Didattica
Documenti di Professioni
Documenti di Cultura
ASME B16.5-2003
14
15
16
17
18
19
20
21
22
23
24
Class
150
Class
300
400
600
Class
900
Class
1500
Class
2500
Class
150
Class
300
Class
400
Class
600
Class
900
Class
1500
Class
2500
...
13.00
...
...
...
...
...
14.00
...
...
...
...
14.25
...
...
...
...
...
14.62
...
13.38
...
...
...
16.75
...
0.16
...
...
...
...
...
0.22
...
...
...
...
0.22
...
...
...
...
0.19
...
...
...
...
0.16
...
...
...
...
...
0.16
...
0.19
...
...
...
0.25
16.00
...
...
16.75
...
...
16.25
...
...
...
...
16.50
...
...
...
...
...
17.25
...
...
...
...
...
...
19.50
0.16
...
...
0.12
...
...
0.22
...
...
...
...
0.22
...
...
...
...
0.19
...
...
...
...
0.16
...
...
...
...
...
0.19
...
...
...
...
...
...
0.31
...
...
...
19.00
...
18.00
...
...
...
20.00
...
18.38
...
...
...
...
...
19.25
...
...
...
...
...
...
...
...
...
...
0.12
...
0.22
...
...
...
0.22
0.22
...
...
...
0.22
0.19
...
...
...
0.19
...
0.16
...
...
...
...
...
0.22
...
...
...
...
...
...
...
...
...
21.50
...
...
...
...
...
22.62
...
20.62
...
...
...
23.38
...
21.50
...
...
...
...
...
...
...
...
...
...
0.12
...
...
...
...
...
0.22
...
...
...
...
0.22
...
...
...
...
0.19
...
0.16
...
...
...
0.19
...
0.31
...
...
...
...
...
...
...
...
...
23.50
...
...
...
...
...
25.00
...
...
...
...
...
25.50
...
24.12
...
...
...
26.50
...
...
...
...
...
...
0.12
...
...
...
...
...
0.22
...
...
...
...
0.22
...
...
...
...
0.19
...
...
...
...
...
0.19
...
0.31
...
...
...
0.38
...
...
...
...
...
28.00
...
...
...
...
29.50
...
...
...
...
30.38
...
...
...
...
31.25
...
...
...
...
0.12
...
...
...
...
0.25
...
...
...
0.25
...
...
...
0.22
...
...
...
...
0.22
...
...
...
...
0.44
...
...
...
...
GENERAL NOTES:
(a) Dimensions are in inches.
(b) For facing requirements for flanges and flanged fittings, see para. 6.4.1 and Fig. F7.
(c) For facing requirements for lapped joints, see para. 6.4.3 and Fig. F7.
(d) See para 4.2.7 for marking requirements.
NOTES:
(1) Height of raised portion is equal to the depth of groove dimension E, but is not subjected to the tolerances for E. Former full-face contour may be used.
(2) Use Class 600 in sizes NPS 12 to NPS 312 for Class 400.
(3) Use Class 1500 in sizes NPS 12 to NPS 212 for Class 900.
(4) For ring joints with lapped flanges in Classes 300 and 600, ring and groove number R30 are used instead of R31.
TOLERANCES:
E
(depth) +0.016, 0.0
F
(width) 0.008
P
(pitch diameter) 0.005
R
(radius at bottom)
R 0.06 +0.03, 0.0
R > 0.06 0.03
23 deg (angle) 12 deg
161